Search Documents

By Oliver S. North

Reserves of perlite rock in the western section of the United States are immense. A geological report prepared for the Union Pacific RR showed proved tonnage of over 400 million tons in southern Nevada alone. Yet the perlite industry is not large, and most of the mines are relatively small. There are indications that perlite processing, thus far largely in the hands of relatively small com¬panies, is becoming concentrated in a few large companies. For economic reasons the bulk of perlite sold in crude form has come from three or four pro¬ducers, although many individual operators have sold small quantities to limited lists of purchasers. Perlite is one of ultra-lightweight aggregates. Owing to its outstanding qualities as an aggregate, variety of uses, and ultimate economy of use, it has enjoyed considerable popularity in this country in recent years. Marked foreign interest also has been evinced in this material.

Jan 2, 1955

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

The Sub-committee on Safety of the Industrial Organization Com-mittee of the Institute has been asked to cooperate with the National Safety Council, and has made certain recommendations to the Board of Directors of the Institute regarding ways and means of bringing about this cooperation. The National Safety Council has been in existence seven years. Its inception was at a meeting of the American Iron and Steel Electrical Engineers held in Milwaukee in 1912. The first annual congress was held in New York City in October, 1913, at which time the Council was definitely organized. Its membership now consists of nearly four thousand members, representing industrial plants, railroads, public utility companies, insurance companies, state labor commissions, Chambers of Commerce, manufacturers&apos; organizations, etc. These members are in all states of the Union and in eleven foreign countries, and through them the National Safety Council reaches more than six million workers.

Jan 7, 1919

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, &apos;71 1 2. Bethlehem, Pa. Aug., &apos;71 1 3. Troy, N. Nov., &apos;71 1 4. Philadelphia, Pa. Feb., &apos;72.. 1 5. New York, N. Y. May, &apos;72 1 6. Pittsburgh, Pa. Oct., &apos;72 1 7. Boston, Mass. Feb., &apos;73 1 8. Philadelphia, Pa. May, &apos;73 2 9. Easton, Pa. Oct., &apos;73 2 10. New York N. Y. Feb., &apos;74 2 11. St. Louis, Mo. May, &apos;74 3 12. Hazleton, Pa. Oct., &apos;74.. 3 13. New Haven, Conn. Feb., &apos;75 3 14. Dover, N. J. May, &apos;75 4 15. Cleveland, Ohio Oct., &apos;75 4 16. Washington, D. C. Feb., &apos;76 4 17. Philadelphia, Pa. June, &apos;76 5 18. Philadelphia, Pa. Oct., &apos;76 5

Jan 1, 1944

By G. R. St. Pierre, A. Ghosh

In the Si-C-0 system at temperatures of interest in process metallurgy there are four stable condensed phases—silicon, carbon, silica, and silicon carbide (Sic). Silicon melts at 1683oK1 and shows negligible solubility for carbon and oxygen at 1700°K. However, silicon dissolves approximately 1.5 at. pct C at 2500oK.2 Carbon in the form of graphite remains pure and dissolves negligible amount of silicon.&apos; Silica (crysto-balite) melts at 2001°K&apos; and is essentially a stoichio-metric compound. Silicon carbide is a solid and shows negligible deviation from stoichiometry up to approximately 2800oK.2 Besides the condensed phases there is a gas phase

Jan 1, 1970

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By O. B. Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos, (2) as to the principal sources of the raw material, and (3) as to the types and modes of the occurrence of asbestos.

Jan 1, 1915

By J. J. De Witte, J. G. Cazort

The Paranam plant in Surinam (formerly Dutch Guiana) was built during 1939-40 to supply crushed and dried bauxite for the growing U.S. aluminum industry, supplementing production from the Suriname Aluminum Co.&apos;s Moengo works, which began operation in 1922. A subsidiary of Aluminum Company of America, Suralco&apos;s total annual production from these two plants averages 2.55 million dry metric tons of various grades of bauxite. Starting in 1941 with bauxite from mines on the west side of the Suriname River, annual production at the Paranam plant has varied from a low of approximately 450,000 tons to more than 1 million tons in 1949. High production rates during World War II and the late 1940&apos;s rapidly depleted these reserves, and in 1950 plans were made to mine the known deposits on the east bank of the river, about five miles downstream from the original Paranam plant.

