Search Documents

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By Kati Tschöpe

Cathode wear has become an increasing challenge in the aluminum industry due to the use of more graphitized materials. Today, there exist no standard laboratory methods for measuring cathode wear where different commercial materials can be ranked. The typical average wear rate in an electrolysis cell is quite small. The aim of this work was to design a test method where the wear could be accelerated compared to industrial cells. It was focused on polarized tests where the cathode is exposed to electrolyte, which gives higher aluminium carbide solubility. The cathode materials were characterized by microscopy and image analysis.

Jan 1, 2011

By P. L. Schwartz

The present method of shipping potash to the myriad of consumers is inefficient, not only because of the extreme and unpredictable nature of seasonal demand, but also because railway car turnaround times are very lengthy. The Floating Train system employs unit trains of potash operating from Saskatchewan mines to distribution warehouses located throughout the six corn-belt states of Minnesota, Iowa, Wisconsin , Illinois, Indiana and Ohio, transshipment points at Thunder Bay and the U.S. waterway network, and, where applicable , large consumers. These unit trains would "float", meaning that they would not originate at the same mine nor terminate at the same warehouse on each trip . They would " float " freely among the origins, destinations and participating railways. The potash would be shipped uniformly throughout the year and usually stored in warehouses located within the six states. It would be subsequently delivered to consumers within a 75-mile radius. Distribution warehouses and rolling stock would be provided by a new company, Potash Distribution Limited, consisting of major potash producers and the Canadian railways. Potash Distribution Limited would be responsible for the distribution of potash from the origin through the warehouses to the final consumer. The additional costs of providing warehouse space and outbound delivery will be offset by the reduction in both rail rates and "peaking" expenses.

Jan 1, 1978

By Garnet T. Page

"ABSTRACTThese societies •can help in such aspects of a vocation.al guidance program in secondary schools as: provide vocational and technical information, and assist with vocational exploration, such .as plant visits, films, etc. -as .an aid to the student in making a self-inventory. Evidence is increasing that employers' needs for engineers and scientists will not be adequately met in the future. Therefore, the E.I.C., C.I.M., .and C.I:C. recently revised and extended the activities of the Canadian Counselling Committee on Engineering and Science. This co-•operative .action is to be integrated with the educational system, nationally .and locally, and with provincial associations •of engineers and other groups interested in the provision of vocational information in engineering and science.DEFINITIONTHE scientific treatment of any subject requires consistent use of carefully defined terms. The National Vocational Guidance Association of the United States studied the problem of the definition of vocational guidance for .about 16 years, and in 1937 finally arrived at:""Vocational guidance is the pro-cess of assisting the individual to choose an occupation, prepare for it, enter upon and progress in it. It is concerned primarily with helping individuals make decisions and choices involved in planning a future and building a career -decisions and choices necessary in effecting satisfactory vocational adjustment.""RANGEAs a school enterprise, vocational guidance begins at that point in the individual's life when he finds it necessary to make choices that have a definite significance for his future vocation."

Jan 1, 1952

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By W. D. Robson

THE prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first (1) was published in 1937; the second (2), in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research. HARMLESSNESS OF ALUMINIUM Animal experiments having served their purpose, it became necessary to consider means to test the discovery on humans. A question for immediate consideration was: Is aluminium harmful to man when inhaled as a fine powder? While the animal experiments were reassuring, since they conclusively showed the powder to be innocuous when breathed by animals, it was, nevertheless, desirable to have additional reassurance with regard to its effect upon human beings. Through the courtesy of the Aluminum Company of America and especially the valued interest in this problem displayed by that Company's Director of Research, Dr. Francis C. Frary, a study was made of the records pertaining to the health of a group of 125 employees who had for many years been engaged in the manufacture of finely powdered, metallic aluminium for the paint and ink industries. The conditions were such that these employees had inhaled varying and oft-times very dense concentrations of this powder daily over periods ranging from 6 to 23 years, the average for the group being 12 years. X-ray pictures of their chests showed no abnormalities attributable to aluminium. Their general health seemed better than that of the 3,000 workers in other sections of the plant. In fact, the early films of three employees in this group of 125 showed shadows suggestive of minimal tuberculosis, which shadows were not discernible in films taken after considerable periods of exposure to aluminium powder. The harmlessness of aluminium was, by this study, reasonably well established at the outset, a finding subsequently verified by Ontario research on humans.

