Search Documents

By W. G. Pfann

Under certain conditions, a molten zone can be made to move through a solid by impressing a stationary temperature gradient across the solid. This phenomenon can be utilized in fabricating semiconductive devices, growing single crystals, joining, boring fine holes in solids, measuring diffusivities in liquids, small scale alloying, and purification. Fundamentals and exemplary applications are outlined. ANEW aspect of the travel of a molten zone through a solid is considered in this paper. Whereas, in previously described zone melting techniques,'-' zones were usually caused to move by changing the position or temperature of a heat source, in the present technique a zone is made to move by impressing a temperature gradient across it. For example, a thin layer of molten A1-Si alloy, sandwiched between two silicon slabs having a temperature gradient normal to the layer, will travel through the hotter slab. One feature of temperature gradient zone melting, as this technique will be called here, is that zones of unusually small dimensions can be maintained. This leads to such diverse uses as have been listed in the abstract. In this paper fundamentals of the movement of a molten zone in a temperature gradient, and some practical applications thereof, are outlined. Assumptions The movement of a molten zone through a solid body of solvent substance in which a temperature gradient exists will be discussed. The length of the zone will be its dimension in the direction of motion. The direction of the temperature gradient will be toward the region of higher temperature. To be considered is a binary or higher order solute-solvent system in which the concentration of solute in the molten zone is sufficient to produce a lowering of the freezing temperature of the solvent which is at least of the order of the temperature range impressed on the charge. While we discuss primarily molten zones in a solid matrix, the principles are applicable to solid or vaporous zones in a solid matrix, a requirement being that the diffusivity in the zone be substantially greater than in the matrix. Diffusion of solute into the surrounding solid will be assumed negligible. In general, its presence will not basically alter the conclusions to be drawn. For illustration, a system represented by the partial constitutional diagram of Fig. la will be discussed, in which k, the distribution coefficient defined in the figure, is constant and less than unity. However, the technique is applicable to any solute- solvent system in which one component lowers the melting point of another component. Movement of a Molten Zone in a Temperature Gradient Consider, in the system AB of Fig. 1, where B is designated the solute and A the solvent, the effect of sandwiching a thin layer of solid B between blocks of solid A and placing the whole in a temperature gradient such that the temperature of the layer is above the lowest melting temperature of the system. Surrounded by an excess of A, the layer will dissolve A, becoming molten, and expand in length." As so- lution of A continues, at both interfaces, the mean solute concentration in the zone will move to the right in Fig. la, until at temperature T, the liquid at the cooler interface reaches the liquidus concentration C,. Solution of A thereupon ceases because the liquid T1 is saturated with A. The liquid at the hotter end of the zone, being at temperature T2, is not saturated with A at concentration C1. Hence solution of A continues there and concentration C2 is approached. A concentration gradient therefore is set up in the zone, causing A to diffuse toward the cool end and B toward the hot end. As a result, the liquid at the cool interface becomes supersaturated and a layer of crystalline A containing concentration kc, of B in solid solution freezes. Since a source of A

Jan 1, 1956

By J. C. Van de Water

In June the supply of M3 army demolition powder being used for mudcapping was depleted and we switched to 4 by 8, 60% Special Quarry Gelatin dynamite. This size cartridge has proved convenient, as a half stick will handle the average boulder. By keeping the gelatin in the paper while cutting it in two, there is little contact with the gelatin and therefore fewer headaches among the powdermen. To further help prevent the headache nuisance the men are furnished with plastic coated gloves. Boulder breaking costs as reported last year were $0.426 using M3. This year, 8180 boulders have been broken with M3 at a cost of $0.472 each and 7479 with 60% Quarry Gelatin at a cost of $0.660 each. This rise in cost is due entirely to the greater cost of the Gelatin as the method has not changed.

Jan 4, 1950

By H. M. Chance

The Taviche district is about 12 miles from the town of Ocotlan in the State of Oaxaca, and about 250 miles south of the City of Mexico. Its altitude rises to something more than 5,000 ft.; and although within the tropics (latitude about 17° N.) the climate is mild and salubrious, neither excessively hot in summer nor cold in winter. The phrase, "perpetual spring," which has been applied to it, aptly describes the weather during my stay. Sugar-plantations, bananas and other tropical and semitropical fruits flourish in the valleys, while the hills

Jan 1, 1905

By George Burrell

J. S. HALDANE, M. D., F. R. S., Oxford, England (communication to the Secretary?).-The valuable paper of Messrs. Burrell and Gauger is of special interest to me as, through the courtesy of the management, I had an opportunity of visiting the Portland mine, Cripple Creek, in 1911, in connection with the investigations on acclimatization to high altitudes, carried out on Pike's Peak, near Cripple Creek, by Professors Yandell, Henderson and Schneider, Dr. Douglas and myself.1 The analyses of one or two samples of the vitiated air were entirely confirmatory of those of the authors. A fatal accident owing to two men being lowered down a shaft filled with the gas had occurred in a neighboring mine just before our visit.