Jan 11, 1960

By Harry M. Mikami, Harold A. Heiligman

The term chromite is often used to cover all chrome ores and concentrates which are the designations actually employed by most industrial users and producers. Chromite is, of course, the predominant mineral in chrome ores which are aggregates of chromite and gangue minerals, most commonly magnesian silicates. Most chrome ores now used are petrographically chromitites which is a rock, rather than an individual mineral term. The title of this chapter, following past usage, is meant in the broad sense. Chromite is the only primary commercial source of chromium. This book is intended to deal only with nonmetallic minerals and rocks. Chromite uses are both metallic (ferroalloys) and nonmetallic (refractories and chemicals), but any discussion of mineralogy, geology, and mining is common for all types. A number of the major commercial ores are interchangeable, and their uses are determined by economic considerations. Mineralogy COMPOSITION [Chromite is a term embracing a wide range of chromium-bearing spinel*-group minerals the compositions of which can be expressed as (Mg,Fe2+)0.(Cr,AI,Fe3+ )203.t This can be further generalized to R2+O.R23+03 and the molecular RO: R,03 ratio is generally close to one. The exact composition may be arbitrarily expressed as a solid solution of six end-members, MgAI2O4, MgCr2O4, MgFe2O4 FeCr2O4, FeA12O4, and Fe2+.Fe23+04 with the proportions of each stated or plotted in the six-cornered prism of Johnston and Stevens61 or this scheme may be simplified to comprise only three endmembers making up a composition triangle, Fig 1. [ ] FIG 1-Triaxial composition diagram showing molecular compositions of chromites listed in Table 1. The RO.Fe2O3 corner includes Ti02 norms listed in the table. Note that the high-alumina chromites (1, 2, 3, 9), form a cluster well apart from the high-Cr2O3 chromites. There is a tendency for high-iron chromites to be higher in Fe2O3 + TiO2 but it is not a consistent or systematic relationship. The MgO/RO ratio must also be known to characterize the chromite chemically. Simplest and most convenient method is Thayer&apos;s&apos; in which a chromite such as (Mg.65Fe.352+)O.(Cr.40Al.50Fe.103+)203 would be written as (Mge,) Cr eAlo. The molecular pro- portions of ferrous and ferric oxides can be seen at a glance as the divalent and trivalent oxides]

Jan 1, 1960

By d&apos, C. Antonio, S. H. Reichman

In the course of our studies of the annealing behavior of vapor-deposited silver films we have determined the electrical resistivity as a function of annealing temperature for films in the thickness range of 630 to 3240A. Fig. 1 shows the resistivity of the silver films vs film thickness in as-deposited and annealed conditions. The films were prepared by depositing 99.999 pct pure silver from molybdenum boats onto Vycor substrates. Deposition was conducted at a residual pressure of 5 x 10"6 Torr at rates of 20 to 408, sec-&apos;. Thicknesses were determined using a multiple-beam interferometer. During annealing, resistance was measured using the four-probe method. Measurements were made every 5°C during two consecutive anneals to 300°C under a continuous vacuum of 2 x X6 Torr. The heating and cooling rates during annealing were approximately l° and 2°C min-&apos;, respectively. Typical resistivity vs temperature curves are shown in Figs. 2 through 4. There is an inflection point evident at 120°C on Fig. 2, the first anneal of a 3240A film. This inflection point was found on all films above approximately 1!00A on both first and second anneals. Below 1400A the inflection occurred at approximately 180°C. Figs; 3 and 4 show the first and second anneals of a 1370A film. The inflection point occurs at 180°C on the first anneal and approximately 120°C on the second. Our interpretation of this phenomenon is based on oxygen liberation from the film surface. It is well-documented that the presence of oxygen on silver surfaces causes a reversible increase in resistivity.1"3 The liberation of this oxygen, for example during vacuum annealing, would therefore cause a decrease in resistivity as observed on Figs. 2, 3, and 4 as a change in slope. This is accounted for by the decomposition of Ag20 on the film surface. The free energy of AgzO becomes positive between 125" and 225°C.4 The thickness dependence of the inflection points can be explained as an orientation effect. The films used in this study were preferentially oriented with their (111) planes parallel to the Substrate.&apos;&apos;~ In addition it has been sten that the thinner films, below approximately 1500A, possess a decided "hill and valley"

Jan 1, 1969

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y&apos; (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y&apos; morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y&apos; precipitate in

Jan 1, 1967

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-&apos;&apos;FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By R. S. Archibald

THE Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sets. 3, 4 and 5, T. 47, N.R. 28W. and sets. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 2 1/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Mar¬quette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette.

