Search Documents

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By C. T. Sheeran

The Bureau of Mines investigated a microprocessor-based real-time control and monitoring system for uranium mining applications. The system is capable of controlling and monitoring up to 768 stations within 3 km of the central processor on a common four-wire cable. It can be used in conjunction with detectors to continuously monitor and display radiation working levels at points throughout the mine. Surface alarms are sounded for critical situations such as rapid radiation buildup, loss of power to monitors or fans, and changes in air door position. Permanent records of all changes are automatically printed out with their time of occurrence. Printouts can also be obtained for shift reports or trend logs. The system can be used to remotely control fan startup and shut-down, and also can alert miners of underground conditions by blowing horns or turning on lights. Battery backup keeps the system operative for up to 4 h in case of a mine power outage. A special software feature permits automatic, time-delayed, sequential restart of fans.

Jan 1, 1984

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all mineral to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of force applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective. A consideration of the possibilities of such a method for crushing led to some experimental work of a preliminary nature, the results of which are embodied in this paper. No systematic program was followed in the work and the results are, therefore, not final and far from complete. The success attained so far, with the mediocre apparatus available seems to warrant a preliminary report, with the expressed hope that the work may be carried on as well-outline program covering such phases as have been impossible to investigate at this time.

Jan 1, 1931

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By Katherine A. Margolis

Refuge Chamber Expectations Training was created by a multidisciplinary team at the National Institute for Occupational Safety and Health (NIOSH) to inform miners of what to expect psychologically and physically if it became necessary to use a refuge chamber in a mine emergency. The presentation can be used either for one large group or for individual miners. The training is a multimedia Adobe Flash presentation containing pictures, audio, video, and interviews with miners who have used a refuge chamber in an emergency. It must be run on a computer with Adobe Flash Player installed (refer to the computer system requirements section).

Oct 1, 2009

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By R. L. Grant

The conventional gallery test used by the Bureau of Mines Explosives Testing Station and corresponding establishments in other countries to establish the permissibility of explosives serves principally to differentiate the relatively safe explosive from the positively unsafe one. It has been recognized for many years that a more definitive test is needed to measure the relative incendivity to firedamp of explosives and explosive devices. A new method - the oxygen-value test - for measuring this incendivlty quantitatively has been devised and is being tested at Bruceton, Pa. To date, this testing bas been limited mainly to straight nitroglycerin dynamites. It is planned to study application of the method to permissible explosives in the near future. These results will be reported later. In the present report, permissible explosives will not be considered specifically.

Jan 1, 1954

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By Richard J. Mainiero

The U.S. Bureau of Mines in cooperation with Jim Walter Resources, Inc. (JWR), Brookwood, AL, evaluated the use of sheathed explosive charges in breaking up large stones that can jam the feeder¬breaker or pan conveyor on longwalls and halt operations. Use of the sheathed charge reduced the downtime of the longwall panel to 15 to 30 min as compared with the 1 to 2 h required to drill and shoot the stone. Firing the sheathed charge at the face caused no significant damage to Iongwall equipment. Use of the sheathed charge also represented an improvement in safety by eliminating the exposure of miners to the inherent hazards of the face for extended periods of time. Another benefit, which is difficult to quantify, is the elimination of the temptation to shoot mudcaps or adobes, which is illegal in U.S. underground coal mines.

Jan 1, 1990

By John R. Bartels

Jan 1, 2009

By R. R. Nothdurft

The internal friction of eight single crystals of magnesium with orienta-tion ranging from 10° to 84° was measured at 33.5 kc and 272° C, and the results were interpreted in terms of the pinned-dislocation model proposed by Granato and Lucke. Results show that the strain-amplitude-dependent decrement varies with orientation in a manner predictable by the G-L model. Different values of strain-amplitude-independent decrement were observed at different orientation angles, but correlation with the theory was not conclusive. Problems and steps for further study are discussed.

Jan 1, 1965

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By G. A. Apell

Completion of 18 churn-drill holes totaling 2,218 feet and 3 diamond-drill holes aggregating 421.5 feet of drilling in the M.C. mine area, near Truman, Wis., provided information indicating the existence and trend of a zone of zinc mineralization extending for 1,000 feet west of the old M. C. shaft.

Jan 1, 1949

By F. E. Walker, S. J. Aresco, J. B. Janus

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal , expressed in British thermal units , and the composition as shown by proximate analyses . To these , when required , are added the ash- softening temperature , the free - swelling index , and the Hardgrove grindability index . Under most of these specification contracts the bidders guarantee the quality of the coal , and that guaranteed by the successful bidder becomes the standard of his contract . The deliveries are sampled in accordance with instructions 4/ issued by the Bureau of Mines ; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and , if it is not , a price adjustment is made . Analyses of the delivered coal and tipple samples ( samples collected at mine tipples as coal is being loaded into railroad cars or trucks ) provide valuable data for use in evaluating future bids . In addition , the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal . The Government purchased approximately 5 million tons of coal in fiscal year 1962. In connection with these purchases , the Bureau analyzed 7,114 samples . These are published ( table 1 ) for the use of Government officials and the public . A series of publications has been completed on coal analyses by States or , where production is small in any one State , by groups of adjacent States . In addition to analytical data showing composition and quality of coals of the States , the publications contain brief descriptions

Jan 1, 1963

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite. During the early years of these plants little success was anticipated from the use of bituminous coals and lignites, but in 1904 and 1905 it was fully demonstrated at the Government testing station at St. Louis that these fuels could be utilized to excellent advantage. However, although many producer-gas plants in daily operation are using bituminous coal and lignite, many power-plant men are still skeptical regarding the successful commercial use of these fuels.

Jan 1, 1916

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966