Search Documents

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006

By D B. Donato

Gold mining cyanide-bearing solutions can pose a risk, cause significant wildlife deaths and adverse public relations and result in non-compliance with regulatory conditions. The International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code) was developed as a voluntary code to encourage industry-wide improvements in managing cyanide responsibly. The Code requires design and implementation of robust monitoring programs for compliance under the following standards of practice: 4.1, 4.4 and 4.9. A robust monitoring regime can be complicated as each processing and tailing system is different. The following systems are commonly used in Australia: carbon-in-leach (CIL); carbon-in-pulp (CIP); heap leach process ponds; tailing waste disposal systems; peripheral discharge, central discharge and in-pit disposal. Some terrestrial wildlife can be denied access by fencing tailing storage facilities (TSFs) or other physical barriers, therefore limiting wildlife interaction with cyanide-bearing tailing and solutions to mainly birds and bats. While wildlife monitoring programs for processing and TSFs contain similar core attributes, it is necessary to adapt monitoring to take into account the site-specific features of each system. These core attributes are discussed in this paper, with reference made to cyanide concentration and associated methodologies. The issue is considerably complicated if tailing solutions are deemed or discovered to be toxic to wildlife. Essentially cyanides are required to be measured to gain an understanding of the concentrations to which wildlife may be exposed. This usually equates to measuring the cyanide concentration of solutions entering and leaving a tailing system. To assess the risk to wildlife presented by tailing and heap leach systems it is necessary to monitor both the hazard (cyanide concentrations) and the exposure (live wildlife species, presence and interaction). These tasks need not be arduous and a system of simple frequent monitoring has been developed and implemented for Code compliance. The wildlife monitoring developed by Donato Environmental Services (DES) and used at mining operations departs from the industry norm. It documents observer effort, live wildlife presence, habitat and behaviour in a tailing system, as well as deaths and carcasses. A greater understanding of wildlife cyanide toxicosis associated with this monitoring approach will enable mining companies to adopt a proactive approach to significantly reduce, or preferably eliminate, the impact on wildlife and assist in gaining Code compliance.

Jan 1, 2007

By P Stoker

The need for quality assurance and quality control (QA/QC) in the sampling and assaying of minerals is fundamental to the reliability and confidence of a mineral resource estimate, reserve estimate and possibly profitability of a mine. In spite of this, QA/QC practices in the mining industry are commonly applied poorly, or misunderstood. As New Leaders, we should aim to correct the poor practices and become fully informed on appropriate procedures. This paper uses worked examples that show the usefulness and importance of best practice QA/QC procedures. Fundamentals of reviewing the performance of the laboratory by examining the results of client inserted standard reference material (standards), blank material and duplicate samples are discussed. To do this, three examples from Australian data sets have been used. For each example, simple and efficient plotting techniques are suggested with subsequent evaluations of each plot. The first case study compares the results of internal standards from a laboratory with blind standards (where the expected value is unknown to the laboratory) submitted by the client. It was demonstrated over time that the laboratory was unintentionally analysing the internal standards in a different manner to the remainder of the sample batch. In this example, not understanding the cause of a high negative laboratory bias could have led to poor understanding of the depositÆs grade and in the extreme a proposed mining operation may have reached operational stage with a subeconomic grade. The second case study discusses the quality of blank material submitted by a mining operation to monitor cross-contamination within the laboratory. The blank material contained background levels of the element under investigation. This created uncertainty in the assay results, which could have led to the need for additional assays and drilling programs. Finally, the third case study demonstrates the use of the relative paired differences (RPD) technique to cross-validate the results from duplicates and repeat analyses from two laboratories. The three examples given show either laboratory or operational error. If left undetected, each example could have had serious implications for the mineral resource estimate and ultimately, the mining operation. These examples are not isolated occurrences; poor QA/QC practices are an industry wide problem exacerbated by rapid staff turnover and increased contractor positions on-site. New Leaders must be equipped with a thorough grounding in QA/QC best practices to improve its application and confidence in the results of sample analysis.

Jan 1, 2009

In recent years, the. art of electric steelmaking has received a great deal of attention, and naturally, much controversy has existed from time to time regarding the relative merits of different practices and tywes of furnaces. Nevertheless, at the present time, the basic principles of the process are reasonably well established, and by far the greatest percentage of electric steel is a product of the basic lined, direct arc type furnace. Ferro alloy manufacture has demanded the development of furnaces having very different characteristics to those used for steel. Some special alloys, however, require conditions of manufacture which are more closely approached in the steel type furnace, and thus the latter has been adapted where necessary for the production of these alloys.One such alloy, low carbon ferro-manganese, is manufactured at Whyalla, South Australia, in a basic-lined, direct arc furnace, which is used alternatively for the production of alloy steels.BRIEF HISTORY OF THE ELECTRIC FURNACEThe principle of melting by electricity was first applied to the melting of iron in 1879 by William von Siemens, whose equipment consisted of a small crucible into which were introduced two carbon electrodes. Very little practical development took place in the next 20 years, although in 1890 a Frenchman named Heroult designed a direct arc furnace for the production of ferro alloys. At the beginning of the 20th century, several types of furnaces were patented for steel melting, the most important of these being the Heroult, using a direct arc, the...

Jan 1, 1951

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

MANPOWER RESOURCES The optimisation of human effort has been an ongoing and significant process in the coal industry since industrialisation as we know it began. The extent to which the changes sought have been achieved has, over the years, been in the main determined by the economic and political forces existing at that time and the determination and character of the individuals involved. The question of optimisation is therefore not new in our industry. Hopefully this presentation will demonstrate to the reader the effect of previous measures adopted by industry to optimise all facets of its operation and in particular that of the human Resource.