Jan 12, 1916

By R. G. Aspden

The cold rolling and annealing textures were studied for 3 pct Si-Fe grains initially (001) [hkl]. A concentration of (001) [loo] primaries were observed only in the annealing textures of crystals initially having [loo] within 8 deg of the rolling direction. Eke annealing textures of the (001) [I101 cold rolling textures were sensitive to the initial orientation of the grains. Single crystal data were used to explain the formation of (001) [loo] in poly-crystalline malerial. CUBE texture formation in 3 pet Si-Fe sheet occurs during the final high temperature anneal. Its formation is dependent on the proper distribution of (001) plane primaries with reference to the rolling direction&apos; and on the growth of these primaries by secondary recrystallization. The selective driving force for these primaries with (001) within 7 deg of rolling plane is derived from the difference in surface energy between the annealing atmosphere and the crystallographic planes exposed at the surface of the sheet.&apos;-= The alignment of [loo] directions of (001) secondaries with the rolling direction is required for optimum magnetic characteristics7 and is dependent on processing.&apos; A high degree of alignment has been observed when the final cold rolled texture has a strong (111) [ll2] type component3 and the normal grain growth texture prior to secondary recrystallization has components with a [loo] parallel to the rolling direction and planes from (001) to (110) parallel to the rolling plane.1,3,8,9 Generally, this (001) component is much weaker than the (110) component. The growth rate of (001) plane primaries to secondaries has been found to be independent of the orientation of the primaries with reference to the rolling direction, i.e., the secondaries have the same degree of alignment of [loo] directions with the rolling direction as the (001) primaries.&apos; Hence, the rolling and annealing textures of individual grains or single crystals are of interest in understanding the development of the (001) [loo] secondary recrystallization texture. (001) components have been observed in the annealing textures of cold rolled grains initially having a [loo] parallel to the rolling direction and an (001) rotated up to 30 deg from the rolling plane. Crystals initially near the (001) [loo] orientation when rolled under the influence of constraints imposed by neighboring grains form deformation bands and ro- tate in both directions toward (001) <110>.10,11 Deformation bands have been reported also for crystals initially with an (001) within 1 deg of the rolling plane and a [loo] within 1 deg of the rolling direction when rolled as a free single crystal.12 These crystals have weak recrystallization textures and contain near an (001) [loo] component.10-12 When near (001) [loo] crystals are rolled as free single crystals no deformation bands form and the crystals rotate by a single rotation toward (001) [110]. Recrystallization after a 70 pct cold reduction yielded near an (001) [loo] component13 and after a 90 pct cold reduction an (001) [I201 component." Crystals initially near (210) [001] had a texture after a reduction of 70 and 84 pct which was similar to the (111) [li2] but rotated 10 to 15 deg in the transverse direction. These crystals recrystallize to (210) [OOl] or (410) [001] and contain an (001) [loo] component.10,13 An (001) component has not been detected in the normal grain growth textures of other single crystals. Crystals initially having orientations between (110) [001] and (111) [ll2] have a cold rolled texture of principally (111) [ll2] .10>16 Other crystals with a [I101 parallel to the cross direction rotate to (111) [112] and/or (001) [110] stable end orientations. Crystals initially having from (001) [110] to (111) [lie] retain this orientation after cold rolling.15 The cold rolled textures having [I101 directions parallel to the rolling direction had components in the annealing textures related to the deformation textures by 25 to 30 deg rotations about common (1 10) poles. Cold rolled textures of the (111) (112) type recrys-tallized to (120) [001] or (110) [00l]. The purpose of the present work was to further the understanding of the alignment of [loo] directions of (001) secondaries with the rolling direction. The cold rolling and annealing textures of grains initially (001) [hkl] were studied. These data were applied to the formation of (001) [loo] by secondary recrystallization. PROCEDURES AND EXPERIMENTAL TECHNIQUES The (001) poles near the sheet normal and rolling direction are given in Fig. 1 for the 10 grains studied. Each of these grains was located in the center of a polycrystalline specimen approximately 25 mm wide and 50 mm long. The lower case lettered grains, a through dl were about 1.2 mm in diam and near the (001) [loo] orientation. Specimens containing these grains were from a commercial 3 pct Si-Fe alloy with the principle orientation of (110) [001] as obtained by impurity inhibition of growth with manganese sulfide inclusions.17,18 Upper case lettered grains, A through F, were about 6 mm in diam and had (001) planes near the rolling plane and [hkl] di-

Jan 1, 1963

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,&apos; and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.&apos;" Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence.

