Search Documents

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By Gray L. L., Max Littlefield, Godbold A. C.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By Max Littlefield, Godbold A. C., Gray L. L.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By Gerard Matthes

ONLY in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be con-templating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist&apos;s chief complaint in life is a dual one-inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground-geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the :geologist or mining engineer an aerial photograph or mosaic is only a tool, the effecient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most, skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted.

Jan 1, 1928

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world&apos;s produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world&apos;s demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world&apos;s barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By P. L. Weston, S. E. Khalafalla

A systematic study was made by the Bureau of Mines on the effect of so me hypothesized accelerators for the process of wustite reduction in carbon monoxide. When small concentrations of promoter materials in the order of 0.69 at. pct were added to the reducible charge, the rate of reduction to iron was increased. Promotion phenomenon prediction was made in light of a suyface reduction mechanism with the aid of Vol&apos;kenshtein&apos;s effect regarding the propagation of crystal lattice disturbances by small amounts of relatively larger interstitial ions. The acceleration produced by a typical promotor, such as potassiunl, increases with protnoter concentration up to a maximum, beyond which the reduction rate decreases. Concentration for maximum promotion depends on the nature and physicochemical properties of the promoter. The extent of reduction rate enhancement is found to be directly proportional to the atomic volume and electronic charge of the additive. DESPITE the enormous volume of literature on iron oxide reduction, very little is reported concerning additive or impurity effects on this important metallurgical process. The beneficial effect bf calcium compound additions on the reducibility of iron oxide sinters has been reported by Tigerschiold,1 vor dem Esche,2 and Edstrom. Doi and Kasai~ found that the addition of lime or limestone to iron ores helps to break up any unreducible compounds, such as fayalite or ilmen-ite. and thus free the combined iron for reduction. Schenck et al. 5 suggested that the increased reduction rate obtained when adding lime could be accounted for by the instability of wustite in the presence of lime. Acid-base slagging reactions resulted in wustite disproportionation according to The dicalcium ferrite formed will yield iron and calcium oxide during reduction. Regenerated calcium oxide dissociates more wustite. This mechanism has been used by Seths and white7 to explain their experimental results. Recently, Strangway and ROSS&apos; attributed the calcium carbonate acceleration of iron oxide agglomerate reduction to increased porosity, both initial as well as that developed during reduction. Aside from calcium carbonate, or oxide, no other promoter was noted in the literature, except for a brief mention by Barrett and woodg on the effect of sodium carbonate and aluminate as activators for the hydrogen reduction of magnetite at 600°C. The present investigation systematically studied a host of other promoters, including calcium and sodium, in an attempt to elucidate the mechanism by which promotion takes place and to fit the results into a simple chemical model. To attain this goal, the effect of promoter physical properties, such as atomic volume, electronic charge, and concentration are related to wustite reduction kinetics in this paper. Wustite reduction to iron, rather than the overall hematite reduction, was chosen since this reaction is known to be the slowest, and hence the rate-deter mining step for the overall iron oxide reduction process. EXPERIMENTAL PROCEDURE Raw Materials and Their Preparation. The pure or impregnated wustite pellets were prepared from minus 400-mesh chemically pure hematite powders. A known weight of hematite was thoroughly and uniformly mixed with a calculated weight of the additive. The mixed paste containing 35 wt pct water was gradually heated from 400" to 1200° C and fired at 1200°C for approximately 4 hr in an air atmosphere. After cooling, the sinter was pulverized to minus 100 mesh and pelletized into minus 4- plus 5-mesh spheres. Pellets were fired, similarly to the paste mix, air-cooled, sized, and stored. An appropriate weight of the charge (20 g) was placed in a zirconia reduction tube maintaining a uniform oxide bed height of 1 cm and a cross section of 7.1 sq cm for all of the test runs. The samples were supported in the vertical reaction tube by a bed of fragmented insulating firebrick plus 3- to 6-mesh alumina beads. The hematite was then transformed to wustite by reduction with a 30 pct CO2-70 pct CO gas mixture at 1000°C in a globar furnace. Complete conversion to wustite was ascertained by a continuous infrared gas analyzer recording the CO-CO2 content of the effluent gas until no carbon monoxide was absorbed from the inlet gas, and inlet-outlet gas analysis remained constant for 30 min. The wustite sample was then reduced with 100 pct CO at 100WC. From the recorded data, an initial rate of reduction was determined by the initial slope of the graph percent reduction vs time. In order to estimate the accuracy of the data, five separate determinations of the reduction curve of pure wustite, under otherwise identical conditions, were performed. The maximum deviation from the average reduction at 14 min amounted to 2 2 pct reduction. This deviation corresponds to 3.8 pct variation based on the percent reduction of the sample. Aiiy impurity effect below the limits of this maximum deviation was considered a spurious result. If the effect exceeded + 4 pct, then it was considered as a positive one. Considerable care was exercised in determining the initial rate from the slope of the initial segments of the curve. Each reduction curve was examined separately on large graph paper and the best tangent to the curve at zero time was drawn. The slope of this tangent was taken as a measure of the initial fractional reduction per minute. Although the time required to reach 50 pct reduction may be of special practical significance, initial rate measurements are invaluable in fundamental studies. These rates provide a measure of the process kinetics on the initial

