Search Documents

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By P. V. Golde, R. A. Poole, G. R. Baiden

"The results being presented in this paper are those obtained during 1996 on a drilling automation project at Stobie mine. This project has successfully demonstrated that the remote operation of multiple drills (by a single driller) from surface using Tamrock Data Solo 1000 Sixty drillrigs is technically feasible and can potentially bring significant rewards in terms of productivity and work environment improvements, as well as labour and maintenance savings. BackgroundThe ObjectiveThis paper is an update of a previous report on remote drilling research at Stobie mine. Enabled by the communications system installed at the mine, the ability to remotely control underground equipment from surface has been demonstrated (Poole et al., 1996). This paper discusses the needs and process required to carry this concept to consolidate the operation of multiple machines under a single operator.The TeamThe team assembled to develop and implement the automation and the communi-cations extensions needed to allow the multiple machines’ operation from the surface by one operator included the following:INCO Mines Research supplied the project management and original project initiative. The primary purpose was to prove the advantages of savings associated with the driller not being required to travel to the underground drill location coupled with the savings associated with one-man, multiple-machine techniques.Tamrock EJC supplied the Data Solo 1000 Sixty drills and the Tamrock specific machine-based custom software. The drills were produced in Finland with no provision for remote operation of the drill from other than the umbilical attached local console.Automated Mining Systems supplied the modifications to the drill communications equipment to allow the machine communications to become broadband compatible. As well, Automated Mining Systems also supplied the hardware necessary to be able to remotely control the portable video camera, as well as the data logging equipment.Stobie Mine personnel were made available to test the function and then integrate the concept of remote control drilling into the Stobie operations."

Jan 1, 1997

By A. Ghirian

Once cemented paste backfill (CPB) is transferred and placed into a mine stope, various coupled mechanisms will take place in the CPB material or structure. It will be subjected to strong coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes. Field studies have shown that the in-situ properties and performance of CPB differ from those obtained in the laboratory. This is mainly due to effects of the aforementioned coupled THMC mechanisms or processes. For a reliable and cost-effective design of a CPB structure and barricade, it is crucial to have a proper understanding of the THMC behaviour and evolution of CPB. Also, it is important to consider the effect of coupled THMC factors (e.g., self-weight pressure, drained/undrained and thermal conditions, pore pressure) while curing the CPB specimens. For this purpose, a laboratory setup is developed to investigate the properties of CPB materials. The setup is capable of curing CPB specimens (10 cm in diameter and 20 cm in height) under controlled vertical pressure (curing under stress) and various coupled THMC conditions, while continuously monitoring the evolution of total stress, pore pressure, suction, temperature, water drainage, chemical composition of the pore water and vertical deformation. Once the required curing time is achieved, the specimen can be extracted and then subjected to experimental tests of interest, such as those that determine the Unconfined Compressive Strength (UCS), shear strength parameters, saturated hydraulic conductivity and thermal properties. In this paper, we describe the developed experimental setup and present some results of the THMC behaviour of CPB under various curing stresses and rates of backfilling. The obtained results show that the THMC properties of CPB are strongly coupled due to several mechanisms, such as self-weight pressure, heat of hydration and suction development as a result of self-desiccation. The findings can assist researchers and practitioners to better understand THMC behaviour and thus design more cost-effective CPB structures.

Aug 1, 2013

"11.1. IntroductionThe recovery of platinum-group elements (POE) from ores is a subject which has received almost no mention in the literature. Edwards (1975) refers to the process used for refining of the POE, throughout the Western World, as a so-called ""conventional"" process .... ""not because of the simplicity or convenience of the operations, but more probably because of the inertia of established processes and the aura of secrecy with which the major platinum refiners have surrounded this process."" There is no doubt in this writer's mind that the latter is also applicable to the dearth of knowledge of the mineralogy, geochemistry and ore deposits of PGE and that the poor recoveries, mainly attributed to the mineral beneficiation stages of concentration, are also affected by this traditional secrecy. Fortunately, this attitude is changing, due no doubt to the advantages that accrue from more open research which may be critically assessed in the literature in the traditional manner. Examples of this more open approach to recoveries and recovery problems are represented by Newman (1973), who gave some typical recovery percentages for Merensky Reef ores, and the recent encouragement and cooperation on mill samples from the Sudbury area by lnco Metals Company (cf. Cabri, 1981a).In general, platinum-group elements are recovered from an ore by the use of a physical concentration method, such as gravity separation or flotation, followed by further upgrading using further physical, wet chemical or pyrometallurgical techniques. The final process of refining in which the individual platinum-group elements are produced in pure form is outside the scope of this chapter.Platinum-group element deposits naturally fall into different categories according to the recovery process best suited for them, viz. those amenable to gravity separation, those amenable to flotation, and those where platinum-group elements are by-products of base metal sulphide, chromite and miscellaneous other deposits."

