Search Documents

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By Fidelis T. Suorineni

The conditions for rockburst occurrence are traditionally identified as: high stress, high extraction ratio, strong brittle rocks, folding, faulting, and unfavourable excavation geometry. Based on a critical review of case histories, this paper identifies oblique loading of orebodies by the major far field principal stress as a cause of rockbursts. Orebodies subjected to this loading condition are termed orebodies in shear. Orebodies in shear are subjected to compressive and shear loads. The case histories presented unambiguously show that the magnitudes of the far field principal stress alone, and a knowledge of the conventional rockburst causing factors are not sufficient for mine planning and design. The orientation of the major far field principal stress, or for that matter the driving stress relative to the orebody axis, should be recognised as one of the causes of rockbursts. It is suggested that since stress orientation is an important factor, and orientations from stress measurements are so variable, orientations from stress measurement data be complemented with underground observations from borehole and excavation breakouts to determine the actual in situ stress orientation, whenever possible. Also stress modelling for the design of critical elements (pillars) should include a sensitivity analysis on the relative critical field stress direction. The paper emphasises that special attention should be paid to or

Jun 1, 2012

By R. S. Fitzpatrick, P. Hegarty

"Gravity separation is a key technology in the recovery of a range of mineral ores including coal, tin, tungsten and tantalum. One of the problems associated with gravity concentration is that recovery is traditionally lower than for other separation techniques such as the flotation of base metals. Any improvements in recovery will, therefore, have a significant effect on the economics of operations of this type. More accurate, robust modelling of gravity separators is one means of achieving greater recoveries. Furthermore, better modelling can lead to more informed equipment selection and process design for potential economic deposits.Previous models for gravity separation equipment have typically relied on simple metal mass balances from samples of the separated products. However, with advances in technology there is a ready availability of analytical instruments for the automated quantitative determination of mineralogy. Instruments such as the Mineral Liberation Analyser and QEMSCAN make it possible to estimate particle size and density (related to mineral liberation and association) which are the primary factors in gravity separation. Models produced using quantitative mineralogy of feed streams will be potentially superior to those produced historically.This paper describes test work undertaken on a wet shaking table using a synthetic ore. The objective of this test work was to develop a model to predict the effect of changes in feed ore characteristics on shaking table performance by measuring quantitatively the mineralogy of the feed material. Particles were divided into size/density classes based on the results of QEMSCAN analyses.It was found that it was possible to use data from QEMSCAN to predict the recovery of size/density classes and to predict the effect of changes in the relative abundances of these classes on the separation. This model can potentially be used to adjust operating variables to maximise grade and recovery by monitoring the input feed. Care was needed when utilising QEMSCAN data to ensure representivity."

Jan 1, 2016

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By Rodrigo Serna-Guerrero, Ted Nuorivaara

"As the demand of raw materials increases in a global scale due to demographic and economical changes, it is necessary to find technological solutions that improve current production processes in an efficient and sustainable manner. The main objective of this preliminary study is to evaluate the properties of foam produced with a cellulose-based molecule as an alterative to commercial frothing agents in flotation operations. There are two potential advantages identified with the use of cellulose-based additives for the proposed application: i) these chemicals can be produced from sustainable sources (i.e., non-edible crops), and ii) cellulose can be functionalized with chemical groups, in order to rationally modify its behaviour. In previous studies dealing with foam stabilization, it has been proposed that some functionalized cellulose species present a self-assembly mechanism at gas-liquid interfaces. Unlike typical surfactant-based frothers, cellulose molecules form networks around the bubbles that act as protective layers to the mechanical stress and to the occurrence of ionic species. This work studied the properties of foams produced in the presence of a partially hydroxylated cellulose molecule (i.e., hydroxypropyl methyl cellulose; HPMC) under various concentrations in a laboratory-scale column. A comparison with a commercial surfactant frother (i.e., Nasfroth 240) is presented, and a rationalization of the behaviour of HPMC in terms of foam properties (i.e., surface tension, bubble size, foam depth) is proposed. INTRODUCTIONThe search for green alternatives to chemicals produced from non-renewable sources has become a topic of major relevance in industry (Choi et al., 2015). As a chemical consuming industry, the mining sector faces now the challenge of adopting new processing technologies and strategies in order to achieve the future demands of sustainability. Evidently, a move towards green chemistry can only take place by identifying substitute molecules offering potential advantages in terms of recovery and grade."