Jan 1, 1968

By D. W. Fuerstenau, D. A. Sullevan

In the experimental work for this comparison of wet and dry grinding, it was found that the size distributions for wet grinding operations are characterized by a constant value of the distribution modulus, (a; whereas, for dry grinding the distribution modulus decreases slightly with increased size reduction. Wet grindability seems independent of the weight of material in the mill while dry grindability depends on weight. Experimental data and eqmtions for each process are presented for noncleavable isotropic material, for cleavable or material in which there is some form of internal stress, and for energy consumption. The equation ED/EW=BK-? (where ED and Ew are, respectively, energy for wet and dry grinding, k is the size modulus, and B and ? are constants) was found to give the ratio of energy. Dry grinding is generally considered to require more energy than wet grinding. Taggart&apos; states that power consumption in wet grinding ranges from 60 to 90 pct of that required for dry grinding. Bond&apos; states that dry grinding requires one third more power than wet grinding. It is interesting that Rose and Sullivan&apos; note this same difference in power required for wet and dry grinding, but they state that on purely mechanical grounds it is difficult to see any great difference in fundamental principles between wet and dry milling, since dry milling may be regarded as wet milling with a fluid of low viscosity (i.e., air vs water). Yet it must be the viscosity of the fluid that is responsible for the differences between wet and dry grinding. Probably the most comprehensive investigation comparing wet and dry grinding has been that made by Coghill and Devaney. They compared the grind-ability of both chert and dolomite in a 19x36-in. batch ball mill under both wet and dry conditions. In these tests the weight of ore in the mill was varied from 35 to 200 lb and each grinding test was carried out for such period of time that the amount of -200-mesh material in the product was essentially the same for each test with a given material. Cog-hill and DeVaney&apos;s data for the grindability of dolomite, which are reproduced in Fig. 1, show that a comparison between wet and dry grinding is com- plex. The comminution of a material by a wet grinding method is characterized by a constant grindability over a wide range of mill loadings. Since grindability is the weight of material comminuted per unit of energy expended, it is equivalent to (w)/ (p)(t), where W is the weight of material being ground, P is the power, and t is the grinding time. In the case of wet grinding, the grindability of dolomite in the Coghill and DeVaney experiments was 0.546 * 0.009 ton per hp-hr when the load of dolomite in the mill ranged from 50 to 200 lb. On the other hand, for dry grinding no such simple relationship was found to exist between power, time, and weight of material in the mill. Dry grinding efficiency appears to depend greatly upon the amount of material within the mill. When the mill contained

Jan 1, 1961

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By T. A. Rickard

An educated man is distinguished neither by his clothes nor by his knowledge; he is replarkable not for the things he says, but for the way he says them. You cannot even stand with him under an archway in the rain without finding him out. He may talk only of the weather. His words and his phrases alike may be simple. -at distinguishes him is the arrange- ment of his words; however desultory his talk, it will be method- ical; he has habituated himself to foreseeing the part to be played by each word he uses and the place to be taken by each sentence he utters. On the other hand, the uneducated man, though shrewd and well-informed, will relate facts and events as they recur to him, generally in disorder; in his effort to recollect and in his attempt to rectify forgetfulness he will pause irregularly, filling the intervals with meaningless phrases, such as "and then ", "and: so ", or &apos;said he to me", "said I to him"; and even the contipuous parts of his story will be told confusedly-because he has not learned the proper use of words.* My own experience as an editor of technical manuscripts has taught me that the misuse of &apos;that&apos; and &apos;which&apos; is a fruitful cause of obscurity and confusion. The relative pronouns have distinct functions, and no writer can express himself clearly until he has learned to discriminate between these I functions. For example:

Jan 1, 1931

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

By C. C. Harris

This article presents a general equation describing the xYt surface in batch grinding. This equation contains as special cases most of the relationships which have been deduced from kinetic studies. In an earlier paper an analytical solution of the integro-differential equation of batch grinding was proposed1 as a first approximation of the xYt surface.&apos; A more general equation will be presented here, which appears to combine in a single statement many conclusions reached by experiment. A possible underlying mechanism is that the changing product fineness leads to changes in the particle crushing strength and in the probability of encounter with the crushing media.

