Search Documents

By Jerry E. Olson

In 1985 the U.S. Bureau of Mines conducted a mineral survey of 68,458 acres of the Clan Alpine Mountains Wilderness Study Area (NV-030-102) which covers 196,128 acres in Churchill County, NV. Most of the area studied is underlain by Tertiary volcanic rocks. In the northeast corner of the study area, an upthrown block of Triassic sedimentary rocks partially extends into the area. The study area is probably part of a large eroded caldera. No major mines or active claims are within the study area. Field investigations included examination of workings in Starr Canyon, historical and recent mining activity near the mouth of Florence Canyon, other mining claims, and anomalous zones delineated by data from Great Basin GEM Joint Venture studies. No mineral resources were identified, but sample results indicate one significant mineralized zone situated along a northwest trend between the head of Starr Canyon and the head of Cherry Creek may contain precious metal resources. Further investigation of this zone is warranted.

Jan 1, 1987

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By D. Harrington

The Bureau of Mines was created in 1910 largely to determine methods of preventing coal-mine explosions; the Bureau's studies have proved that coal dust, except possibly that of some grates of anthracite, can initiate an explosion in the absence of gas and that its ability to extend or propagate an explosion of either gas or dust has been responsible for nearly all of the widespread explosions that have taken place in bituminous and other nonanthracite mines in the United States in the present century. It is believed by many persons that all atmospheric dusts may be harmful if breathed in large enough quantities for long enough time; bituminous coal dust is generally considered to be essentially harmless physiologically, yet there is abundant evidence of definite damage from inhalation of bituminous dust mixed or unmixed with the dust of other materials. Attention un¬questionably should be given to allaying dust in bituminous mines, especially at principal dust-producing sources. This publication enumerates some of the sources of dust and describes practical methods of employing water as one of the most effective of the known methods to allay dust in bituminous mines.

Jan 1, 1938

By Francis X. Cannaday

The Bureau of Mines developed equipment to measure the sonic velocity of pulses transmitted through rock samples varying in size from laboratory specimens to mine pillars in place. Pulses are produced by electronically excited piezoelectric ceramic transducers. Special equipment components were developed by Bureau facilities; other components are commercially available. The technique permits a nondestructive, repetitive, stable, shaped pulse to be used in place of explosive caps or hammer blows. Longitudinal wave travel time measurements were taken on an oscilloscope screen; transverse wave measurements were taken under special field conditions. Results were consistently repeatable within the accuracy of the oscilloscopes utilized.

Jan 1, 1966

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

By J. W. Walkiewicz

Studies were conducted by the Bureau of Mines to develop a method for fabricating Sm-Co permanent magnets. This method consisted of arc-melting, crushing and grinding the alloy, alining and pressing the powder, and sintering the green compacts. Results indicated that the optimum composition was 36.7±0.3 weight-percent Sm and 63.3±0.3 weight-percent Co. This composition was obtained by blending together Sm2C07 and SmCo5. The maximum values exper¬imentally obtained were MHC = 27.4 kOe, BHc = 7,510 Oe, Br = 7,810 G, and (BH)max = 15.1 MGOe. The optimum sintering temperatures and grinding times for maximum MHc and (BH)max were determined. Lowering the grinding temperature from 0° C to -60° C resulted in a significant increase of magnetic properties.

Jan 1, 1973

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By C. M. Mason

Bureau of Mines studies were made on the sensitivity of several ammonium nitrate-fuel oil (AN-FO) mixtures to bullet impact. The experimental work was done with one military rifle and two high-velocity sporting rifles with a variety of ammunition. For the three rifles used, the order of efficiency in initiating detonation in AN-FO mixtures was 220 Swift >300 Weatherby Magnum >30-&apos;06. The velocity of the bullet was found to be a decisive factor in the initiation. The sensitivity of various materials studied increased as follows: Clay-coated prills with 4 percent oil <fresh surfactant-coated prills with 4 or 6 percent oil <surfactant-coated prills with 4 or 6 percent oil and aged 270 days <crushed prills with 6 percent oil <very low-density, surfactant-coated prills (micronized), with 4 percent oil.

Jan 1, 1963

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By G. R. Palmer

Using a fluidized, countercurrent multiple-compartment ion-exchange (MCIX) column previously developed by the Bureau of Mines, Bureau researchers have successfully extracted uranium from a simulated acidic in situ leach liquor that contained 150 ppm U30s? This successful demonstration of the MCIX system is reported, and the effects of varying the operating conditions on the performance of the system are also examined. Operating the MCIX system with a flow rate of 15 gpm/ft2 and an aqueous-to-resin flow ratio of 200:1, more than 90 percent of the uranium Has extracted, and a resin containing approximately 28 grams U308 per liter was produced. The absorption column used to investigate the operating variables was approximately 18 feet long with a 2-inch ID and was divided into compartments that were 1 foot long.

Jan 1, 1980

By D. E. Shanks

As part of its effort to produce cell-grade alumina from clay, the Bureau of Mines investigated the hydrogen chloride gas-sparging crystallization of aluminum chloride hexahydrate (ACH) from aluminum chloride liquor, to provide information for optimizing the crystallization operation. Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities, particularly phosphorus and magnesium, in ACH crystals are (1) aluminum chloride concentration in the feed solution to crystallization, (2) hydrogen chloride gas flow rate, (3) temperature, and (4) concentration of phosphorus and magnesium also in the feed solution. Parameters 1, 2, and 3 affect crystal formation. The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth. Aluminum chloride hexahydrate of cell-grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt-pct P205 and 0.010 wt-pct MgO. Crystallization temperatures less than 600 C decreased crystal purity.

Jan 1, 1981

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By H. Kenworthy

The objective of this research was to develop methods and determine conditions under which metallic sulfides with lower boiling points than sphalerite may be removed from zinc sulfide concentrates by volatilization. A higher percentage of extraction of lead, cadmium, and germanium than is common in current practice was sought. The investigation, conducted by the Metallurgical Branch of the Minerals Technology Division, Region VI, showed that, under proper conditions, it is possible to remove over 90 percent of the lead, cadmium and germanium as an enriched sublimate. The uses of lead, and cadmium to a lesser extent, are well-known. Although germanium was discovered in 1886 by C. Winkler, commercial use has been achieved only in recent years. The amount consumed per manufacturer unit is so small that the price of germanium may still be quoted by the gram. The electronic industries have been the chief consumer of this semiconductor. Germanium is sold largely to the fabricator as a dioxide for reduction to metal and subsequent processing into wafers for use in diode and triode electronic tubes. Extensive research at Purdue University during World War II led to the first practical use of germanium.

Jan 1, 1952