Jan 1, 1991

A mathematical model for spontaneous combustion of coal with moisture included is presented in this paper. The one-dimensional unsteady state model consists of conservation equations for oxygen, water vapour and inherent moisture of coal and energy for both gaseous and solid phases. A first order Arrhenius reaction rate for oxidation under both pore diffusion and chemically controlled reaction regime is considered. The rate of evaporation or condensation is also considered as a function of temperature of coal, water content of coal and gas streams. The equation of the model is solved numerically by the finite difference technique. Influences of different parameters on the process of spontaneous combustion can be examined by using this model. Also the model can be used to simulate full-scale storage conditions.

Jan 1, 2005

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By P Hatherly, A Melkumyan, D Wyman

Chemical species distributions in rock sequences can be modelled using Gaussian processes (GPs) to predict the weight percentage between known data points. This method can be improved by dividing the modelled area into regions of different mineralogy. In the context of many iron ore deposits, marker shales give the initial guidance of where these regions may lie. These shales give rise to distinctive peaks in the natural gamma downhole logs, which are conventionally identified by hand. A GP method has been developed to automate this task.Once the appropriate boundary has been located on the basis of shale occurrences, chemical assays from exploration drill holes are used to find the exact boundaries of interest. These boundaries divide the drill hole stratigraphy into regions of different mineralogy, each of which display their own distinct correlations between the main elements and oxides (Fe, SiO2 and Al2O3). Iron ore shows a negative correlation between Fe and Al2O3, but in banded iron formation (BIF) there is a positive correlation between these species. Similarly, SiO2 and Al2O3 have a positive correlation in the shales and ore but a negative correlation in the BIF. Correlations obtained within ore-, BIF- and shale-dominated regions are therefore better than those obtained using the entire log and can be used to improve the results obtained when modelling.

Sep 26, 2011

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

By V A. Diemar

The Chatree Gold Project represents a greenfields discovery of metallurgically clean shallow gold mineralisation in a logistically simple terrain. Total Measured, Indicated and Inferred Resources are currently 31 tonnes of gold and 160 tonnes of silver. Gold occurs in an adularia-sericite epithermal system within quartz-calcite-adularia veins, breccias and stockworks. Host rocks are volcanic arc porphyritic latite-trachyte flows, their pyroclastic equivalents and volcaniclastics of upper Permian to upper Triassic age. The mineralisation was deposited in dilated zones during repeated reactivation of pre-existing structures. To-date five mineralised prospects have been defined by drilling with three reaching JORC Code Mineral Resources status. The project is in its definitive feasibility stage and is anticipated to be in construction during 2000.

Jan 1, 1999

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The Henty Gold Mine is a good example of a situation where conditional simulation and optimisation techniques may have useful impact on modelling of mineralisation distribution and ore definition. Much of the gold mineralisation at Henty is concentrated within an alteration zone which is both physically discontinuous and forms only a small fraction of the overall mineralised volume. The alteration units are mappable from diamond drill core and underground workings. Conditional simulation and optimisation techniques for ore definition have found considerable success in the open pit gold mining environment. For many reasons including computational efficiency, lack of consistent geological information, and lack of familiarity with ideas and methods among mine geologists, implementations of these methods in open pit mining have been comparatively simplistic. Modelling is commonly reduced to treating the sample data as a single geologic population. This paper discusses the application of the MP method (a particular implementation of conditional simulation and optimisation) to modelling the distribution of potential ore blocks in the Henty gold mineralisation. The approach allows the mine geologist to model both the spatial geometry of the alteration types and the gold grades associated with each alteration type in a single process. Options allow the geologist to include or exclude underground geological mapping and face sampling depending mainly on the abundance of drill hole sampling and the quality of the face sampling. An optimisation algorithm based on maximisation of profit from mining is used to assist in ore definition.

Jan 1, 2000

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The use of concentrated solar flux for high temperature metallurgical applications is a wellresearched area with several reported literatures on solar calcination and metal oxide reduction. This paper presents two such processes with potential to reduce the carbon footprint from ironmaking through using concentrated solar flux. The first process involves solar flux incorporation to the recently developed lime-magnetite pellet (LMP) route of magnetite ore agglomeration. The second process is a hybrid solar-smelting route for iron ore-coal composite pellets that utilises solar flux to provide process heat. Both the concepts of solar agglomeration and solar smelting process were investigated using a solar simulator-hybrid reactor set-up at Swinburne University of Technology. Results from solar agglomeration experiments at 950°C suggested no change in the reaction mechanism of the LMPs under solar irradiation compared to electrical heating. The percentage and morphology of the primary phases (mainly CaFe3O5) appeared similar for both solar and electric heated LMPs. The solar-smelting of magnetite concentrate-lignite coal composite pellets at 1130°C showed a maximum metallisation of 55 per cent after 1.5 hrs of reaction. The solar-smelt process has about 25 to 35 per cent lower CO2 emission compared to the blast furnace ironmaking. Technoeconomic analysis of implementing a CST facility in an existing composite pellet process suggested a payback period of about ten years at a heliostat cost of $A100/m2 and natural gas cost of A$10/GJ. The economics of CST implementation can be further enhanced by decreasing the thermal losses from the heliostat field and reactor.

Nov 8, 2021