Jan 1, 1969

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer&apos;s recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free&apos; from folding and faulting.

Jan 1, 1935

By Henry Fernald

THE accounting system or bookkeeping methods of any company are principally the concern of that company and of those who are in control of its affairs. Its published financial report is, however, primarily intended for those who are not already fully informed regarding its operations and finances. Whatever may be the advantages of standardization of accounting and bookkeeping methods, it must be admitted that a company has a certain right to handle its accounts and keep its books and records in whatever manner may seem to it best adapted to its affairs, even though such methods may differ materially from those generally adopted by others. In its financial reports it should not, however, either ask or expect that the statements it makes or the terms which it uses will be given in its case a meaning and interpretation different from that which they are ordinarily considered to have in similar reports and statements of other companies. The particular form and arrangement of such reports is a matter concerning which there may be much difference of opinion. It is of little importance whether current assets come first or last in the Balance Sheet, but it is important that there should not be included under this designation any items which are not properly current assets within the generally accepted meaning of that term. The extent to which stockholders or others interested are to be made acquainted with the full details of a company&apos;s business is a question which the proper authorities must in each case decide. It should, however, be recognized that there are certain facts regarding a mining com-pany which must be set forth in a financial statement if it is fully to cover the conditions and affairs of the company. For example, a financial, statement which does not include or is not accompanied by a statement, of the ore reserves of the company does not fully set forth its financial condition. This is true whether the absence of such a statement of ore reserves is because it is not desired to make public the figures or whether it is because the ore reserves themselves are not definitely known, or accurately measured.

Jan 1, 1928

By W. J. Keep

Cast-iron, or pig-iron, is iron which contains all the carbon that it could absorb during its reduction in the blast-furnace. As is well-known to chemists, carbon exists in cast-iron in two distinct forms. In chemical union, as "combined" carbon, it cannot be discerned, except as it may increase the whiteness of the fracture, in so-called white iron, or carburetted iron (sp. gr. about 7.72). Carbon mechanically mixed with the iron as graphite is visible, varying in color from gray to black, while the fracture of the iron, according to the color and amount of graphite it contains, ranges from a light to a very dark gray. The specific gravity of graphitic iron is about 7.40. Silicon in cast-iron is evidently to some extent combined with the iron and the carbon ; but whether it exists also in a form corresponding with graphitic carbon, mechanically mixed with the remaining mass, is a question still in dispute, which we have not in this paper endeavored to answer. It has been the opinion of many writers on metallurgy, and many foundry men, that silicon is in every way injurious to cast-iron. Yet

Jan 1, 1889

By B. N. Whittaker, C. J. Bonsall

The paper gives an account of the factors influencing the stability of coal mining tunnels and goes on to examine various bases of support and lining design of such tunnels in relation to geological and mining conditions. The different types of coal mining tunnels are compared and comments made regarding the factors influencing their choice and basic design features. Foremost amongst design considerations is the design method and special thought has been given to the validity of different formulae as related particularly to UK Carboniferous geological conditions. Emphasis is placed on the role of the stress field in relation to tunnel stability. Shape of mining tunnel has been investigated and conclusions drawn regarding the merits of different commonly excavated geometries from a stability point of view. Detailed design aspects pertaining to determination of tunnel lining strength and resulting stability are critically examined and current design methods are compared. Data from UK mining tunnels are included as the basis for comparison of these design methods.

