Search Documents

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminicki, D. Evans-Lamswood

"Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite. La caractérisation systématique de la minéralogie des gîtes de sulfures massifs peut fournir des indications précieuses sur la genèse des minerais et le traitement métallurgique qui ne seraient pas disponibles par d’autres méthodes. Nous décrivons un procédé par lequel (1) un algorithme est utilisé pour calculer l’abondance de minéraux normatifs à partir d’analyses lithogéochimiques, (2) les résultats sont exprimés dans des blocs diagrammes, (3) les résultats sont par la suite validés par analyse d’image automatisée sur un microscope électronique à balayage en électrons rétrodiffusés et par cartographie en rayons X sur des échantillons constitués de grains montés en résine, et (4) les résultats de cette validation sont combinés aux données texturales obtenues par microscopie optique.Cette technique est appliquée aux sulfures magmatiques de Ni-Cu-Co du gisement Ovoïde, en utilisant les analyses géochimiques de 3175 échantillons de roche totale. L’Ovoïde comprend trois types de minerai. Le type I est situé au centre du gisement; il est riche en magnétite et pauvre en pyrrhotite avec des quantités intermédiaires de pentlandite et de chalcopyrite. Le minerai de type II entoure le minerai de type I et est riche en pentlandite et en chalcopyrite avec des quantités intermédiaires de pyrrhotite et de magnétite. Le minerai de type III se trouve à la base ainsi qu’à bordure externe de la partie nord du gisement; il est riche en pyrrhotite et pauvre en chalcopyrite, avec un contenu intermédiaire en pentlandite et une quantité faible à moyenne de magnétite."

Jan 1, 2012

By R. Plassart, F. Laigle

"As a powerhouse, a transformer or a valve chamber, large underground caverns are a major element of hydropower plant. On the contrary to galleries and shafts which are linear and long underground structures, large caverns are designed with often complex geometries and large spans. Moreover, as these caverns are generally located on the foot of the hydraulic scheme, the high overburden is often responsible of a high stress state. Thanks to current experiences in France and around the world, the Hydro Engineering Centre (CIH) of EDF has defined great principles in the design of caverns leading to a more general methodology. The project of Tehri in India is an example of difficult ground, with in the same time a high overburden, a ductile material and an important schistosity. These physical realities are attempted to be approached in numerical modelling thanks to a constitutive law with softening behaviour and an oriented criterion integrated in the continuum model. As a result, a flexible support is advised, based on a high density bolt system and a thin lay of shotcrete. This methodology has been developed in the case of Gilboa in Israel, except the schistosity which has not been observed in situ. At last, the example of Gavet (France) illustrates a discontinuous case of numerical modelling for a good quality but fractured rock mass.PRINCIPES ET METHODES DE CONCEPTION DE GRANDES CAVERNESHYDROELECTRIQUES SOUTERRAINESRESUME Les grandes cavernes souterraines abritant les turbines, les transformateurs et certaines vannes sont des ouvrages majeurs dans les aménagements hydroélectriques. A la différence des galeries et des puits qui présentent de longs linéaires, les grandes cavernes sont des structures à la géométrie souvent complexe et avec des portées conséquentes. De plus, ces cavernes étant généralement situées en pied du circuit hydraulique, la grande couverture rocheuse peut se traduire par un état de contraintes important. Forte de ses expériences récentes en France et dans le monde, le Centre d’Ingénierie Hydraulique d’EDF a identifié de grands principes de conception des cavernes permettant l’élaboration d’une méthodologie plus générale. Le projet de Tehri en Inde est un exemple de terrain difficile, présentant à la fois une forte couverture, un matériau ductile et une schistosité marquée. Ces réalités physiques sont approchées au mieux grâce à la prise en compte dans les modélisations numériques d’une loi de comportement radoucissante avec un critère orienté intégré dans un modèle continu. Les résultats ont conduit à privilégier un soutènement souple basé sur un boulonnage systématique relativement dense associé à une fine couche de béton projeté. Cette méthodologie a ensuite été reprise pour le projet de Gilboa en Israël, exception faite de la schistosité puisque non observée sur site. L’exemple de Gavet (France) enfin permet d’illustrer un cas de modélisation numérique discontinue d’un massif rocheux de bonne qualité mais fracturé."

