Search Documents

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Hongchun Lou, Yan Zhang, Xianjun Lu

"The potential of Fe(NO3)3 modified attapulgite was assessed for the adsorption of phosphorous removal from aqueous solutions. Natural attapulgite was modified by Fe(NO3)3, and thus the composite adsorption materials could be obtained. Also phosphorous adsorption characterization on the iron-coated attapulgite was investigated in this research. Taken overall the results suggested that phosphorous adsorption capacity could be improved markedly by adopting ferric modified-attapulgite. The optimum phosphorous adsorption were developed in the experimental conditions of the solid-to-liquid Ratio 1g/L, the initial phosphorous concentration 5 mol•L-1, reaction time 120 min, temperature 25 ? and pH=4.0, the removal efficiency is 92.28% for the modified attapulgite. In comparison of batch experimental results of phosphorous adsorption onto natural and iron-coated attapulgite, it has provided much more likely the same change trend. On the other hand, the outcomes of this analysis indicated that ferric modified adsorbent was notably influenced by adsorption element over natural attapulgite. The Freundlich isotherm adequately described the adsorption course of phosphorous onto ferric modified-attapulgite with the correlation coefficient R2 goodness of fit of 0.9690."

Jan 1, 2014

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003

By Claudio L. Schneider, Reiner Neumann

Any serious study of stereological conversion procedures must be based on an as accurate as possible complete fractionation of a real mineralogical texture. The original work on the Dolomite- Sphalerite Magstream? separation provided excellent data for establishing a working stereological conversion procedure, which has been successfully applied to a number of ores since its implementation. The linear grade distributions measured from these fractionated particles have been published and are accessible. The procedure for stereological conversion from areal measurements is exactly equal to the procedure for linear measurements. Particle composition from the dolomite-sphalerite density-fractionated particle sets, derived from both linear and areal data (Figures 1 and 2, respectively) are redundant, after proper transformation, and match the particle’s compositional range (plotted against S.G.) expected from Magstream?; direct density measurements by Hemicropicnometry plots within the ranges. Linear data cannot be used without conversion, but areal measurements are often directly applied as liberation spectra. Our areal measurements, without stereological conversion (Figure 3), differ completely from the results after transformation, and its density range falls mostly out of the expected/measured values. Therefore non-transformed areal data cannot be directly applied as useful liberation information.

Jan 1, 2003

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By S. K. Pan, M. P. Srivastava, N. Prasad

"Dalli mines of Bhilai Steel Plant, India is fully mechanized iron ore mine having wet processing system. It has a capacity to treat 5 Mt of ROM. In processing circuit of Dalli mines, scrubbing, wet screening and classification operation is being carried out. Average slime generation for the last five years is about 14% of ROM. As the mining has reached to the lower benches, fines generation is more. As a result, very fine and heavy particles, which settle fast, are being discarded with the slime to tailing pond. These heavy and faster settling particles were causing jamming in the thickeners.Laboratory investigations were carried out at Research and Development Centre for Iron and Steel (RDCIS) to suggest a suitable scheme to recover high quality fines so that the availability of thickener can improve. The slime samples were first treated in a floatex density separator. The concentrate obtained from the floatex density separator was treated in hydrocyclone. Laboratory investigations indicated that the slime with 49% Fe, 12.7% silica and 10.7% alumina can be upgraded to 62.1% Fe, 3.3% silica and 2% alumina with 36% material recovery. Based on the laboratory studies ,a system was installed at Dalli minesThe general arrangement of the system is shown in Fig. below."

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By Williams Calderon, César Arredondo, Gonzalo Montes-Atenas

The quality of final concentrate in froth flotation circuits is largely dictated by the correct implementation of the froth washing operation in flotation cleaning stages, which are commonly installed in column flotation cells. In flotation plants, this aspect has been largely overlooked and the froth washing is restricted to the use of perforated piping through which process water flows producing a similar effect to that observed in "fountains": jet created with low energy crosses the froth phase washing out entrained particles as well as particles weakly attached to bubbles. The aim of this research study is to assess the efficiency of traditional froth washing systems theoretically and experimentally. A theoretical model was implemented using Fluent® software where a jet of variable speed was introduced in a continuous soft matter phase with physical properties similar to those observed in a froth phase in wet and dry conditions. In addition, a simple experimental protocol was designed to validate the model. It was found that the water process jet-like flow influences the behavior of 2 to 3 times the equivalent volume in the froth phase. Such influence zone is dramatically reduced as the froth phase becomes drier. These results were confirmed by the experimental findings indicating that a better froth washing technologies must be assessed and implemented. Some aspects of the ideal froth washing system are derived and discussed in details.

