Search Documents

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By F Schoenbrunn, T Laros

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to be successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings impoundment design, underflow pumping, and control system.

Jan 1, 1998

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80 000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100 m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By J Player, P Evans, G Sweby

Achieving quick underground access after the completion of an open pit mine can be critical to maintaining project value and ensuring regular ore feed to the mill. This paper outlines the design and construction for two portals in an active open pit to commence underground development quickly whilst installing appropriate ground control to maintain long term access in an uncertain setting. Implementation of the portal designs was complicated by the change in underground design from hangingwall access to footwall access late in the life of the open pit due to preferable ground conditions. The portal locations did not have easy access for ground support installation integrated into the pit design due to the timing of the underground design changes. Practical implementation of the ground support systems subsequently became a key part of the project. Intact rock strength, rock mass characteristics, gradational weathering / alteration profile and structural information were modelled against pit displacement monitoring as the basis from which the portals were located and ground support schemes designed. Conditions around one of the portals necessitated numerical modelling to estimate the appropriate level of ground control for long term stability. The design was completed whilst the open pit was actively on-going and the portal areas not entirely exposed. The rock mass assessment and analysis for the two portals indicated different ground support scheme capacities would be required. The expected level of control for one of the portals also necessitated the use of monitoring with extensometers and load cells to ensure the rock mass response and ground support scheme performed as planned. Construction of the portals demonstrates the benefit of a considered design process, a plan which allows practical installation of ground support schemes where access is limited, the benefit of ongoing monitoring to ensure performance remains within design limits and the challenges involved working within an active pit with limited floor space.

Mar 15, 2021

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By A Densten, C Gimber

Surface water management and drainage is a key aspect of mine rehabilitation and closure planning. In the authors’ experience, drainage related problems are amongst the most common forms of failure in mined landscapes. The appropriate design of surface water infrastructure is therefore a key focus of practitioners. While there is currently a trend towards distributed drainage networks and avoiding hard engineered structures, in many situations (especially for existing landforms) engineered drainage structures cannot be avoided. CITATION:Gimber, C and Densten, A, 2018. A risk-based approach to drainage design standard selection for mine rehabilitation and relinquishment, in Proceedings Life-of-Mine 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

By A Muhairini, M Eggers, J Smith, H Baxter

Detailed geochemical analysis of cored and non-cored drill hole data was used to characterise and model the Cenozoic detrital valleys of several deposits within the southern Pilbara region, Western Australia. The purpose of this modelling was to better characterise and understand the relationships between the various geotechnical units comprising mixtures of rock and soil for the purposes of slope stability and depressurisation studies.This paper presents data from several valleys where geological, geomorphological and climatic processes have resulted in the deposition of heterogeneous detrital rock and soil sequences. Seven primary detrital units are recognised as occurring within all the valleys studied, suggesting that the geological processes involved in the erosion and deposition of the units were widespread. Geochemical assessment of cored and non-cored data suggests correlatable geochemical signatures can be recognised for each of the units; however, local variability in the groundwater history of individual valleys is demonstrated by late-stage carbonate precipitation recognised both in the core and through the geochemical signatures, which has resulted in alteration of the parent rock/soil material. This paper discusses how the carbonate alteration may lead to improvements in rock/soil mass strength of a clay unit by comparing laboratory strength test samples of the same parent material with varying degrees of precipitate alteration to those with no discernible carbonate alteration. Following from this, correlations with geochemical assay results have been derived, whereby zones of more favourable strength conditions may be modelled through assessing areas of analogous geochemistry.The paper demonstrates how geochemical assessment can lead to improved geotechnical and hydrological modelling for a detrital valley system without the need for significant coring and laboratory testing. This in turn leads to improved confidence in the slope design and depressurisation recommendations for a slope.CITATION:Baxter, H, Eggers, M, Muhairini, A and Smith, J, 2015. The effect of carbonate alteration on detrital mass strength and implications for geotechnical slope design, in Proceedings Iron Ore 2015, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By J Heyes

Historically mining engineers haven't spent enough time planning waste dumps, but waste movement costs often outweigh ore haulage costs. There is a real incentive to plan waste dumps right the first time to minimise rehandle and final closure costs. At BHP Billiton Iron Ore there has been an increasing sophistication in waste dump design and they are becoming as important as the pit design. Closure landforms are now included in mining studies. Closure is embedded in the business planning cycle. The results from the recent life of mine study at Whaleback is a case in point where a base case of the shortest hauls with no closure constraints was compared against a closure case. A properly planned and executed waste plan revealed that no rehandle was required and haulage costs were eight per cent less if closure design implementation was carried out concurrent with mining. At cessation of mining the landforms were such that decommissioning of critical acid rock drainage dams and coverage of exposed pyrite areas could occur straight away, without the need for additional rehandle.  The paper also covers design and scheduling elements of waste design both in-pit and ex-pit, management of potentially acid forming material (PAF) and trends in PAF management and designing for final landform closure. This paper illustrates that there is value in terms of costs savings, sustainable outcomes and reputation if the mine planners are involved in the closure planning process.