Jan 1, 1979

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By J. Chretien

The ability to continuously monitor the air quality within a mine has become instrumental in becoming a low cost producer. The many considerations involved in monitoring air quality include sensor type, hardware placement, as well as data storage medium. BESTECH has had the opportunity to gain insight into these air quality monitoring considerations through deployments of NRG1-ECOTM, a minewide energy consumption optimization system. This paper explores the particular challenges overcome through these installations, and provides a set of guidelines for mines that want to maximize data capture while minimizing costs. It provides a view of additional benefits of air quality monitoring, such as ventilation control, reporting and trending.

Aug 1, 2013

By F. H. Hueston, R. S. Barclay

"Depending on the application, zirconia, fused magnesia and graphite have been found to be the most suitable crucible materials for melting uranium metal and its alloys. Although graphite has been found to be satisfactory for uranium and uranium alloy castings with cross sections of 4 square inches or greater, ceramic-type molds are superior for small sections and those shaped castings which prohibit the economic use of machined graphite molds. Heating cycles, addition mechanisms and furnace conditions for melting are discussed."

Jan 1, 1967

By P. W. A Severin

"The Sturgeon Lake deposit, a partly eroded lens of massive sulphides with an underlying sulphide stringer zone, is one of five orebodies that occur in the Sturgeon Lake area of northwestern Ontario within volcaniclastic rocks of the Archean Wabigoon Subprovince in the Superior Province of the Canadian Shield.The Sturgeon Lake Cu-Zn-Pb-A g-Au deposit was discovered in October 1970 as a result of an I.P. survey. Production from this open-pit mine began in March 1974 and continued until the ore was exhausted in March 1980.The Sturgeon Lake property is underlain by basaltic volcanics, minor amounts of mafic lapilli tuff and rhyolite volcaniclastics. A quartz crystal-bearing rhyolite occurs at the top of the felsic volcaniclastics and is ""capped"" by the Sturgeon Lake massive sulphide deposit. The felsic volcanics have been intruded by a crudely layered sill-like, carbonatized mafic intrusion. Recent work suggests that the felsic rocks that underlie the Sturgeon Lake deposit are lateral equivalents of those in the vicinity of the Mattabi Mine and are not correlative with the dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits. Hydrothermal processes that resulted in the formation of the Sturgeon Lake orebody have resulted in a depletion of Na2O, CaO and FeO and an increase in MgO, K2O, copper and zinc. In the vicinity of the sulphide stringer zone, the rhyolites are ""bleached"" due to silicification and sericitization. The rocks lying immediately below the massive sulphides are locally strongly chloritic.The Sturgeon Lake deposit may have formed on a top ographic high which prevented mafic flows and dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits from inundating the Sturgeon Lake fumarolic vent from the west. Continued or resurgent activity from the Sturgeon Lake fumarole may have resulted in the formation of the Lyon Lake and Creek Zones as more ""distal "" deposits in topographic lows. The Sturgeon Lake, Lyon Lake and Creek Zone deposits were subsequently overlain by mafic tuffs and flows."

Jan 1, 1982

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By John E. Callahan

"A stream sediment geochemical survey covering an area of 13.000 sq. km near Churchill Falls. Labrador. was conducted for Brinex (British Newfoundland Explorations Ltd.) prior to partial flooding by the Churchill Falls power project. Stream sediments (minus 80-mesh) were analyzed for Cu, Pb, Zn, Ni, Ag, Mo. U and Mn, and the heavy mineral, nonmagnetic fraction (minus 60-mesh) for Cu, Pb, Zn, Ni, Ag, Mo, Ba and Mn. A binocular examination of the concentrates for sulphides and pyrope garnet was done on the heavy mineral concentrates. The concentrates were also examined for fluorescent minerals.Two distinct areas with high trace-element values indicate the need for follow-up studies. The first is in an area of gabbro erratics containing massive and disseminated sulphides (pyrrhotite, pyrite and minor chalcopyrite) on the western edge of the survey area along the Esker Road. The second, largest area (several hundred square kilometres) is anomalous in U and Mo and associated with felsic intrusives (Red Wine Complex?), syenites. granite gneiss and sedimentary rocks (Seal Lake Group?).The binocular study showed that almost 15% of the heavy mineral concentrates contained pyrite and no other sulphides. This indicates that this technique may be worthwhile in determining the presence of sulphide minerals in stream sediments from glaciated environments. The only fluorescent mineral observed in the study was zircon."

