Search Documents

By Lloyd W. Trevoy

Syncrude Canada Limited is presently studying commercial production of heavy minerals from plant tailings of the openpit A lhabasca tar sands operation. When tar sands are processed and upgraded to synthetic crude oil, heavy minerals can be removed f rom the extraction circuit and beneficiated to provide concentrates of zircon and titanium minerals. Calculated recovery rates indicate that crude oil production capabilities of 105,000 barrels per day would provide 26,000 tonnes of zircon and 114,000 tonnes of titanium minerals annually. The titanium minerals concentrate is a mixture of ilmenite, leucoxene and rutile; it could be used as recovered or upgraded to synthetic rutile. With the consrruction of further synthetic crude oil plants in Western Canada, a large reserve of heavy minerals will become available.

Jan 1, 1984

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001

By Karl J. C. Harries

13.1. RIGHT TO RECEIVE ROYALTY CONTRACTUAL ONLY1

Jan 1, 2003

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By S. Kivrak

The firms in construction industry could not sufficiently adapt the rapidly emerging information technologies in recent years into their corporate structures. Therefore, in an effort to further exploit the benefits of information technology (IT), integration of the experiences and backgrounds of construction industry and the advantages of IT, is one of the most open-ended fields for improvement in this industry. Utilization of IT in the construction sites will positively affect the efficiency, productivity, quality and health & safety issues in the construction sites thus the cost and completion time of the projects. Within this context, augmented reality technology, which brings a new perspective into IT, can be put into the service of construction industry. Augmented reality which has been designed to improve the services in many application domains such as school education, military warfare, military trainings, industrial maintenance, retail and medical, can be defined in the simplest form as augmenting the real world with information from the virtual world. The main aim of this study, which presents an overview of an ongoing project, is to develop an innovative method by making a construction worker, foreman, equipment operator or a site engineer watch a very comprehensive and informative animation which will enable the said staff to perform or supervise all the phases of the activity he or she is in charge for in a more efficient, productive, safer and qualified manner by means of smart glasses using augmented reality systems. In this respect, training material related with the activities in the construction sites will be prepared and with a well-fictionalized scenario, animations exhibiting all the phases and details regarding the related activity (e.g. masonry, formwork and rebar works etc.), method of statement, correct and incorrect applications in comparison-wise manner, will be produced. Therefore, the user will be able to reach the training material, method statements etc. in the animations about the activity he or she is in charge for, enabling him or her to figure out the work as prescribed in the specifications. Basic trainings about the system will be given to target group, i.e. construction workers, foremen, operators, site engineers and managers working in the construction sites to apply the system on sites after all the system was tested. After the testings, to determine the effectiveness of this system, semi-structured interviews and survey questionnaires will be conducted among the mentioned target group. Therefore, the potential benefits of this system to the construction industry can be determined. The main target of this study is to implement an efficient, thorough construction management by orienting the staff in the construction sites to perform efficient, safe and qualified works by means of smart glasses that use augmented reality. There are relatively few studies about the implementations of augmented reality technology in construction. The outputs to be attained in the end of the study have the potential of improvement of time, cost, quality and safety parameters by ensuring a qualified, safe, efficient and productive construction management via augmented reality technology in the construction industry.

Aug 1, 2013

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

Aur Resources is Canada's leading copper mining company with producing mines and development projects in North, Central and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca and Andacollo Mines in Chile was a record 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Novicourt Inc (45%) and Teck-Cominco (25%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6% Cu, 1.5% Zn, 26 gr./m.t. Ag and 0.9 gr./m.t. Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

"The outlook for Eastern Canada is decreased coal production and for Western Canada increased production. The market for Western coal is expected to reach 40 million tons per year in metallurgical and thermal-power markets.Technical developments in Eastern Canada include successful methane drainage experiments, modifications to the shearer-loader to improve cutting rates, mechanized mining of a tail-gate stable and mechanical stowage of level brushing. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Underground hydraulic experiments were started in 1969. The importance of reclamation was recognized and plans have been made to re-vegetate disturbed areas and mine dumps.The Mining Research Centre closed the field office in Nova Scotia and is preparing to open a new field office in Calgary, Alberta."

Jan 1, 1970

By C. J. Edmonds, R. Bland, W. C. Ferguson, R. Whitehead

"In 1969, the Environmental Science Division of James F. MacLaren Limited received authorization from The International Nickel Company of Canada, Limited to carry out a water quality monitoring program in the Lake Shebandowan region of Ontario, where a new base metal mining and milling complex was expected to go into operation in 1972. The objective of the program is to establish base-line water quality characteristics. Fully realizing their corporate responsibility to minimize the effects of the proposed activities on the environment, Inco decided that it would be desirable to establish a program by which any change in the quality of environmental waters will be detected before detrimental conditions ensue, permitting prompt corrective measures to be taken. The program has been in progress for over two years. The waters are sampled and analyzed four to six times per year. Sampling stations are located in Lake Shebandowan and on the adjacent Gold Creek - Matawin River system. On-site analyses and measurements are made of flow, dissolved oxygen, temperature and pH. Samples also are collected for later analysis in the laboratory. These samples are analyzed for a wide range of chemical and biological characteristics. The paper discusses the extent of the sampling program, the techniques utilized and the value of such programs in maintaining the quality of the environment."