Jan 1, 2009

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

By P J. Handley

"Predicting how coal seams will be beneficiated through the coal handling processing plant (CHPP) has long been challenging within BHP Coal. Various coal seams from different areas are mined and stockpiled separately, often depending upon a deleterious coal quality parameter; high/low trace elements for example. These stockpiles are then fed in different ratios into the CHPP to produce the desired product/s. In understanding the washability characteristics of the feed source, mine geologists and process engineers work together to improve the beneficiation of different coal materials through the CHPP.For the majority of the BHP Coal deposits, the washability data is available for the coal seams across the deposits. However, no previous standardised modelling and prediction technique existed that could ensure the correct information was available for forecasting and refining CHPP processes. This paper will discuss the steps undertaken to implement a geometallurgical prediction tool that simplified and streamlined the washability modelling and yield estimation process. The value realised to the BHP Coal assets resulting from this process was: improved compliance to plan increased throughput increased CHPP recovery through improved efficiencies and increased revenues.CITATION:Handley, P J, 2017. Washability modelling and estimation techniques used to improve coal handling preparation plant beneficiation, in Proceedings Tenth International Mining Geology Conference 2017, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By J A. Meadows, M G. Annandale, G Castelain

Bauxite mining on Cape York Peninsula (CYP) commenced in the early 1960s in the region surrounding the town of Weipa. Rio Tinto Alcan (RTA) operates its bauxite mines on the homelands of 11 Indigenous Traditional Owner groups. The mining activity currently operates under three Aboriginal Agreements including an Indigenous Land Use Agreement – the Western Cape Communities Coexistence Agreement (WCCCA) – which provides RTA with access to the land in return for a range of benefits to the Traditional Owners, including employment, training, royalty payments and future relinquishment of the land (Klimenko and Evans, 2009). Despite reports of some ‘good progress’ in meeting the terms of the WCCCA (Klimenko and Evans, 2009, p 5), many of the region’s Traditional Owners remain dissatisfied. Two key areas of Indigenous community concern are the current premining management practices and the outcomes of post-mining landscape rehabilitation efforts.CITATION:Annandale, M G, Castelain, G and Meadows, J A, 2016. Sustainable mining – indigenous community benefit, in Proceedings Life-of-Mine 2016 Conference, pp 173–175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Vakili

Dilution is associated with considerable direct and indirect costs in underground open stoping operations. As shown in previous works, an improved ability to predict dilution enables the economic risks associated with unplanned dilution to be reduced. Depending on the width of the orebody and depth of mining, the economic performance of an open stoping operation can become even more sensitive to dilution. It is shown in several well-documented studies that as little as 1 per cent of additional dilution can impose millions of dollars of lost profits per annum. Optimisation of a stoping operation is therefore largely dependent on the ability of the operation to minimise dilution. This can only be achieved through sensible analysis of past and future performance of mined stopes using the most appropriate recent available technologies and tools. This article presents a new design process that utilises advanced geotechnical numerical modelling and various other analytical tools to assist with a more robust mine design of open stoping operations. The focus of this design process is on geotechnical factors affecting dilution during the life-of-mine. A recent application of this optimisation method for a mining operation is presented in this paper as a case study. Through the application of this method and various other operational improvements, the mine was able to deliver more consistent production and lower operating costs over its life-ofmine outlook and was able to reduce dilution by up to 50 per cent and achieve sustainable record high production rates.

Mar 29, 2023

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By S Warden, T Neville, P Leckie

At its simplest, the classification and characterisation of an orebody is a matter of Where, What and When. Where and with what spatial resolution are measurements taken, What properties are measured, and When are the data acquired, processed, and delivered to create the most value. This paper delves into how existing and near-term advances in measurement technologies, field automation, and whole-system-digitisation are combining to open new routes for mine and exploration productivity improvement. Commencing when the initial exploration hole is dug, the advancement in deployment of survey technology—from expert-operated, to driller-operated, to driller-integrated—is used to demonstrate a template for adoption of higher technology measurements. We then introduce and discuss the multi-use measurement as offering outsized returns from a single measurement run, highlighting two new technologies that acquire rock strength while drilling and downhole assay data as examples. For rock strength, we highlight a novel approach to determining Uniaxial Compressive Strength (UCS) while drilling, its relationship to and advantages over Mechanical Specific Energy (MSE), and how it offers utility to multiple downstream processes. For downhole assay, we detail how a back-tophysics approach to Pulsed Fast and Thermal Neutron Activation (PFTNA) analysis offers significant advantages over other measurement methods and earlier implementations of PFTNA, generating a rich data set that can significantly extend and improve the information on which mining decisions are made. Finally, we discuss the possibilities enabled via optimising data delivery, collection, and curation— noting a fundamental limitation of historical systems and exploring the possibilities that will be unlocked by soon-to-market solutions that better enable Orebody Characterisation data to (virtually) move in space and time with rock material post-blasting. Ultimately, the value of optimising the Where, What, and When from point of measurement to the moment it generates maximum value will create greater life-of-asset production for a lower cost and energy input.

Sep 1, 2024