Jan 1, 2015

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

This paper aims to increase our understanding about existing capacity-building approaches and their implications for obtaining a social license to operate in the mining industry. The notion of ?capacity building? is gaining increasing currency in the mining sector in developing countries due to a rapid rise in the globalisation of mining operations. Capacity-building is conceived here as a process that lasts after the mine-cycle, intended to provide local mining communities with tangible skills and knowledge to gain meaningful employment in mining or other industries relevant for the local economy. Building community capacity to understand and effectively respond to these transformations is vital for obtaining a social license to operate, as it promotes sustainable and locally relevant development. Accountability mechanisms such as global norms and international standards increasingly highlight the need to build capacity among stakeholders, particularly among local communities adjacent to mining operations. International frameworks and mining companies have embraced the notion of capacity-building as a driver to assist corporate social and operational performance. However, this narrow understanding of capacity-building through the prism of corporate social responsibility and ?best practice? is preventing the industry from meaningfully impacting communities and maintaining a social license to operate. This latter notion is being widely embedded across multiple industry sectors, as a social and economic reward from mining companies to compensate communities for natural resource extraction and gain social acceptance. Although both concepts are widely recognised in the minerals industry, insufficient attention has been paid to the implications of applying a top-down (mining-orientated) or a bottom-up (community-orientated) capacity-building approach for obtaining a social license to operate, or indeed how these two concepts are linked and applied in practice. At times, communities lack the necessary capacities in the form of education and skills to deal with mining-led livelihood transformations. This is preventing both mining companies and communities from forging sustainable livelihoods and responding to mining-led livelihood transformations, a situation that is creating discontent among communities and reducing the possibility of obtaining and renewing a social license to operate for the industry. Based on a review of current scholarly debates, accountability mechanisms in the mining industry and fieldwork findings in Colombia, this paper will contribute to an understanding of the implications of existing capacity-building approaches that support a social license to operate.

Aug 1, 2013

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By Kenneth Williamson

La découverte de nouveaux gisements métallifères constitue le point de départ du développement de l'industrie minérale. Or, au cours de ces dernières années, le nombre de ces découvertes a fortement diminué dans les territoires classiquement explorés, entraînant une recrudescence de l?exploration dans les terrains géologiques de grade métamorphique élevé (e.g., Province de Grenville, Grand Nord du Québec). Ces derniers ont été traditionnellement considérés comme stériles à cause (i) de la monotonie apparente des gneiss qui les composent, (ii) de la difficulté d?identifier leurs protolites, (iii) des changements importants dans l?apparence des gîtes recherchés reliés au fort degré de déformation et de métamorphisme et (iv) des théories qui prônent un lessivage important des cations et des métaux d?intérêt économique par les processus de déshydratation des roches lors du métamorphisme régional (Weaver et Tarney, 1985; Vokes, 2000). Cependant, l?avancée des connaissances dans la compréhension des gîtes métallifères et de leurs terrains hôtes gneissiques intensément métamorphisés, montre que les systèmes géochimiques des roches altérées demeurent robustes (p. ex. ; Trägårdh, 1991; Craig et Vokes, 1993; Geringer et al., 1994; Schandl et al., 1995; Zaleski et Peterson, 1995; Vokes, 2000; Blein et al., 2003, sous presse). Bien sûr, les sulfures peuvent être localement remobilisés et même fondre, mais cette remobilisation n?implique pas forcément la disparition du gîte hôte (Williams, 1990) et peut s?avérer, bien au contraire, bénéfique pour la rentabilité d?un gîte en augmentant sa teneur en minerais (Marshall et al., 2000). Jusqu?à présent, dans les terrains métamorphiques, les contextes sédimentaires et plutoniques ont été reconnus et respectivement explorés pour les gîtes de type SEDEX et les gîtes magmatiques de Ni-Cu. L?étude de gîtes de métaux de base et précieux intensément métamorphisés (faciès des granulites) et leur comparaison avec des gîtes équivalents peu on non métamorphisés a permis d?établir, au cours des dernières décennies, des outils pour l?exploration des terrains de haut-grade métamorphique (Vokes, 1991, 2000; Slack et al., 1993; Spry et al., 2000). Ces outils sont basés sur la reconnaissance de roches diagnostiques d?une circulation ou d?une exhalation de fluides hydrothermaux telles que les méta-exhalites (formation de fer, coticules, tourmalinites, roches riches en quartz-gahnite, en apatite, en barite ou en staurolite zincifère) (Spry, 2000; Spry et al., 2000). Ils sont utilisés constamment dans les ceintures supracrustales riches en roches métasédimentaires.

May 1, 2003

By Richard Burt

"In seeking to supply the ever increasing needs for raw materials, the mining industry has been required to develop lower grade resources in increasingly remote regions of the world. This has resulted in the extension of many frontiers, both technologically and geographically.The accent of mineral processing research over the last few decades has been to “do existing things better”. There have been many breakthroughs in equipment and processes; however in general the accent has been to increase capacity of existing unit processes, often by orders of magnitude, or to refine the process itself by basic research and development. This has lead to added sophistication, enabling the process engineer to maintain optimum performance of his equipment while reducing the cost, and the amount of labour needed to operate the plant.While much of the increased requirement for resources is handled by the development of ever larger, lower grade orebodies, a significant portion still comes from the small miner - even the artisanal miner - operating in remote and often politically sensitive parts of the world. For them, innovation and simplicity are the keys, not sophistication.The tension between sophistication and simplicity - or research and reality - is specially evident in the area of gravity concentration of rare metals, such as tin and tantalum. This paper looks at this tension, primarily from the eyes of an operator and seeks to put into perspective the two paradigms."

