Search Documents

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

By Lye GN

Rock mechanics investigations have shown that some major slopes in the Panguna pit would be stable at angles in excess of 500 providing near-surface instability could be controlled. Excavation of final batters at angles between 55¦ and 60¦ is now being carried out using D10 dozers with berms at 45 to 60 m centres. A trial slope with berms at 90 m centres is planned. Shotcreting of weak zones combined with crest reinforcement, with rock anchors and dowels, is used to provide protection against erosion and toppling of the crests. Overall slopes excavated in this way are of the order of 10¦ steeper than slopes obtained by blast and shovel excavation.

Jan 1, 1986

By Barnett LJ

The Kellogg slag fuming model is extended to apply to the Port Pirie plant which uses recuperative heating of secondary air. Exten- sive investigations of plant operations pro- vide parameters for use with the model, and verification that the resulting model provides simulation which is very close to actual plant performance. The model is used to_deter- mine optimum slag fuming operating conditions, and the results of several other investigations with the model are briefly described.

Jan 1, 1975

By P Knights, M S. Kizil

Truck/shovel operations constitute 50 - 60 per cent of the cost of open pit mining operations. Mining companies, therefore, are constantly seeking to close the gap between actual truck/shovel productive capacity and maximum potential truck/shovel capacity. This paper analyses the performance of a mixed truck/shovel fleet in an open cut coal mine in Australia. It analyses operating delays, and proposes a novel graphical means of determining truck-limited or shovel-limited operations. A goal seeking algorithm is advanced in order to maximise truck/shovel match factors (MF) and hence optimise fleet productivity.

Sep 26, 2011

Taiwan is situated between Ryukyu and the Philippines with 35,960 sq. km of area, being slightly larger than Belgium It has roughly a spindle-shaped outline with a longitudinal axis extending in a roughly north-south direction. Geologically, Taiwan is extremely complex in terms of its tectonic setting in the convergence zone between the Asian continent and the Philippine Sea Plate. To the east of Taiwan, the Philippine Sea Plate subducts beneath the Ryukyu island arc, and to the south of Taiwan the Philippine Sea Plate overrides the Asian plate along the Manila Trench. Taiwan, therefore, occupies an unstable region between these two well-defined subduction systems of opposite polarity (see the following block diagram).

Jan 1, 1987

By Kabel J. G

While a per onnel location system is primarily used to check that nobody is left in the mine at firing time, it is also useful for contacting people, uch a foremen, shiftbosses and tradesmen, who travel over several mine levels during a shift. The system installed at The Zinc Corporation, Limited, Broken Hill, uses punched coded plastic identity tags, with "In" and "Out" tag readers on each level. When entering a level, the employee inserts his tag in the "In" reader, and when leaving, in the "Out" reader. Each reader is connected to a central computer which shows who is still in the mine and their location.The system has been used on 3 levels by 21 men for a trial period of 4 months. It ha proved reliable in an underground mining environment, and employee acceptance has been good.

Jan 1, 1984

By Tsuchida N

The history of world nickel production has been affected significantly by the supply and demand situation and fluctuation of LME price of nickel metal. In the beginning of the 1980s, the decline of price and demand lead to the withdrawal of un-competitive producers and the shrinkage of the production capacity. During the same period, Sumitomo Metal Mining maintained the production level with continuous improvement of the traditional matte electrorefining process. However, Sumitomo has recognised that the continuous improvement alone does not promise us the ability to catch up with rapid changes in the world. In the meantime, Sumitomo intensively researched chloride hydrometallurgy and has developed the chloride process for the nickel refining. This includes the solvent extraction and chloride electrowinning in the mixed sulphide process and the chlorine leach of the anode slime arising from matte electrorefining. In the late-1980s, Sumitomo Metal Mining decided to develop a new nickel refining technology based on chloride hydrometallurgy. The new process was designed from the comprehensive aspects involving safety and the environment. Construction of the plant for the matte chlorine leach electrowinning (MCLE) process was commenced in 1991. The MCLE plant with a capacity to 2000 tonnes per month has been commissioned at Niihama since 1992. The process has provided high productivity, overall good economics and high quality of electrolytic nickel produced. After the establishment of the process, Sumitomo has maintained continuous improvement of the new process and has attained the best practice of the work classification.

Jan 1, 1996

By Komosa T

The increase in the proportion of sulphide ore treated by the gold mining industry has led to generally higher oxygen requirements. Additions of pure oxygen, hydrogen peroxide and in some cases calcium peroxide, have been proposed as a means of satisfying the oxygen demand and overcoming the problems from reactive sulphides in the ore. Current oxidant addition options and practice are reviewed.Laboratory oxygen demand tests are reported for a suite of ores to show some of the effects of pH and preaeration.Laboratory leach tests at high and low dissolved oxygen levels are reported on two of the ores with higher oxygen demands, and the results are assessed in terms of gold leaching kinetics, ultimate gold extraction, and cyanide requirements.

Jan 1, 1992

By F Pothitos, S Hewson

The geological and geotechnical conditions at the Cadia Hill Open Pit are very complex. This complexity coupled with high mining rates has required significant technical input into the design and optimisations of the pit slopes, accesses, cutbacks and scheduling. A multi-discipline team of NML engineers, geologists and external consultants has been conducting comprehensive geological and geotechnical programs in order to achieve an optimum design of the pit slopes. Extensive data collection, analysis and interpretation has led to the formation of working geotechnical models of large structures, rock masses, and back-analysed slope performance charts. The current Cadia Pit Optimisation Project focuses on the risk-and-return principle for pit design and on the integration of geotechnical, hydrogeological, mining engineering and scheduling. The risk management for pit design has also been incorporated into the short term and long-term operation of the pit mining to ensure safety and production.

