Search Documents

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By Heber E. Peterson, Sill. Claude W.

"INTRODUCTION In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate. It seemed likely that the same general procedure could be used in determining semimicro quantities pf uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant in turn permits the use of the very stable indicator, ferroin; with its sharp color change and exactly reproducible blanks.Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Glen (5). The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months."

Jun 1, 1952

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By Eleanor Abshire

This bibliography is the second in a series that covers the current technical literature relating to the metallurgy of zirconium. The rapid advance in zirconium technology makes it mandatory that abstracts be prepared and compiled as soon as possible to have maximum value; therefore, the information in this volume is not arranged chronologically. As a service to research and production groups, succeeding bibliographies will be issued as new acquisitions accumulate in the Zirconium Information Center sponsored by the Department of the Navy, Bureau of Ships and the Bureau of Mines at the Bureau's Northwest Electrodevelopment Laboratory, Albany, Oreg. The initial volume, Information Circular 7771, Bibliography of Zirconium, covering 969 abstracted reports and 645 United States and foreign patents, was published in April 1957.

Jan 1, 1958

In 1970, the U. S. Bureau of Mines contracted with Theodore Barry and Associates, a management consulting firm, to perform a one-year industrial engineering study of working-face hazards in underground bituminous coal mines. The field data was accumulated from industrial engineering observations in fifty underground mines. Supporting data for the analysis was derived primarily from the Bureau's fatal accident reports for the years 1966 through 1970. This report, Industrial Engineering Study of Hazards Associated with Underground Coal Mine Production, consists of three main parts: 1) The Fatal Accident Reports Analysis, 2) The Industrial Engineering Analysis, and 3) Multiflow Process Charts and Standard Time Data. The Fatal Accident Reports Analysis (Volume I, Section II) is based upon individual USBM fatal accident reports for 1966-1970. These were read, coded and computerized in terms of 84 significant variables. Cross-tabulations of these variables have been used to identify major underground hazards and to quantify significant causal factors. A very strong relationship was found to exist between fatal accident occurrences and low task experience. This led to a recommendation for formalized training, certification and supervision programs for miners. Victim compliance with federal regulations, mine regulations and supervisor instructions was analyzed, indicating that supervisors provide the most crucial communication link to workers. Thus, every attempt should be made to ensure the competence of immediate supervisors in the industry. Analysis of roof fall variables revealed a fatal propensity on the part of the miners to work under unsupported roof or under support conditions that are marginal. The technical approach to the problem is to make it physically impossible for a miner to work under these conditions; the behavioral approach is to ensure adequate training and develop proper safety attitudes among the miners. The Fatal Accident Reports Analysis revealed a need for normalizing data to interpret the results more accurately.

Jan 1, 1971

By BUREAU OF MINES

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its prin- cipal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctua- tions, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic informa- tion and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that produc- tion rates and reserves have a proportionate relationship.

Jul 1, 1964

The complex organic chemicals in coal differ from those in petroleum mainly by the ratio of carbon atoms to hydrogen atoms; this ratio is about 2 for coal and 1 for petroleum. By changing the ratio, coal can be converted into compounds similar to those found in petroleum. In. very simplified form, omitting here the special conditions required, the paths by which this can be done are: [ ] Part or all of the coal is first gasified by reaction with steam and oxygen, either in a gasifier or while the coal is still in place underground. The resulting gas is mainly hydrogen and carbon monoxide, with impurities that .must be removed before further processing by one of the following routes.

Jan 1, 1959

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled predominantly by rising personal consumption expenditures as well as growing government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the minerals-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The low level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1987

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980

By Joseph L. Jordan

Coal is essential to America?s future energy needs. To meet these needs mining methods must be safe, economical, and environmentally acceptable. Belt conveyor systems for coal haulage from surface mines offer great potential in this situation. The advantages over conventional truck haulage are particularly promising for area strip mines in western coal fields such as the Powder River Basin where relatively thick, flat-lying coal seams occur. The current demand for low-sulfur coal specifically emphasizes the need for better mining methods in these areas. Underspoil haulage is the term applied to transportation of coal from the pit to the surfate in area strip coal mines by belt conveyors in tunnels under the spoil. The advantages over trucks include lower manpower requirements, greater pit safety and efficiency, and improved reclamation procedure. This evaluation includes a comparison of total mining costs for truck haulage versus six variations of the underspoil haulage concept. The more efficient of these underspoil haulage systems have economic advantages over truck haulage which become more pronounced with deeper overburden, thicker coal, and higher annual production.

