Search Documents

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By A. D. Garman

The mining ordinance of Costa Rica dates from 1830. In spite of the numerous attempts to enact a new ordinance , it has been so much amended and reamended during the hundred years of its existence either expressly or , more often , by implication , and sometimes by Executive Decrees of which the validity has been called in question - that in most cases no one but a lawyer thoroughly conversant with Costa Rican mining practice could properly advise with reference to it . The present attempt at a digest of these laws is based on the 1929 edition of Bolandi and Johanning - the only source available in Washington . Apparently this edition has no official character , and the editors themselves often made surmises although one would think that definite facts would be available in Costa Rica where it was published .

Jul 1, 1930

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By Cleo Griffith Rall

The method for determining the effective porosity, of oil- and gas- bearing sand described in this report is a development of an earlier method devised by Bureau of Mines. The apparatus has been improved and made more convenient to use, but the procedure has been in use for many years without essential changes. A tabulation at the end of the report gives the results of more than 2,000 porosity determinations for oil sands in the fields of 13 states. A selected bibliography of articles containing descriptions and evaluations of various methods of determining porosity Is a. part of this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and ,on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1949

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

A general analytical solution of the effect of an inclined contact separating two media of differing electrical properties on a normally incident plane electromagnetic field has been given (Geyer, 1972). These solutions for the electromagnetic response at any observation point P(r, [u]) are given in the form of inverse Lebedev-Kontorovich transforms. Two modes of excitation are considered: (1) case where current density flows across strike of the contact separating the media of differing electrical properties (only Er , E [u] , and Hx differ from zero) and (2) case where current density flows along-strike (only Hr , H [u] , and Ex differ from zero). The electromagnetic fields in the frequency range of interest and for the rock conductivities under consideration are quasi-static in nature so that to a first-order approximation the horizontal magnetic field at the surface of the earth is constant and continuous across the discrete discontinuity in resistivity for case (1) above, and so that the tangential derivative of the horizontal electric field at the surface of the earth is constant and continuous across the discrete discontinuity for case (2) above. Of course, it is well known that where large horizontal gradients in conductivity exist, there also exists large anomalous components of the vertical magnetic field (Weaver, 1963). The recognition of such anomalous components and their magnitudes due to the presence of lateral resistivity changes in the overburden becomes very important in any wavetilt type measurement which may be used to locate a miner. When the lateral change in resistivity becomes quite large, the integral solutions (expressed as Lebedev-Kontorovich transforms) simplify considerably and allow ready numerical evaluation. Examples of the amplitude and phase responses of the radial electric, horizontal electric, and vertical magnetic field in the vicinity of the contrast in resistivity are shown in Figures 2, 3, and 4. Of particular significance is the fact that the anomalous vertical magnetic field is three orders of magnitude larger near the contact than far from the contact. This fact implies that where large resistivity contrasts do occur in the rocks overlying mine workings, that significant errors may be present in wavetilt measurements as used above for location criteria! Another observation insofar as the anomalous vertical magnetic field is concerned is the linear variation of phase as one proceeds away from strike in induction number (increased distance or frequency). For a pulse-excited communications system this phenomena would have a bearing on where the zero crossings would occur (i.e., 'pulse breadth') in the transient coupling between any given source-receiver configuration and at any given receiver site.

Jan 1, 1973

By Irving Hartmann

1. Under the conditions of the tests described herein, the proper use of an incombustible stemming plug of the type discussed prevented ignitions of gas in all tests during the firing of 21 single shots of permissible explosive in cool. In two tests with multiple blasting (four and five shots each) no ignitions resulted. 2. The results of a few tests in this investigation and of numerous tests made previously indicate that fire-clay stemming of the same weight as an incombustible plug provides about the same degree of protection as the plug against gas ignitions during blasting of coal by permissible explosives. 3. The hazard of gas ignition on firing charges of non-permissible 40-percent gelatin dynamite in coal was reduced but not eliminated when the shot holes were stemmed with one or two incombustible plugs or with an equivalent weight of fire clay. 4. On the basis of this investigation, the Bureau of Mines considers the proper use of incombustible stemming plugs of the design tested, under the conditions of the tests described in this paper, to be of equivalent safety as the same weight of fire-clay stemming. This report does not constitute approval or disapproval of the incombustible stemming plugs by the Bureau of Mines. 5. The test data indicate that misfired charges in shot holes stemmed with the incombustible stemming plug cannot be disposed of with certainty by the procedure recommended by the manufacturer. In this investigation the misfired charges failed to detonate in 30 percent of the trials.