Jan 1, 2003

By T Cutts

Since 1989 Kalgoorlie Consolidated Gold Mines has managed the Kalgoorlie gold operations of joint venture partners Normandy Mining Ltd and Homestake Gold of Australia Ltd. Current production from the Fimiston Open Pit is approximately 650 000 ounces per annum. The mine incorporates a multitude of narrow shear hosted, subvertical lodes, predominantly within Golden Mile Dolerite. Traditionally KCGM has used blasthole based grade control in the Fimiston pits. A single sample is taken from vertical production blastholes, drilled on ten metre benches. This process was improved with the addition of infill drilling along blasthole rows to provide additional samples across strike. However the limitations of adequately defining subvertical mineralised structures with vertical blastholes remain. In 1997 the first of two trial areas were drilled with close spaced, inclined Reverse Circulation (RC) drilling. These tests indicated that RC based grade control had the potential to provide significant advantages. These include:improved delineation of mineralised structures, particularly across strike; reliable short-term mine schedules based on the advance data available from drilling over three benches; and the angled RC drilling is capable of providing samples of near stope and stope fill material which often remains unsampled by blasthole drills due to the safety constraints around unstable underground openings. Based on the success of this initial work RC based grade control was gradually implemented across production areas commencing September 1998. Some of the many challenges faced include:development of effective procedures and systems for the planning, logging, interpretation and modelling of the RC data; obtaining adequate drill coverage due to mine scheduling constraints and restricted access around underground openings; requirement for integrated systems to handle either blast hole or RC data; and development of effective methods to evaluate the performance of RC grade control. RC based grade control is delivering significantly improved lode definition, grade estimation and subsequent ore classification.

Jan 1, 2000

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrrhotite/arsenopyrite concentrate, in order to describe the mineralogy, composition and surface area of the calcines. Sulphides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second; pyrite predominantly roasted via a pyrrhotite intermediate. Sulphur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, while having the greatest surface area, were the most refractory with respect to gold solubilisation, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-microscopic gold in the second stage.

Jan 1, 1992

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

By M J. Nugus, S C. Dominy

Mesothermal lode-gold deposits often pose problems during sampling because of their complex and erratic gold grade distribution, and the presence of coarse gold. Effective sampling and sample preparation protocols must form the basis of any resource estimate at whatever stage a project is at. Design of a sampling regime must be based upon a thorough understanding of orebody mineralogy and geology. This should include consideration of gold particle size and distribution. The sample type, size and density employed must also be based on the underlying geology of the deposit. Choice of sample preparation procedure and assay type is of critical importance if fundamental sampling error and analytical errors are to be minimised. Traditional fire assays, using small charge sizes, consistently understate assays gained from large charge sizes and techniques such as screen fire assay and bulk leach extractable gold assay. The proportion of coarse gold within samples will have a profound effect on the requirements for sample preparation and assay method. The application of Gy sampling theory can help to reduce errors within the processing of samples of broken rock. Quality control/assurance of sampling regimes must also be critically assessed. The problems associated with sampling mesothermal lode-gold type deposits are presented as case studies from Western Australia and North America.

Jan 1, 2003

By Thomson S, Eisenstein Z

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

Kidston Gold Mines Limited (70 per cent Placer Pacific and 30 per cent Public Shareholders) has been mining the Wises Hill Pit since late-1984. The Wises Hill Deposit is a large low grade gold deposit and as such is highly sensitive to economic parameters. The uniformity of the orebody has allowed a bulk mining method to be used, with minimal dilution. Total reserves defined to-date are 64 160 OOOT at a grade of 1.60 g/t gold. Mineable reserves remaining as of January 1992 are 36 357 OOOT at a grade of 1.28 g/t gold.Mining investigations to reduce the impact of lower gold prices, the effect of decreasing headgrade and increasing mining costs have focused on wall steepening.

Jan 1, 1992

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

By Paine G. G

The measurement of the fragmentation size distribution of a blast muckpile can be achieved directly by screening the entire muckpile. Screening of muckpiles in a production operation is generally not practical due to the logistics and time involved moving large volumes of rock through a screening plant. An indirect technique to assess blast fragmentation size distributions has been developed. This technique uses photographs of the blast muckpile taken at intervals during the excavation cycle. The images from the photographs are input to desktop computer software via a digitiser tablet. The software compilates the rock fragment sizes and calculates a size distribution. This paper discusses the technique and subsequent data analysis. Examples of the application of this technique for the assessment of comparative blast performance are given.

Jan 1, 1990

By Matsuhisa Y, Sakurai W, Shimazaki H, Peiming H, Fukahori Y

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skam Pb-Zn deposits in the Kamioka mining district, central Japan, where the wall rocks consist of heterogeneous rock units. The results (8180sMow of -1.1 to +17.3%o and 613CPDB of -5.0 to +4.8%o for limestones, and 8180SMOW of -0.8 to +12.5%c for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (180 and 13C) toward the center of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralization. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to- rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralization had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360m.

Jan 1, 1995