Jan 1, 1944

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By R. C. Rowe

DR. W. F. GRAY (Contributed discussion, presented at meeting by Mr. S. C. Mifilen): Mr. Rowe's suggestion that the Institute should organize itself to interpret the needs of the mining industry to federal and provincial mines departments should commend itself to our membership as sensible and practical, and as one which these public administrative bodies may welcome. One has to start with the premise that those who head the departments of mines in question have the welfare of the industry at heart. Also, it must be postulated that the technical viewpoint of our membership is necessarily free of political considerations. With these reservations, one ventures to state that both Mr. Rowe in his communication to the present session of the Institute, and Professor M. Y. Williams in his earlier communication to the Western Meeting, on The Geological Survey and Mining Development (1), voice the regret general among our membership at the abandonment of the honoured name, and to some extent of the status, of the Geological Survey of Canada. The writer, in 1932, devoted his Presidential Address to the Institute to an appreciation of the value to Canadian mining of the Geological Survey of Canada (2), affirming the desire of the Institute "that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country will permit, because, to scrimp expenses on the Survey, is 'to save at the spigot and lose at the bunghole'." He believes that is still the opinion of the Institute, and, if contraction of the usefulness of the Survey is feared by our members at this time, it is incumbent upon the Institute, in fairness to those who direct our government, to say so in precise and explicit terms. Mr. Rowe puts the situation pithily when he writes: "We have reached a stage in our development where a stock-taking and co-ordination of existing knowledge and data is essential. This is a part of that basic function of Dominion mineral technical services which is national and not provincial in its scope".

Jan 1, 1939

By Jas. E. Thomson

"The Kirkland Lake-Larder Lake gold area is in northeastern Ontario and is a continuation of the ore-bearing belt that extends across northwestern Quebec through the Rouyn, Cadillac, Malartic, and Bourlamaque areas. It is the oldest mining camp along this famous mineral belt. Gold discoveries were first made at Larder Lake and Swastika in 1906, but it was not until 1913 that important developments at Kirkland Lake created a real interest in the country. Total gold production of the camp passed the million dollar a year mark in 1920 and increased in amount yearly until the advent of the second World War when there was a falling off due to labour shortage. The Kirkland-Larder camp ranks as the second largest gold producing area ' in Ontario. To the end of 1944, twenty-two mines in the area had produced bullion valued at $515,631,428 and ten mines had distributed dividends amounting to $205,981,116. The average grade of the ore milled in this period has been $15.17 a ton for the mines in the Kirkland Lake area and $6.49 a ton for the mines at Larder Lake.ROCK FORMATIONS OF THE AREAIn a general way the rocks of the country may be divided into the lithological groups indicated on the accompanying geological sketch map. This map has been compiled largely from recently issued geological sheets of the Geological Branch of the Ontario Department of Minest. Owing to the present difficulty of separating the formations of the Larder Lake country into the twofold age divisions of Keewatin and Timiskaming, the usual custom in the past, a lithological grouping of formations has been adopted. The age terms 'Keewatin and 'Timiskaming' are loosely used in this article to express the often used but not necessarily accurate distinction between the main groups of older strata."