Jan 1, 1950

By P. B. Lorenz

Wettability measurements and laboratory waterflood tests were compared under a wide variety of conditions. Experiments were conducted with synthetic and natural crude oils, treated and untreated outcrop and oilfield sandstone cores, and synthetic brines with and without caustic, detergent, or phosphate additives. Measurements were made on equilibrated and unequilibrated systems at 77° and 150° F. Wettability was evaluated by the Bureau of Mines method from capillary pressure curves determined with a centrifuge. The waterflood data were fitted by empirical curves; the parameters of the curves characterize primary and subordinate production and also give the ultimate oil recovery. Results showed that wettability measurements at 77° F were useful predictors of recovery efficiency in waterflood tests run at both temperatures. Oil recovery in the early stages of waterflooding increased with increasing water wettability; however, the ultimate recovery was highest at a slightly oil-wet condition. The oil displaced at highest speed in the centrifuge was correlated with ultimate recovery in waterflood tests. Chemical additives to the brine sometimes lowered wettability and also sometimes improved waterflood recovery, but wettability and recovery were not correlated with additives present. The effect of additives on recovery in waterflooding was best seen in water-oil ratio curves.

Jan 1, 1974

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers' methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By D. Harrington

Misuse of explosives and heedless disregard of well-known safety rules covering the use of commercial explosives cause many avoidable accidents resulting in the death or maiming of men who can ill be spared by already undermanned industry at present, and who cannot be spared by their families at any tire. Blasting accidents, when not fatal, are usually serious; the past and present needless loss of life and maiming of men from this cause are appalling and types of waste that can and should be virtually eliminated. Dead, crippled, and maimed men are distinct losses to society as well as to industry, and compensation payments for such accidents represent only a portion of the financial loss, because the value of their lost potential production can only be surmised. By their very nature, explosives are dangerous to handle, otherwise they would not perform the services for which they are used; all men on a blasting crew are subjected to the results of the carelessness of any one member, and in many instances the misuse of explosives by one person has killed scores of fellow workers. Inexperienced men should be assigned to blasting operations only under the close supervision of men well-experienced in the work and familiar with its inherent hazards. Men should be selected for blasting crews that are known to be careful, willing to follow instructions, cool-headed, and unlikely to become excited in an emergency; they should be instructed in the safe handling of explosives in accordance with the safety rules established by the explosives -manufacturing companies or the safety codes of the various industrial organizations. Unfortunately, American industry has never adopted a uniform code for the safe handling of explosives; however, many mining companies have made rules that will eliminate most unsafe practices if established safe procedure is followed carefully. The Bureau of Mines has issued numerous pamphlets giving information on the causes of accidents due to explosives in the mining industry and indicating the ways in which a good proportion of those accidents can be avoided.

Jan 1, 1943

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By E. A. Magill

The Bureau of Mines has begun a study of the copper resources of the Cascade Mountains of Washington. The program includes reconnaissance of mineralized areas and examination and occasionally limited exploration of deposits that are considered characteristic of an area. The Bureau of Mines believes that published information may assist industry in searching for new sources of copper. The Miners Queen is one of a few Cascade Mountain deposits selected for prelim¬inary exploration. The investigation was not planned to delineate the ore body. A diamond-drilling program was carried out at the Miners Queen mine in the summer of 1955. Five diamond-drill holes were completed, totaling 628 feet. Two 35-foot shafts were dewatered, and all accessible underground and surface workings were examined.

Jan 1, 1957