Search Documents

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By A. C. Johnson

This report describes exploration, development, and exploitation methods, and summarizes costs at the Stormy Day mine, which was discovered in 1941. Several shipments of tungsten ore were made in 1944 to the Metals Reserve Company, Salt Lake City, Utah. The purchase of tungsten by the Federal Government, which began in 1951, stimulated interest in tungsten, and a successful program of exploration with participation of the Defense Minerals Exploration Administration (DMEA) indicated enough ore to warrant development of the property. Development work comprised drifting, crosscutting, and raising. Shrinkage stoping was used for mining the ore. Operations were suspended in October 1956, when the Federal Government terminated its purchase program. Total production of the mine was approximately 20,000 tons of tungsten ore. INTRODUCTION This information circular is one of a series, prepared in cooperation with various mining companies and published by the Bureau of Mines, relating to methods and costs of equipping and developing mining properties in the United States.

Jan 1, 1958

By Peter J. Clarke

The petroleum industry continued to be the most important mineral activity in Bahrain during 1978-79. Revenues generated by the petroleum sector increased from $378 million' in 1977 to an estimated $419 million in 1978 and approximately $522.5 million in 1979, despite decreasing production over the 2 year period. There were two oilfields that produced revenues for Bahrain, the Awali oilfield, the nation's only onshore producer, and the Abu Sa'fah oilfield, located in the Persian Gulf, north of Bahrain, The Await oilfield has been decreasing output from a high of 27,973,000 barrels in 1970 to 19,000,000 barrels in 1979. Bahrain shared the revenues from the Abu Sa'fah oilfield with Saudi Arabia, as settlement of an ownership dispute. For the first time, in 1978, revenues from the Abu Sa'fah oilfield represented over 50% of the total receipts from the petroleum sector. The years 1978-79 saw the gradual takeover of the Bahrain Petroleum Co. (Bapco), formerly a subsidiary of the California Texas Petroleum Co. (Caltex), by the Government-owned Bahrain National Oil Co. (Banoco). By yearend 1978, Banoco owned 60% of Bapco, and Caltex the remaining 40%. The Government-owned company controlled exploration concessions, managed domestic marketing of petroleum products, and controlled natural gas production and marketing. On December 15, 1979, the Bahrain Government completed full takeover of the Bapco operations. Bapco will continue to own and operate the 250,000-barrel-per-day oil refinery located near Sitrah, as well as handle foreign marketing of petroleum products.

Jan 1, 1981

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Southern field is part of the comprehensive study of the mine water problem in the anthracite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8, 9, 10, 11, 12, 15, 16, 18).4 Tim Southern field is in Carbon, Schuylkill, Dauphin, and Lebanon Counties, in eastern Pennsylvania; has an area of 200 square miles; is 70 miles long from Mauch Chunk on the east to the Susquehanna River on the west; and is 1 to 6 miles wide. In the Southern field are 37 underground water pools containing 37312 billion gallons of water (5). Most of these pools overflow to the surface because the barrier pillars controlling them are effective under existent, conditions. Abandonment of mines in the Southern field has resulted in the hooding of 34 percent of the field. The largest tonnage of reserves of anthracite lies in this field, where mining conditions are most difficult. Large reserves of anthra¬cite underlie the abandoned mine workings, and before a great part of these reserves can be developed and extracted, the abandoned workings must be unwatered and kept drained (5).

Jan 1, 1953

By L. D. Tracy

Many bituminous coal-mining companies have inaugurated extensive safety programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania. Story of the Explosion At about 10 o'clock on the night of the explosion an examination was made in No. 2 butt left and parallel off No. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of No. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 13 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air as explosion occurred.

Jan 1, 1927

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By Charles L. Harness

The barite industry has made notable progress since the days when barite was used only as an adulterant in white-lead paints and the only method of mining it was with pick and shovel. The following chronological record may serve to show how this heavy white mineral has grown in importance in the national exonomy and at the same time to indicate development of methods for obtaining it. 1845. - Barite first, mined in Fauquier County, Va., for use as an adulterant in white-lead paints. 1850 (approx.). - French settlers 60 miles southwest of St Louis, Mo., discovered barite; called it "'tiff;' meaning white. It was mined and shipped to St. Louis for use in paint.

Jan 1, 1946

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Rodney D. Rosenkranz

Energy consumption in domes tic copper production has increased nearly 60 percent in the last 10 years, reaching approximately 175 trillion Btu in 1973. Energy required to produce 1 pound of copper rose from nearly 41,000 Btu in 1963 to nearly 50,000 Btu in 1973. Production from lower grade ores and strict pollution control regulations have contributed to this increase. Each stage of copper production has been analyzed to determine total energy consumed, energy mix required, cost of the energy, and recent or proposed changes in operations which may affect the consumption of energy by the copper industry. Data have been gathered from a recent Bureau of Mines canvass of the industry, from visits to copper operations, and from conversations with copper industry officials.

Jan 1, 1976