Jan 1, 1983

BENEFICIATION AND CONCEN&apos;TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

By C. J. Rodgers

The present day success of gravel packs to prevent or retard the migration of unconsolidated sands into the well bore is due to: (I) the use of a saline or non-aqueous, nonsolids drill fluid, (2) proper preparation of the well bore prior to gravel packing, and (3) pressure placement of the gravel. The experience gained from the "pressure pack" method of gravel packing indicates that sand-free fluid production can be maintained for a length of time sufficient to make the operation economically attractive. Data pertaining to the first 15 wells so completed by Gulf indicate that for each dollar spent to effect the completion, there will be a return of more than $2.92. The pressure pack technique of gravel packing is essentially the placing of gravel in and adjacent to the producing formations. This is done with fluid pressure and by the use of a drill fluid that will permit partial or complete loss of returns to the formation during placement. This technique was first intentionally used by Gulf in May, 1950, and since that time has been applied in more than 90 wells. Other advantages claimed for this type of completion are that the pressure placement of the gravel has a scouring effect on the casing perforations, that additional drainage channels to the well bore are created, and that the possibility of shifting of the formations adjacent to the casing is minimized and possibly prevented. During the past few years, the use of gravel to prevent or retard the migration of unconsolidated sands into the well bore has met with a favorable degree of success. Numerous methods and techniques of "gravel packing" have been used, each having its own relative merits, and with varying results. M. L. Cashion1 in 1939 ably reviewed the history of gravel packing to that time. As stated in his paper, ". .. the idea of gravel packing wells is not new." During the period 1939 to 1949, very little if any progress or change in technique in this type of completion was made. However, it was noted in some cases that during the placement of gravel, if there was a loss of drill fluid to the formation, there was a corresponding loss of gravel to the formation. Also, it was noted that in those gravel-packed completions (opposite casing perforations) that "sanded up," there was found to be an absence of gravel in the annular space between the liner and casing, although gravel had previously been placed in this space and no gravel had been removed from the well at the surface. These findings resulted in the placement of gravel with fluid pressure and by the use of a drill fluid that would permit partial or complete loss of returns to the formation during placement. Pressure placement of gravel became an accepted practice in late 1949 and early 1950. Another fact brought to light that has contributed to the current success of gravel pack completions is that drilling fluids containing solids will to some extent cause plugging of the screening medium or blocking of the producing section. The removal of these solids by chemical action, mechanical action, or a combination of the

Jan 1, 1955

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly&apos; suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10&apos; to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By H. D. Merchant

NUMEROUS publications have examined hot hardness of metals and alloys. Some have studied creep in long-time hardness tests, few of which, however, were tested under a spherical indentor. 1-3 The results of Mulhearn and Tabor&apos; indicate a parabolic-type creep for indium and lead, whereas Moore and Tabor2 how a logarithmic-type creep for indium. Similar semilog relationships between hardness and time have been found by Goffard and wheeler3 for magnesium, aluminum, and their alloys. In this note, the elevated-temperature hardness of some complex alloys, shown in Table I, was examined to discover whether any basic information about the deformation behavior of the alloys could be obtained. One of the alloys, H-13 alloy steel, was tested for short-time creep tests to examine the hardness-time relationship at various temperatures. A standard Brinell Hardness Tester, mounted with an appropriate furnace and 99 pct A12O3 poly-crystalline indentor, was employed for the purpose. The alloys were tested at temperatures from room to 1400°F for 30 sec under 1500-kg load. The creep studies were conducted for about 8500 sec at 7l°, 500°, 1000°, and 1200°F. For constants A and B, a relationship of the type H = Aexp(-BT) [ll was obtained for all alloys between hardness, H, and temperature, T. In the semilogarithmic plot, the data points for each alloy were arranged into two groups, each group on a straight line with a specific set of A and B values. These results are in agreement with many such observations on hot hardness, notably those of Westbrook for pure metals,4 The thermal softening coefficient, B, and transition temperature, Tt, for various alloys are shown in Table I. The change in slope around the transition temperature suggests an apparent change in the mechanism of deformation, probably from the shear (below Tt) to the diffusion type of mechanism. At the temperatures above Tt, for constants A&apos; and B, a relationship of the type was obtained between H and T, Fig. 1. The nature of the equation, where R is gas constant, suggests the possibility of a thermally activated mechanism of deformation above Tt. The constant B&apos; may hence be defined as the apparent activation energy of indentation. The B&apos; values of various alloys are shown in Table I. A plot of B vs B&apos; gives a curvilinear relation shown in Fig. 2. The indentation-creep data for H-13 alloy steel is shown in Fig. 3. At 71" and 500°F, the creep initially follows the logarithmic time law. However, the indentation size stabilizes after 7 sec at 71°F, and after 10 sec at 500°F. Further increase in loading time has no effect on indentation size. The creep of 1000° and 1200°F follows the logarithmic time law for the first 1000 sec, after which the

Jan 1, 1964

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer&apos;s4 results. The information in Beck&apos;s compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas&apos;6 X-ray studies of Jones and Powell&apos;s specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965