Jan 1, 1981

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By K. R. Nichol

The author points out that corrosion works 24 hours a day, every day. It is an economic reality that the cost of corrosion is inevitable and that its cost should be incurred in the least expensive way. An economic evaluation technique to properly assess its relative impact is the Discounted Cash Flow Method. Various remedial and corrosion control measures are available and these, when coupled with a planned corrosion control program, help reduce the cost of corrosion.

Jan 1, 1973

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By Mory Ghomshei

Pebble Creek Geothermal Power project is associated with a massive recent volcanic eruption in Southwestern British Columbia Canada. Slim holes drilled to depths 1100 m in the prospect area, show very high temperature gradients around 80?100?C/km. The temperature and chemistry of the Pebble Creek hot springs indicate the possibility of a steam reservoir in the prospect area. In addition to high temperature gradients, presence of host rocks with high permeability, along with abundance of recharge waters (from the Lillooet River) provides clear signature of a high-grade geothermal power reservoir at depth 2000 to 3000 m. Data show that over five hundred Megawatt of green power can be generated from the prospect area in a commercially viable manner. The generated power will be base-load, which in comparison with large hydro has the advantage of lower capital costs and a significantly smaller footprint. The final hurdle to overcome, before starting the development phase, is deep exploratory drilling for resource confirmation. This paper is a summary of the data available on the Pebble Creek geothermal power prospect, presented in the context of viability of the resource for large-scale commercial power generation.

Aug 1, 2013

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By A. F. Sirianni

The Peace River iron ore deposit represents the sole source of raw material for an integrated steel industry in Alberta. The ore has proved refractory to beneficiation by a number of techniques. A selective oil-phase agglomeration technique is described. Medium-grade concentrates, analyzing 48-53% Fe and 10-14% SiO2 were obtained with recoveries of about 75% of the total iron. These results appear to represent the optimum possible for this ore body.

Jan 1, 1977

By C. R. Edwards

"Since the first commercial extraction of uranium in the early 1940s, the range of feasible process alternatives has greatly increased. This paper reviews process options to reduce extraction costs, improve efficiencies, effect safer operations, and lessen environmental impacts. Equipment and processes used in the past, in use now, and that could be considered for future use are described.BackgroundTwo billion years ago life on earth consisted solely of single celled creatures of the simplest design (Gould 1989). Incredible as it may seem, uranium fission reactors were operating then also. In what is now western Africa, a series of natural reactors were fueled by rich uranium deposits in contact with underground rivers. Water from the rivers provided the moderator necessary to sustain the nuclear fission chain reaction. These primordial reactors ran down after about 600 000 years (Ontario Hydro 1989).Because it is ubiquitous in the earth's crust, humans have always been in contact with uranium. Mining of uranium, albeit not intentional, is ancient ; uranium minerals were embedded in ore veins mined for metals such as silver and copper.Uranium was discovered in 1789 in Berlin by an apothecary, Martin Heinrich Klaproth, who named the element after the recently discovered planet Uranus. The metallic element uranium, as opposed to its compounds, was extracted in 1841 by the French chemist Eugene-Melchior Peligot. The atomic mass of uranium was calculated to be 120, but the Russian genius Dmitri Ivanovich Mendeleev (famous and welcome everywhere except in Russia, where his liberal politics were detested by the Tsar), found this did not fit into his periodic table, and submitted a value of 240. Mendeleev was close; the exact atomic mass is 238.029.Henri Becquerel's detection of the radioactivity of uranium in 1896excited scientific study of the metal, but virtually no practical use was found for uranium outside of a minimal consumption as a colouring agent for glass and ceramics. Scientific interest intensified in the 19305. In 1933 Leo Szilard patented the concept of the nuclear chain reaction. While walking to work on a fine fall London morning and mulling over the problem of how to release atomic energy, he was stopped by a red light. He stood in thought and conceived the notion of the neutron-activated chain reaction before the light turned green. The patent was filed in 1934, and Szilard assigned it to the British Admiralty in order to keep it secret, in an honourable but ultimately futile effort to prevent the misuse of science (Bronowski 1973)."

Jan 1, 1992