Jan 1, 1973

By R. Siwik, N. K. Davé

"The national reactive tailings (RATS) program is a co-operative industry-government effort to develop practical techniques for closure of reactive tailings areas. This paper summarizes the RATS program objectives and areas of research, and details the Noranda/CANMET project on the Waite Amulet tailings.Geophysical and biohydrogeochemical investigations were carried out at an inactive copper-zinc mine tailings site, Waite Amulet, in Noranda, Quebec. Geophysical investigations consisted of seismic, electromagnetic conductivity and electrical resistivity surveys to determine the thickness of the layers above bedrock and to map conductivity variations within the tailings and the immediate outlying area. Biohydrogeochemical investigations consisted of installing multilevel piezometer nests to determine groundwater flow patterns and porewater chemistry, obtaining solid core samples and characterizing for physical, chemical and mineralogical parameters, and iron oxidizing and sulphate reducing bacterial counts.The geophysical survey indicated a bedrock ridge extending under the tailings from the northeastern outcrop which may act as a porewater boundary layer. The survey also indicated a 2 to 20 m clay layer underlying the main tailings dam. Preliminary results of the saturated zone porewater chemistry have indicated three major zones of high electrical conductivity varying between 1,000 to 12,000 µs and pH between 3.4 to 8. Lower pH and high metal and sulphate concentrations were obtained in a shallow zone near the water table. With depth, the concentration of metal and sulphate ions decreased and pH increased below the water table. The underlying clay layer is relatively impervious -and most of the seepage from the tailings is probably exiting from the sides of the impoundment dam."

Jan 1, 1987

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By C. Overton, R. W. Nice

"With todays economic trials and tribulations we have all become deeply engaged in costs and cost cutting in our field of mineral processing. Grinding is one of the most expensive unit operations. The cost of grinding media is the most expensive item in grinding costs. Therefore, it is only reasonable to attack the cost-cutting area by trying to reduce the consumption of media. This introduces the field of autogenous or rock-on-rock grinding.Rock-on-rock grinding is not new to us. It has been known for many decades;The South Africans used pebble grinding in the '20's for gold.Mr. B. Crocker was prompted for the same reasons to introduce pebble grinding at Lakeshore Mines in Kirkland Lake during the last war.The Buffalo Anchorite used beach pebbles in grinding prior to the war.Autogenous and semi-autogenous grinding is used quite successfully in the iron ore field. Base metals have their examples in Australia at Caba, in Africa at Komato and in Sweden at Aitik.Recently three mills in British Columbia and one in Arizona started with autogenous mills in their circuits. One was originally conceived to utilize a modified autogenous grind with a crusher in the circuit. All except the same mill had contingency plans for converting to semi-autogenous. All four mills have since converted to the semi-autogenous mode. These are Island Copper, Lornex, and Similkameen in B.C. and Pima Mining in Arizona."

Jan 1, 1975

By V. Panayotov, M. Panayotova, R. Villas-Bôas

The "United Nations Framework Classification (UNFC-2009) for Fossil Energy and Mineral Resources 2009” is the international system designed to meet (to the extent possible) the needs and to support the decision making and resources management of private industry investment, governments, policymakers, bank investment, scientists. There are different international and national systems classifying commodities (resources, reserves, possibility and feasibility to extract them, etc.) with their own definitions and reporting terminology which often do not overlap entirely or even differ significantly - thus creating difficulties and problems among stakeholders to understand each other. The UNFC-2009 is developed to allow “speaking in one language”. The paper presents briefly the UNFC-2009. The UNFC-2009 applies simultaneously three fundamental criteria to classify projects: economic and social viability, field project status and feasibility, and geological knowledge (so called E, F and G axes), thus creating a visualized, easily understandable three dimensional system. The E, F and G axis categories are divided to subcategories, using additional criteria. The UNFC-2009 is already applicable to solid minerals, nuclear fuel resources, petroleum. The amounts of solid waste generated by metals production from ores (mining, minerals beneficiation, extraction metallurgy) and its metals content are discussed from the viewpoint of using the waste as resource. An attempt is made to apply the UNFC-2009 to technogenic waste from metals production from ores - both to old engineering constructions (historic mining dumps and reclaimed beneficiation tailings ponds) and new (currently in use) dumps and ponds.

Jan 1, 2016