Jan 1, 1999

By Jeff R. Reinson

The Diavik Diamond Mine is producing diamonds from two orebodies, the A154 South and A154 North kimberlite pipes, discovered beneath the waters of Lac de Gras. Innovative dike technology with appropriate water collection and treatment systems allowed Diavik to start open pit mining of the ore bodies in 2002. To allow planning, engineering, and implementation of sufficient water handling infrastructure, reasonably accurate estimates of groundwater inflow quality and quantity over the life of mine are required. Prior to mining, a numerical model using the continuum approach was developed for regional and site wide water management. After approximately two years of mining, groundwater inflows to the pit were found to exceed those predicted by the base case hydrogeologic model. The most likely explanation was flow through Dewey?s Fault zone. As this fault was not explicitly accounted for in the model, a detailed hydrogeologic investigation was conducted to evaluate its geometry and hydraulic properties. A multi-disciplined approach was used and involved core logging, fluid logging, geophysical logging, packer testing, a pumping test, and water quality sample collection. The results of the field investigation were used to update the conceptual and numerical models and to develop a Discrete Fracture Network (DFN) model to address small scale problems such as flow into future underground drifts. The updated numerical hydrogeologic models predict that up to 70 per cent of the groundwater inflow to the A154 N/S open pit is through the relatively narrow fractured rock zone associated with Dewey?s Fault. Consistent with the continuum model, the DFN model predicts that inflow to a drift excavated in Dewey?s Fault will be approximately 10 times the inflow to a drift excavated in competent rock. The DFN model provides a better understanding of the distribution of these inflows on a local scale over the length of the drift.

May 1, 2006

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units."

Jan 1, 2012

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

By L. C. Bird, N. T. L. Landgren, M. W. Mikhail

"Through funds made available in 1972 by the Nova Scotia Department of Mines and Energy (DME) and the federal Department of Regional Economic Expansion, a program was initiated to recover saleable coal from mine waste dumps adjacent to the existing Acadia wash plant in Stellarton, Nova Scotia.Following evaluation of these dumps in 1972, the Acadia wash plant was modified to treat high-ash material. The first production was recorded in late 1974. By the end of 1979, a total of 738,202 t of dump material had been processed, yielding a total of 205,212 t of thermal-quality coal.The successful Stellarton operation led to considering the possibility of recovering thermal coal from other dumps. Evaluation of the Westville dumps indicated total recoverable reserves of 1,346,617 t averaging 53.8OJo ash.Parameters for plant design were defined from the washability characteristics of the dump material and the results of a bulk test. Two options were proposed; one was to use the existing plant with some modifications, the other was to build a modular mobile plant that could be used at future dump sites in the province after Westville. At the 25% ash level, the potential recovery of coal from the dump was estimated at 41% yield (by weight) or 549,679 t."

Jan 1, 1981

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017

By D. J. W. Piper, T. Hundert, G. Pe-Piper

"Abstract - Potentially commercial deposits of kaolin are found in the fluvial Lower Cretaceous Chaswood Formation, the sedimentologically proximal equivalent of deltaic sediments of the offshore Scotian basin. The geological setting of the kaolin deposits has been interpreted from high-resolution seismic-reflection profiles and boreholes, and mineralogical studies on one reference borehole. The kaolin is a product of early diagenesis involving meteoric water below the water table. The distribution of kaolin is controlled by the presence of intraformational unconformities that were sites of ground water recharge, and are marked by the development of oxisols above the water table. Such diagenesis was facilitated by interbedded, loosely consolidated, permeable sandstone. The highest-grade kaolin deposits are found in areas close to river belts, where overbank muds were not sufficiently drained to develop paleosols, but where later uplift created intraformational unconformities. In the sandstone, meteoric water flow altered feldspars to kaolin, thus yielding commercial silica sand deposits. It also altered ilmenite to rutile, which is concentrated as secondary placers in modern rivers that have eroded the Chaswood Formation and tills derived therefrom. Sommaire - Des dépôts de kaolin potentiellement économiques ont été notés dans la Formation de Chaswood d&apos;’âge Crétacé Inférieur, laquelle constitue un équivalent latéral en milieu fluviatile aux sédiments deltaïques du bassin de Scotian. Le contexte géologique de ces dépôts de kaolin a été interprété a partir de profils de seismique-réflection à haute résolution, de sondages, et d’études minéralogiques sur un sondage de référence. Ce kaolin est un produit diagénétique précoce formé par de l’eau météorique sous le niveau de la nappe phréatique. La distribution du kaolin est contrôlée par la présence de zones de recharge associées à des discordances intraformationelles marquées par le développement d’oxisols au-dessus du niveau de la nappe phréatique. La présence d’interlits de grès perméables faiblement consolidés a contribué à l’efficacité de ce processus diagénétique. Les dépôts de kaolin les plus riches se trouvent en périphérie des rivières, là ou les boues de la plaine d’inondation n’étaient pas suffisamment bien drainées pour permettre le développement de paléosols, mais où des mouvements verticaux subséquents ont crée des discordances intraformationelles. La circulation d’eau météorique dans les grès a entraîné l’altération des feldspaths en kaolin, générant ainsi des dépôts économiques de sable de silice. Elle a aussi causé l’altération de l’ilménite en rutile, que l’on trouve dans des placers secondaires situés dans des rivières contemporaines qui ont érodé la Formation de Chaswood et les tills qui en sont dérivés."

Jan 1, 2006