Jan 1, 1935

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By Albert Hayes

FOUR mines at Wabana, on Bell Island in Concep-tion Bay, Newfoundland, produced 1,209,777 tons of ore in 1927, and it is expected that the produc-tion will be larger in 1928. The ore is a stratified oolitic hematite of sedimentary origin. Three workable beds and many thin beds occur in a thickness of 400 ft. of interbedded sandstones and shales. It is not profitable under present conditions to mine extensively in ore beds less than 4 ft. thick. The iron ore beds outcrop on the small island and are inclined northward more steeply, than the slope of the ocean bottom. The mine work-ings follow the bedded ore below the sea bottom, No. 3 Mine extending about 2 miles north of the island. At this point there is a cover of 1500 ft. of rock and 600 ft. of ocean water. It is impracticable to operate drills in the ocean to prove the extent of the submarine orebody in advance, and diamond drilling from the mine workings is the only method of exploration. Bell Island has been settled for a long time and a monument at Cupids, near Brigus at the head of Conception Bay, commemor-ates the tercentenary of a settlement there in 1611 by Captain Guy of England. was one of the chief ports of Newfoundland for deep sea fishing and doubtless many a captain wondered about the red rocks as he sailed past. The famous geologist, J. B. Jukes, records seeing a bright red sandstone 8 ft. thick on the northwest side of Bell Island during a visit in 1842, but he evident ly did not try to land on that rocky coast to get a sample. The iron ore is plainly visible in the high cliffs along the coast of the island, as bright brown layers interbedded with gray and white sandstones and dark shales. The heavy red rock was used by the fisher-men as anchor weights for fish nets and small boats, but its real value, so the story goes, was discovered by a merchant in Saint John,

Jan 8, 1928

By Colin M. Sargent

ALTHOUGH annealing twins are frequently observed in many fcc metals, their occurrence in aluminum is relatively rare. ~ahn&apos; in his review of twinning has listed only a few references to observations of twins in aluminum, e.g., Refs. 2 and 3. They have also been shown to occur in evaporated aluminum layers.4 During the present work, several annealing twins were studied in aluminum. The specimens of 1099-grade aluminum had the following thermomechanical treatment: deformed 90 pct by rolling, partially re-crystallized, further deformed 60 pct to a final thickness of 100 p, then annealed for 24 hr at 120°C. This treatment produced several annealing twins—-about ten per electron microscope specimen. The specimens were produced by the window technique and examined in a Phillips E.M. 200 operating at 100 kv. A typical twin boundary is shown in Fig. 1. For several of the twins studied the twin plane could be tilted so that it was parallel to the electron beam, e.g., Fig. 2. The associated diffraction pattern, Fig. 3, shows the twinned relationship between the grains. The twinning plane in each case was (111). Use of a reflection common to both the twin and the matrix,* i.e., using reflecting planes parallel in the twin and the matrix, the coherent twin boundary becomes invisible and only the noncoherent segments of the stepped boundary are seen, e.g., Fig. 4. Trace analysis of the boundaries showed that the long straight portions were invariably the twin plane; i.e., these portions are coherent. The planes of the shorter segments are shown by Fig. 5 to be (551 1, (7111, and {211).

Jan 1, 1969

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r&apos;) Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r&apos;) phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y&apos;) phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7&apos;) phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y&apos;) phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y&apos;) phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

By W. H. Eatock

In its infancy, the potash refining industry in Saskatchewan was heavily influenced by practices developed in Carlsbad, NM, resulting in modern, highly productive plants. The first 15 years has been a period of reduced production, due to excessive capacity, when improvements tended to be emphasized in the mining rather than the refining functions. However, some innovations have been developed and applied in Saskatchewan and the industry is entering a period of massive expansion which will produce further advances. This paper discusses, in general terms, some of the different approaches and recent trends.

Jan 1, 1983