Jan 1, 2016

By K. Fagerlund, L. Rosenback, T. Mäkinen, Y. Anjala

This paper deals with the nickel smelter and refinery concepts Outokumpu has applied at Harjavalta and several other plants. Also other process routes and modifications developed and tested by Outokumpu during the recent years are highlighted. Outokumpu started nickel production in Harjavalta in 1959. Until 1995 the Flash Smelting - Peirce-Smith (PS) converting route was applied. High grade nickel matte from the converting step was further refined by means of leaching and electrowinning to produce cathode nickel. In 1995 the nickel production capacity was increased from 17 000 t/a to 52 000 t/a based on the Direct Outokumpu Nickel Smelting Process (DON). In the DON process PS converting is eliminated and high grade nickel matte with low Fe-content is directly produced in the flash smelting furnace (FSF). Metal values from the smelting slag are recovered in the electric furnace (EF) as iron containing Ni-matte. The DON process can be operated with either two matte concept, where high grade FSF matte and EF matte are produced, or a single matte concept, where EF matte is recycled to the smelting furnace and thus only one type of high grade matte is obtained. The additional refinery capacity at Harjavalta is based on hydrogen reduction producing.

Jan 1, 2005

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By Martin P. Raffield

Placer Domes? Campbell Mine, situated in northwestern Ontario, is undergoing an assessment of the efficiency of the operation which is necessitated by the low gold price and a reducing ore reserve grade. A decision has recently been taken to move away from a functional based departmental structure (underground, engineering, geology, etc.) towards a team-based system where crews, engineers, geologists and supervisors are responsible for the planning and operation of a particular area of the mine. The objective is to improve communication and understanding of the goals and achievements and to ensure a forum is available for the generation of ideas. It is intended to increase the accountability and decision-making ability of the teams in an effort to achieve the mines? safety and production targets. This paper presents a critical review of the progress of this organisational change process and its successes and failures at the time of writing.

Oct 1, 2001

By J. Erik Scheel

Overview ? About Hard Creek Nickel ? Turnagain property ? Proposed power line ? Recent Preliminary Assessment ? Favourable economics ? Property Geology ? Mineralization and metallurgical characteristics of major lithologies ? Development of the acNi (ammonimum-citrate H2O2) technique ? Overview of necessary steps ? Results of the technique ? Conclusions

May 1, 2008

By Éric Côté

Introduction The 425 Main Ore Zone ? Block of ore partially mined in the late sixties; ? Area was sealed off for over 30 years due to SO2 emissions from oxidizing fill material; 425 Project goal ? Bring the zone back into production without jeopardizing the mine; ? Minimize risks associated to SO2;

Feb 1, 2008

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today's competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By Javier Ramirez

"Recent R&D pilot plant testing was done to validate a full industrial scale system for recovering residual magnetite from the tails of an iron ore concentration plant. The recovery system is based on an autogenous heavy media separator treating a tailings slurry at 0.45% solids by weight. A 3,100 m3/h capacity concentrator was installed based on the testing findings. Excellent metallurgical results have been observed in two years of continuous operation. This experience is the basis for the proposal of a novel process consisting of the preconcentration of base metals ores; the idea being to obtain a heavy bulk concentrate of the polymetallic minerals and discarding in one step the light gangue mineral components. The bulk concentrate then proceeds to conventional froth flotation. The reduced volumetric flow of the bulk concentrate allows a reduction in the size of the subsequent flotation circuit. A prerequisite for the heavy media separation is a fine size grinding of the ore and a correspondingly high degree of liberation of the mineral species to be recovered. A process scheme is also presented in which the gravity concentrator works in conjunction with a companion tailings thickener for process water recovery. The underflow from this thickener, having paste consistency, can be sent to a tailings dam or mixed with Portland cement for mine backfill. The process water in the system is managed at an estimated recovery in excess of 98%. Additional R&D work using this novel approach is being considered by a large iron ore concentrator for removal of liberated silica from the final concentrate; and for upgrading 3.5 million tons of a marginal hematite reserve owned by the mining company.INTRODUCTIONGravity preconcentration (static and dynamic) of sulphides prior to froth flotation has been and is being practiced at various concentrator plants (Asarco´s Young Mill: heavy media cone; Mount Isa: DSM cyclone; Afton Mines: Denver jigs; Tsumeb Mine: Reichert cone) (Burt, 1984). The idea behind installing preconcentration equipment is to reduce the volume of feed processed on flotation, thus requiring smaller flotation plants although other advantages may be of importance, such as obtaining richer concentrates due to higher grade feed, better process water and energy management, and reduced flotation reagent consumption.The SedconTM solid/liquid separator is a versatile process unit patented in Mexico (MX/u/2007/000305). As a gravity device, it may be classified as an autogenous heavy media dynamic concentrator. Figure 1 depicts the Sedcon (Sedimentador de conos) separator. The four main components are as follows: the feedwell for efficient mixing of the pulp with dilution water and flocculant (and coagulant for water clarification); the inner cones (passive elements for solid/liquid separation); the discharge underflow cone; and the scraper mechanism. The standard discharge cone is a 60° inclined cone for general applications. For paste tailings thickening applications, a deep cone with a 69° inclined cone is used."

Jan 1, 2016