Jan 1, 1977

By N. B. Aughenbaugh

This report summarizes the results of an investigation into the causes of coal mine roof instability caused by the environmental characteristics of the air ventilated through a mine. The field studies, which were mostly in the Illinois Coal Basin, concentrated on collecting data of surface weather conditions, mine air characteristics (relative humidity and temperature), roof material types, roof movements, and characteristics of roof deterioration. The field studies revealed seasonal changes in weather are reflected in the mine air. The intake air undergoes rapid tempering along its course as it interacts with the ambient mine conditions. There are seasonal moisture interchanges between the mine rock and air, and a mine will lose more water than it gains on a yearly basis. The field studies also established that when the roof rock is shaley, seasonal changes in the humidity will cause roof deterioration because of the detrimental action of moisture on the shale. Roof falls were inventoried and classified by geometry. In the laboratory investigations, physical tests proved unreliable for evaluating shales for roof stability. The Franklin slake test lacks the sensitivity needed to differentiate shale durability for roof stability. A relative humidity test that reveals the sensitivity of a shaley rock to moisture change was devised. Environemntal chamber studies showed that neither temperature nor barometric pressure have a direct influence on shale durability. Photoelastic studies showed that the rate and depth of moisture absorption into a shale is controlled by bedding planes, fractures, and holes interrupting the exposed surface.

Jan 1, 1976

The U.S. economy showed further strength during the third quarter of 1983, continuing the upward trend discussed in the last two issues of Minerals and Materials. The National Association of Purchasing Management composite index increased to a 10-year high of 67. 1 in July. (A value of 50 or greater indicates expanding industrial activity.) The index, a weighted composite of new orders, production, employment, vendor performance, and inventories, is derived from a survey of purchasing agents for about 250 industrial firms. Investment and Other National Economic Indicators The strong consumer surge of second quarter 1983 was reinforced during the third quarter by the performance of private investment. Because of this, many analysts became more optimistic about the strength of the recovery and its potential for being sustained. Capital investment growth, negative since 1980, was positive for every investment component in the third quarter of 1983. Preliminary estimates indicate a real increase of $1.4 billion (at an annual rate) in private investment expenditures on nonresidential structures, an increase of $4.3 billion (at an annual rate) for producers' durable equipment, and an increase of $4.8 billion (at an annual rate) in real inventory levels. The second quarter 1983 increase in expenditures on producers' durable equipment was the first indicator that investment recovery would occur during the rest of the year (table 1). Corporate profits in total manufacturing increased $6.5 billion from first quarter to second quarter 1983 (table 2).

Jan 1, 1983

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973

By Paul T. Allsman, William H. King

This paper describes the mineral deposits and discusses mining and milling methods and related operating conditions in an important gold , silver , lead , and zinc producing area in Ouray , San Juan , and San Miguel Counties , Colo . , embracing 250 square miles . The area is extremely rigged , ranging in altitude from 8,000 to 14,000 feet . White men first penetrated the area in 1860 , when a group known as "Baker's party " reached the Animas River at the present site of Silverton . Difficulty with the Ute Indians and severe winter conditions forced the group to leave and discouraged prospecting until 1870 when a second party reached the area and succeeded in producing 27 tons of ore yielding $ 150 a ton in gold . In 1874 , a treaty with the Indians opened the way for settlement , and mining was established . The total production of recovered gold , silver , copper , lead , and zinc from 1873 to 1947 in the three counties is valued at $347,057,047 . The greatest amount of the total production of metals has come from quartz veins in a series of volcanic flows and tuffs covering the area and comprising a blanket 4,000 to 6,000 feet thick . The igneous rocks were laid down upon an old , erosion surface and are underlain by Paleozoic and Mesozoic sedimentary rocks and pre - Cambrian metamorphic rocks . The entire series has been intruded in late Tertiary time by volcanic dikes and larger intrusive masses . Because of the great differences in relief generally , mining is con-" ducted through long adits to a depth of nearly 3,000 feet below surface in places . Walls of the veins generally stand well , and shrinkage stoping is the most common method of mining . As virtually all of the ore is sulfide below the zone of oxidation , flotation is the common method of milling . Generally , where gold is important , provision is made for its removal by jigs . Bulk concentration of the sulfides is practiced at smaller mills , but the larger operations make a selective lead and zinc concentrate or a lead , zinc , and copper . concentrate . ·

