Search Documents

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

By Moort van J C

A new low-intensity magnetic separator which operates by spinning particles in a continuously rotating magnetic field is able to reduce particle entrapment of non-magnetics to an almost insignificant level. In such separators the removal of ma

Jan 1, 1997

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992

The financing of mineral ventures is usually supported by the valuation of a mineral asset, the physical size and composition of which have been determined within quantified limits of accuracy in order that the lending or investment risk can be assessed. The Resource or Ore Reserve estimation is the measurement of that asset and may be the outcome of complicated processes of interpretation and estimation requiring an extensive knowledge and understanding of the general nature of ore occurrences, and of the particular deposit under review. In arriving at an interpretation of the nature and physical distribution of minerals in a deposit, observations may only be available from widely spaced samples and geological knowledge and principles are of prime importance. Consultants may be asked by the lending or investing body to "provide comfort" on the quality of the Resource or Reserve estimations and providing such comfort casts substantial obligations of diligence on the consultant.

Jan 1, 1990

By Dierling D. H

The paper briefly describes the mining system employed on Western Deep Levels for the past 20 years. The negative aspects which gave rise to a new mechanized method of mining are discussed. The sequence of events leading from the Mine's first attempt at trackless mining in 1980 to the present day in-stope project is presented. The original justification for this project and the in-stope trackless mining method is described in detail. The results to date are evaluated and the original rationale for going in-stope trackless mining questioned. A totally new mining philosophy for Western Deep Levels, whereby major geological disturbances are left in situ and longwalls re-established and mined using trackless mining machinery is described. The economics of this mining method are discussed. Trackless mining machinery can also be put to good use within the conventional longwalls in a new method of mining using Load Haul Dumpers (LHD) in reef drives. When the instope trackless mining project commenced in 1983, it was stated that expansion to any significant degree with diesel powered vehicles could be ruled out and electrically driven alternatives would have to be developed. This issue is discussed and the Mine's decision to expand with diesel powered vehicles explained. Finally, the extent to which trackless mining is likely to be seen in the 1990 s at Western Deep Levels is discussed.

Jan 1, 1986

By Propser M, Szekely J

Flow maldistribution in the iron blast furnace has been studied analytically by the use of the vectorial form of the Ergun equation and experimentally via packed columns and a cold model of a blast furnace. Experimental results are presented showing the effect on fluid flow patterns of the following types of nonuniformities in a packed bed: the increased voidage at the wall ("wall effect"), the decreased voidage at the interface between layers of materials with different sizes and shapes, and the differences in resistance to flow of bulk regions of a column with different sizes and shapes. The proposed theory is applied to the calculation of fluid flow patterns for these nonuniformities. Velocity profiles, as calculated from these flow patterns, were found to agree reasonably well with experimental measurements obtained via hot wire anemometry techniques for laboratory scale packed columns. Calculated fluid flow patterns are presented for blast furnace burdens which show how flow patterns are affected by (a) coke segregation and (b) the relative differences in resistance to flow between coke and oxide pellet layers. For the cold model study, calculated flow patterns are presented based on photographs of a given burden distribution. The velocity profiles calculated from these flow patterns were found to agree reasonably well with the velocity profiles measured from the cold Model.

Jan 1, 1975

Utah Development Company operates a mine at Blackwater with a present annual production of 4 000 000 tonnes of coking coal. Mineable seams outcropping on the company's lease are part of the Permian Mammoth Rangal Coal Measures. Current operations are based pre- dominantly on the Main Lower seam. Coal quality variations occur along the seam strike, in the direction of seam dip, within the seam plies and in isolated anomalous areas. Raw coal of non-specification quality is washed to reduce ash and sulphur and to improve the free swelling index. Raw coal meeting specification quality is sent directly to product, by-passing the washplant. Careful attention to mining, coal preparation and product blending is necessary to ensure that the combined product meets specifications.

Jan 1, 1974

1991 New Zealand Branch Annual Conference û Appendix

Jan 1, 1991

By Skinner J, Brackenbury K

The AuPlus" Systems have been applied in the gold mining industry to achieve improved gold recoveries, faster leach kinetics and reduced cyanide consumptions. Calcium or hydrogen peroxide, collectively known as peroxygens, can be used. The choice depending on plant design and the nature of the ore. Laboratory test work and plant trials are included in this paper to illustrate the benefits of peroxygen usage in extractive gold metal- lurgy.

