Search Documents

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By Walter J. Huff

"INTRODUCTION The technical studies conducted by the Explosives Division of the Bureau of Mines have been summarized in a series of publications issued annually for the past 10 years. 3/ The following account covers studies undertaken from July 1, 1944 to June 30, 1945. The work is set forth under a number of main headings to correspond to the organizational structure of the division, the various activities being under the immediate direction of unit chiefs, who report to the author. Specific credit it due to the unit leader and his assistants.Determination of Ignition TemperaturesThe ignition temperature of mixtures of isobutane and air were determined by the static method using a 131-cc. quartz bull. 5/ The results obtained follow: Prevention of Benzene-Air Explosions by Addition of Nitrogen and Carbon Dioxide The elimination or mitigation of the explosion hazards of combustible gases is a part of the work undertaken by the Bureau of Mines in promoting safety. Explosions can be prevented by the maintenance of concentrations that lie outside the inflammable limits. A procedure has been developed whereby the inflammable limits of many complex gaseous mixtures may be calculated in a rather simple manner without requiring toilsome laboratory experiments. This procedure has been outlined in a number of previous publications. 6./ During the fiscal year under review, essential data required for the calculations of complex combustible gas mixtures containing varying percentages of benzene were obtained. Benzene vapor is a normal constituent of many manufactured gases and is widely used in the solvent industry and in the manufacture of high explosives."

Oct 1, 1946

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By J. W. Thompson

RAILROAD GRANT-MDIERALS. Diatomaceous or infusorial earth when found in such quantity and quality as to render lands containing deposits valuable therefor are mineral lands within the meaning of the mining laws and must be excepted from grants to the Central Pacific Railway Company. Central Pacific Ry. Co., In re, 45 Land Decisions, 223, p. 226. RAILROAD GRANT-CLASSIFICATION, If any evidence of minerals is found upon lands within a railroad grant and the showing is sufficient in the opinion of prudent and qualified persons to warrant further exploration and expenditure, with reasonable prospects of success, then the land can not be classified as nonmineral and is not subject to the grant to a railroad company. But where there is no present indication of minerals nor any geological evidence upon which to base a mineral finding, land should not be classified as mineral, or held for further classification and reserved from the railroad's grant, upon the surmise that future prospects might disclose evidences of minerals. Southern PacUl.c Ry. Co., In re, 45 Land Decisions, 326, p. 329. INDEMNITY SELECTION BY RAILWAY COMPANY, Under section 3 of the act of July 2, 1864 (13 Stat., 365), and the joint resolution of May 31, 1870 (16 Stat., 378), the Northern Pacific Railway Company could take coal and iron land within its primary or grant limits. It could not base an indemnity selection upon the claim that certain land was coal or iron in ;;haracter, as such land was not lost to it as part of the grant. But the company was authorized to select other lands in lieu of those lost because of their mineral character, but the word "mineral" did not include iron or coal, and, accordingly, the railroad company was entitled to take coal lands under its indemnity selection.

Jan 1, 1917

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d'Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By Robert B. Hoekzema

The Bureau of Mines and U.S. Geological Survey completed a 4-yr (1979-82) mineral appraisal of the Chugach National Forest (CNF), AK. This report summarizes the Bureau's placer gold studies in the CNF. Placer mining from the mid-1890's through 1982 produced an estimated 133,800 oz of gold, of which two-thirds was produced prior to 1920. As much as 6,800 oz of placer gold was produced from 1979 to 1982. Most production came from Crow, Canyon, and Resurrection Creeks. Five types of placer gold deposits were identified in the CNF: (1) alluvial placers, (2) bench placers, (3) eluvial placers, (4) glacial placers, and (5) marine placers. Placer sampling indicated a potential for gold production from alluvial and bench placers associated with historically mined drainages such as Crow, Canyon, Resurrection, Sixmile, and Mills Creeks and from unmined drainages including the Avery, Kings, Snow, Copper, and Tasnuna Rivers and several smaller streams throughout the CNF. Results of fineness tests indicated that gold from the CNF ranges from 455 to over 950 fine. Subsequent investigations in drainages with anomalous placer sample values also identified previously unknown lode mineralization.

Jan 1, 1986

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By William Seymour, L. D. Schmidt, J. W. Myers, W. T. Reid

"This investigation was conducted by the Bureau of Mines as part of a program of the Solid Fuels Administration to encourage the utilization of anthracite fines, the objective being to determine the practicability of using anthracite fines in the manufacture of packagedThe experimental loss of packaged fuel covered by this report were made at a commercial plant using the Glenn Smith process and ordinarily making packaged fuel from Pocahontas screenings. These lots included several made from straight antimacite mines and others made from various blends of anthracite fines with four different bituminous coals. In all cases an asphalt binder was used. Determinations of the physical properties and the cobustion characteristics o the various samples of packaged fuel were made by the. Bureau of Mines at the Central Experiment Station.The physical tests indicated that a packaged fuel of sufficient strength for ordinary handling can be made from straight anthracite coal or from a wide variety of blends of anthracite fixes with bitunimous coal, using asphaltic binder. However the combustion tests indicated that packaged fuel made from anthracite alone tended to crumble excessively during burning and that as much as 30 to 50 percent of a caking coal may be required In the mixture to produce a block having satisfactory combustion characteristics.The authors wish to acknowledge the. splendid cooperation of Messrs. H. W. Kelly, J. L. Mooney and C. H. Stoss of Columbus, Ohio, who were chiefly responsible for obtaining the materials and making all the arrangements necessary for the production of the packaged fuel for testing.Thanks are due to the officials of Carnegie Institute of Technology for the use of their Olsen. Testing Machine and to H. M. Cooper and W. A. Selvig of the Bureau of Mines for analyses and tests."

May 1, 1946

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946