Mar 1, 1950

By S. L. Windes

This report presents a tabulation of the physical and petrographic properties of Over 100 rock types from operating mines or mineral-investigation projects. The physical properties include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength, (modulus of, rupture) Impact toughness Abrasive hardness Scleroscope hardness Modulus of elasticity (Young's modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1949

Since mid-July, most domestic producers have been marketing 99.5 percent unalloyed aluminum ingot at 53-57 cents per pound. Dealers in the United States have recently quoted ingot at 52.3-52.8 cents. On October 2, London Metal Exchange will trade aluminum, selling contracts on a cash and a 3-month basis. New York dealers were quoting August ingot at 52.3 52.8 cents. The Bonneville Power Administration announced that, effective December 20. 1978, electric power rates charged primary aluminum producers in the Pacific Northwest would be increased The increase (equivalent to about 4 cents per pound of aluminum produced) will raise the average rate to about 8.7 mills per kw-hr compared to 3.2 mills per kw-hr.

Jan 1, 1978

By Bernard Lewis

This report summarizes the fundamental research and technical studies conducted by the Explosives Branch of the Bureau of Mines from July 1, 1943, to June 30, 1949. It is the thirteenth of a series of annual reports, which have aimed to bring to the reader a resume of the research results that have appeared in published form during each fiscal year. The work of the Explosives Branch covers a number of activities - explosives research, explosives testing, flame and combustion research, flammability of gases and vapors, dust-explosions research, and technical studies in the experimental mine. An important part of the work of the branch is fundamental research to advance our knowledge and understanding of explosion processes. Considerable emphasis has been placed on studies of ignition and flame stabilization, as it is felt that an understanding of these processes should assist materially in alleviating explosion hazards in coal mines. The results are also finding important application in the development of jet propulsion. Studies of the explosibility of gases, vapors, and dusts saving thousands of lives and are preventing the destruction of much property. In innumerable instances in which potential explosion hazards exist, safe operating procedures have been recommended from data taken in the Laboratory. Aware of the value to national security of research results of combustion, flame, and explosion, the Army, Navy, and Air Forces are actively supporting important phases of this fundamental research.

Jan 1, 1950

By Oliver Bowles

In 1940 the Bureau of Mines issued a report describing all the cement plants of Latin America, their design, capacity, and output, and the cement imports, exports, and requirements of the several countries. Since that time there has been such great activity in cement plant construction that a revision of the paper is highly desirable. The present compilation comprises the essential data in the previous report together with descriptions of all cement plants completed, under construction, or planned since that date and an overall picture of the supply and requirement situation of each country. Before World War I, Latin America was one of the world's largest export markets for cement. Its dependence on outside sources created no special problems of supply until the shortage of shipping and abnormally high prices of the First World War stimulated a movement toward greater self-sufficiency. Under this incentive many cement plants were constructed, and several countries were able by 1939 to manufacture enough cement for their modest needs. Substantial imports were still required for many important areas, and as the volume of demand was rapidly increasing the Latin American countries as a whole were far from self-sufficient in cement when tine Second. World War began. South and Central America depended to a large extent on European countries, chiefly Germany arid Belgium and to a smaller degree Scandinavia, United Kingdom, France, and Italy, to Supply their cement shortages. The cost of manufacture in these European countries was much lower than in the United States, and transportation expense had been kept at a particularly low level because of the two-way trade that had been developed. Ships destined for Latin American ports for coffee, tropical woods; fruits, and other native products could carry cargoes of cement on their westward voyages at very low cost In some instanced cement was taken in exchange for South American -products because cash was not available. Great Britain had withdrawn from this market to quite an extent because of low prices and because trade with its own Empire had been increasingly fostered. United States trade in cement with Latin America had been confined principally to white and other special varieties. In few places could ordinary portland cement made in the United States compete in price with the European products; although in general it was of better quality and cool d be delivered more promptly.

Jan 1, 1946

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

Kaiser Aluminum & Chemical Corp. announced that it planned to spend $66 million to increase the efficiency of its Baton Rouge, Louisiana, alumina plant. The improvements are designed to reduce energy consumption but will not change the annual capacity of the plant, now rated at about one million short tons. The project was expected to be initiated immediately and be completed by 1982. ALUMINUM Producers in this country posted unalloyed 99.5 percent aluminum ingot at 53-57.5 cents per pound, yet actual selling prices were closer to 53 cents. Domestic merchants quoted unalloyed ingot on a spot basis at 54-56.3 cents. London Metal Exchange 3-month forward contracts fell during November's trading from 55,2 cents to 52.8 cents per pound.

Jan 1, 1978