Jan 1, 1954

By Michael J. Rosko

Methods have been developed for processing and analyzing reflected solar radiation data obtained by Landsat 5 Thematic Mapper multispectral scanner. Spatial resolution for the Landsat series satellites is 30 meters per side per pixel. Materials on the Earth?s surface absorb or reflect different parts of the electromagnetic spectrum depending on their physical and chemical properties and, therefore, typically have characteristic spectral ?signatures?. Using these signatures, environmental parameters such as surface water and vegetation may be identified and analyzed. Principal advantages of the satellite image method for environmental monitoring include: a relatively long historic period beginning in 1985 for which information is available, the reliable numerical basis for the results, and the ability to assemble a historic environmental baseline and provide on-going monitoring for large or remote areas where standard monitoring methods may not be practical. However, because the long-term continued operation of Landsat 5 is problematic due to the age of the equipment, QuickBird and IKONOS satellite images were processed to determine if the two systems are sufficiently similar in their results to allow continuing monitoring using QuickBird data. The QuickBird satellite was launched in 2001 and collects the same visible and near infrared spectral bandwidths as Landsat 5, allowing for equivalent process algorithms for QuickBird, IKONOS, and Landsat 5 data. Spatial resolution for the QuickBird images is 2.4 meter per side, allowing for more detailed characterization of the land surface; spatial resolution for the IKONOS images is 4 meter per side. Because of several differences between the satellite systems, including degradation of the Landsat 5 sensor, it is necessary to calibrate QuickBird and IKONOS results to the Landsat results to verify similarity. Recent images from the satellite systems have been processed and results have been compared to determine the validity of comparing Landsat 5 and QuickBird/IKONOS images so that these newer data can be used reliably in the future instead of Landsat 5 data. Results from this comparison are presented in this paper and suggest that analyses for vegetation using the two satellite systems are comparable, and that little calibration is required. Results from comparison of surface water results from the two systems are less comparable and is currently being investigated by the authors.

Oct 1, 2009

By Gerry Roblesky

"IntroductionWestar Mining Ltd. is Canada's largest producer of metallurgical coal for the export market. It currently operates two mines, the Balmer Mine at Sparwood, British Columbia producing 6 000 000 tonnes per year and the Greenhills operation at Elkford, producing 2 100000 tonnes per year. Approximately 1600 people are employed between the two mines which operate independently but share common administrative services.Like most mining companies in Canada over the past three or four years, Westar has faced rising production costs along with flat or declining prices and demand for its products. In order to survive under these conditions it has become necessary to strive for decreased costs in any way possible. Over the past two years there has been a widespread introduction of microcomputers across the company. In order to satisfy increasing demand for accurate and pertinent information while at the same time increasing productivity, the microcomputer has become an invaluable tool.This paper describes some of the problems faced by a mine maintenance department in this operating climate and how they were solved with the help of a microcomputer. It also describes some of the problems that may be encountered both with equipment and people and recommends some ways that these might be minimized or avoided. Finally, an assessment of whether or not the move to microcomputers was a current and economical one, and a brief description of future plans and projects is given.The Maintenance OrganizationIn order to appreciate fully the role that microcomputers are playing within the Maintenance Department at Westar Mining, a little background on the organization and operating philosophies is in order. Most of the comments apply directly to the Balmer operations, however, the Greenhills operation is similar in concept.The mine maintenance organization operates on a fleet based concept with these departments reporting to the maintenance superintendent: haulage trucks, shovels and drills, loaders and Caterpillar equipment, maintenance services, and rebuild services.Each of these departments is headed by an assistant superintendent and is responsible for all maintenance on the equipment on the respective fleet. Shift foreman, planners, specialists and clerical staff are assigned to each fleet. A central engineering and administrative group consisting of one engineer and three clerical positions is responsible for maintenance engineering and centralized administrative services"

Jan 1, 1988

By W. Gan

The interactions between bitumen and quartz sands in aqueous solutions were studied with the objective of recovering residual bitumen from Athabasca oil sands froth treatment tailings. It was observed that the presence of various multivalent metal cation (Fe3-, Fe2+, Mg2+,Ca2+, etc.) increased the mutual coagulation between quartz particles and oil or bitumen droplets within certain pH ranges. While the increased coagulation was detrimental to the recovery of the bitumen since it lowered the degree of bitumen liberation from sands, this effect could be reduced or eliminated by the addition of organic chemicals such as citric acid, oxalic acid and EDTA. Among these organic chemicals, citric acid was found particularly effective even at very low concentration.

Jan 1, 2006

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013