Jan 1, 1991

By B, R E. Browner, H R. Watling

A number of hydrometallurgical treatment methods are being developed to extract copper from chalcopyrite flotation concentrate including microbial leaching and ferric sulfate leaching. However, chalcopyrite is difficult to process efficiently by hydrometallurgical methods as it exhibits slow reaction kinetics. Comparative leaching tests do not always satisfactorily explain or predict observed copper recovery, acid consumption, or differential leaching of minerals. This is especially true when reactive gangue constituents are present. The aim of this study was to determine how the leaching regime (microbial versus ferric sulfate) affects both the extraction of copper and residue mineralogy. Chalcopyrite flotation concentrate was leached at 30¦C and 65¦C using a pure culture of Acidithiobacillus ferrooxidans and a mixed consortium of thermophiles, respectively. In addition, the concentrate was leached at the same temperatures using 0.1 M ferric sulfate. Microbial leaching of chalcopyrite extracted more copper than ferric sulfate oxidation of chalcopyrite at 30¦C, demonstrating that the microbes promoted the solubilisation of copper at this temperature. This result was confirmed by leach solution analyses and residue analysis using quantitative X-ray diffraction (QXRD). More chalcopyrite was oxidized with ferric sulfate at 65¦C than at 30¦C (as expected). QXRD confirmed that pyrite reacted during ferric sulfate leaching at 65¦C but was relatively unreactive during lower temperature leaching. The high ferric ion concentration in the ferric sulfate leach at 65¦C led to significant precipitation of jarosite. This phase was only detected in small amounts at 30¦C in both the microbial and ferric leached residues. Sulfur also precipitated in the ferric leaching at 65¦C whereas no sulfur was detected in the microbial leached residue. Quartz was a relatively unreactive mineral phase regardless of the leaching medium and temperature. QXRD analysis indicated the residue mineralogy differed with different leaching regime.

Jan 1, 2004

The South Mine, property of Broken Hill South Limited, is situated at Broken Hill, NSW, Australia, towards the southern end of the main lode. The leases (MLs 7 and 8) cover a length of 2400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1940 feet below the collar of the original main shaft and to 825 feet below sea level. Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30 000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet. A typical assay for a monthly period is 14.4 per cent Ph, 5.6 ozs Ag, and 11.6 per cent Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and zinc concentrates produced are railed to other centres for the extraction of the contained metals.

Jan 1, 1994

The advantages of coordinate geometry in design and construction of underground works are apparent for reasons of flexibility, security, computer operations, survey error analysis, and the use of numerical techniques for setting out and checking works. Integration with National or State survey systems is useful in the long term, both at design, construction and future works stage. Equipment and methods are available which permit "absolute" monitoring of structures and strata over long periods,to close toler- ances. This work can be carried out in the limiting urban environment. Rapid data acquisition by semi-automatic devices, or photogrammetry, utilizing electronic data processing is capital inten- sive, but provides more data than analogue surveys (i.e., setting out centre lines) and becomes more attractive with increased labour Costs.

Jan 1, 1976

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By Lo YC, Pate WT

In recent years there has been a great deal of interest in ways to optimise the performance of mineral processing plants. This paper describes a methodology developed for optimisation of autogenous and semiautogenous mills. The methodology involves plant sampling, batch testing, modelling, computer simulation, control strategy evaluation and implementation. The models have been tested in plant operations to verify the research findings and predictions. Two example applications of this approach to plant optimisation are presented. Benefits reported in these two examples are in the range of four - eight per cent increase in size reduction efficiency.

Jan 1, 1993

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

By Watkins JR

Movements in the mineral trade cycle are almost invariably out of phase with the gradua- tion rate of mining engineers, metallurgists and geologists. This commonly leads to situations where graduates are scarce in "boom" periods and in free supply when the trade cycle is depressed. This problem reflects the difference in elasticity and flexibility between the educational and industrial environments. In the educational system the decision that brings students to graduation is made three to five years prior to the event. This is quite a lengthy period of time in terms of mineral trade cycles. By contrast, the mineral industry has far more elasticity in responding to short term fluctuations in mineral trade. The authors do not believe that the mis- match between the availability of skilled personnel and the manpower requirements of industry in the short term is intractable. Much is to be gained by more realistic and rational manpower forecasting combined with greater flexibility in the educational realm.

Jan 1, 1982

By Baguley PJ, Napier-Munn TJ

This paper presents preliminary resu]ts from field studies which were conducted to establish, among other things. the influence of medium viscosity on the partitioning behaviour of dense medium cyclones and drums in mineral applications, using frrrosilicon- ba_sed media. The medium vicoosit.y- was measured on-line, and partitioning behaviour was determined using ore sampling and density t r acers . The results demonstrate that viscosity is an important. operating variable, influencing ,eparat.ing density and efficiency under certain conditions. The implication is that metallurgical performance can be optimised by manipulating viscosity, either by appropriate selection of medium' characteristics or by automatic alarming and/or "ontroi using signals from the on- 1. i ne viscometer.

Jan 1, 1987

Consideration is given to the factors affecting raceway activity and the hearth design of a zinc-lead blast furnace. Results of measurements made on operating furnaces are given and comparisons are made with published data both from operating iron blast furnaces and from dynamic models of the zinc-lead blast furnace. Indication is given of the methods used for assembly of the relevant information into the specification of a commercial furnace design. A discussion on the comparative merits of furnaces of circular and essentially rectangular plan is given based on the concepts explained in the paper.

Jan 1, 1981

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976