Jan 1, 2014

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By M. Schneider, J. Regler, Th. Neesse, AKW A. + V GmbH & Co., J. Dueck, F. Donhauser

"In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.As can be seen from Fig. 1, the hydrocyclone battery has been modified for regulation purpose. The battery was manufactured with an overflow collector as a closed pressure chamber (1) with a discharge pipe (2) where the throttling valve (3) was installed.With increased stepwise throttling of the overflow, the volume split is changed with the effect that the solids discharge in the underflow is increased. To stabilize the total throughput, the feed pump speed is simultaneously increased so that the pressure drop ?p across the hydrocyclones (9) remains approximately constant. However, this causes the increasing pressure inside the hydrocyclones, which results in a further intensification of the underflow discharge. After the detection of the break through of the air core (transition state) by the capacitive sensor (4), the throttle valve is shortly opened, and a new regulation interval can start again. The control concept is focused on maintaining the optimum operating state, characterized by the underflow discharge shape at the transition state between rope and umbrella discharge."

Jan 1, 2003

By Ayumu Tokumaru, Shuji Owada, Gangfeng Liu

"Several million spent catalytic converters are disposed annually worldwideandeach containing about 0.5-1g ofplatinum and 1-2g of all the platinum group metals (PGMs), then,it is fairly significant to recover PGMs from the spent automobile catalyst. The PGMs’ recovery is a proven technology, including pyro-and hydrometallurgicalmethods, and the highestrecovery can achieve approx. 98 wt.% by acid-leaching method, but theserecyclingtechnology seems to be too highlyenergy-consuming. SincePGMs aredistributed only in coat layer in spent catalyst, it is of great significance to enrich the coat layerwith some physical methods as a pretreatment.In this paper, according to the double-deck structureof the catalyst andthe different properties of the two main compositions, alumina-ceria phase of coat layer and cordieritephase of substrate, the concentration of the coat layer was investigated by combiningthree kinds of physical separation technologies, heating-quenching, crushing and surface grinding. In the first stage, thermal stresscouldgeneratebetween the two phasesby thermal expansion difference,to producefracturesin the thinnest part of coat layerand micro-cracksin coat layerand at the interface of coat layerand cordierite substrate. The second stage of crushing, by jaw and roll crushers, could break dominantly the coat layer and the third stage of surface grinding, carried out by attritor, promoted further separation and concentration of coat layer fromthe substrate.We also improved the attritor grinding by adding a new lift-arm to the cell for achieving better mobility of sample particles in the selective surface grinding."

Jan 1, 2014

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980.s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão - GO), Bunge (Cajati - SP), Fosfértil (Tapira - MG) and Copebrás (Catalão - GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Kosuke Nishioka, Yasushi Kihara, Altansukh Batnasan

The aim of this study was to investigate the feasibility studies of seawater in flotation of a 1.5 mass % of copper containing copper sulfide ore. Effects of seawater, various frothers, and different distilled water/seawater ratio on flotation of copper sulfide ore were studied. Surface properties of native copper ore and sea water soaked were examined by using FT-IR spectrometry. Chemical contents of the copper sulfide ore and after flotation were identified using XRD studies. XRD pattern showed that the main constituents of the copper sulfide ore are chalcopyrite (CuFeS2), bornite (Cu5FeS4). Flotation experiments were carried out using mechanical agitation flotation equipment with a mineral separation type flotation cell. Froth flotation experiment was conducted using calcium hydroxide was used as a pH adjuster, using methyl isobutyl carbinol (MIBC), dow froth 250 (DF 250) as frothers and potassium amyl xanthate (PAX) as collector for the copper recovery from the copper sulfide ore containing chalcopyrite and bornite. The results showed that the copper recovery by flotation was dependent on the flotation medium and frother. The main results showed that the copper recovery by flotation was dependent on the process water and frother. The copper recovery reached 97 % and 87 % in the distilled water flotation and seawater flotation with MIBC, respectively. For seawater flotation with DF 250, the Cu recovery achieved near 95 % and grade of Cu in the froth product after 5 min flotation was reached 29.8 mass %.

Jan 1, 2014

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014