Jan 1, 1955

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry-a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal involves environmental protection and the economics of refuse handling. For over two years, Monterey Coal Co. has operated a non-polluting refuse disposal system at its No. 1 Mine located in Brushy Mound Township of Macoupin County 6 miles south of Carlinville, Illinois. Drainage goes to Spanish Needle Creek and eventually to the Illinois River. The mine produced 3.5 million tons of clean coal during its first two and one-half years of operation and is designed to produce 3 million tpy of clean coal at capacity.

Jan 6, 1973

By H. A. Koch, R. L. Slobod

This paper discusses a new oil recovery process called the "miscible slug process." This process involves the injection of propane or LPG into the reservoir prior to gas injection. The operating conditions are maintained so that the slug is miscible with both the reservoir oil and the injected gas phase. Thus, a miscible phase displacement is achieved, and high recoveries are obtained from the area of the reservoir contacted. The most striking discovery of the laboratory study which included displacements from cores up to 123 ft in length was that relatively small slugs of LPG are effective over reservoir distances in the miscible displacement of oil. This makes possible the commercial application of the process. The important factors controlling the size of the slug are: (I) reservoir length, (2) reservoir fluid composition, and (3) reservoir pressure at the displacement front. Of lesser importance are the effects of injection rate and porous medium type. Questions which have not been completely answered deal with the effects of gravity and reservoir inhomogeneities on the process. INTRODUCTION One of the major problems facing the oil industry today is recovery of the large fraction of the discovered oil which will remain unrecovered unless some new processes are found. Water flooding has been one successful method used to increase recovery over natural depletion. But even successful water floods may leave 25 to 40 per cent of the pore space filled with residual oil. Recently a process which involves the use of thermal energy has been reported1,&apos;*&apos; which may prove useful in increasing recovery from shallow reservoirs containing highly viscous crudes. This paper deals with a new oil recovery process involving use of miscible phases to displace the oil from the reservoir. Miscible phase displacement oil has been an intriguing idea because the elimination of capillary effects in the reservoir leads to 100 per cent recovery in the areas contacted by the miscible displacing phase. The big deterrent in the past to the practice of miscible phase displacement has been the high cost involved in using large volumes of solvent in the process. The use of high pressure gas to achieve a miscible phase displacement of reservoir oil has been reported4,5 as one economically feasible method. However, this process calls for the maintenance of pressures above 3,000 psi at the dis-placement front. The process described in this paper is not restricted to high reservoir pressures; the only qualification being that the slug of material which is injected into the reservoir must be miscible with both the displaced oil 2nd the displacing phase. Two such cases are the use of an alcohol slug followed by water to achieve a mis-cable water flood, and the use of a low boiling hydrocarbon slug such as propane followed by gas to achieve a miscible gas drive. This paper will deal specifically with the propane dug process. This process will obtain a miscible phase displacement at pressures as low as about 1,200 psi at a reservoir temperature 01 150°F. The process is very simple. The propane displaces oil completely at one front because it is miscible with the oil, and gas displaces the propane completely at a second or trailing front because it is miscible with the propane. A small band of propane should thus remain wedged between the gas and oil phases. This idea has been called the "miscible slug process."6 Unfortunately, the propane slug will become diluted as it flows through the reservoir. This results from a mixing action since the fluids flow through a complex reservoir porous medium rather than simple capillaries. Fig. 1 diagrams a miscible slug displacement. The effects of some of

Jan 1, 1958

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper&apos; by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

By P. Somasundaran

An experimental and theoretical treatment of the depressing effect of inorganic electrolytes on the amine flotation of quartz is presented. Experimental data obtained for the amine flotation of quartz as a function of pH with potassium nitrate as depressant was used to test the models for the effectiveness of inorganic ions as depressants. The validity of commonly used assumptions are examined. The surface tension data obtained for dodecylammonium acetate solutions as a function of KNO3, concentration indicated that the collector adsorption on bubble cannot be neglected in the treatments, since this adsorption changes significantly with the addition of the inorganic electrolyte. It also indicated the possibility of significant changes in the specific adsorption potential of the collector occurring with the addition of inorganic electrolytes.

Jan 1, 1975

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971

Jan 1, 1940

J. B. MCGRAW, New York, N. Y. (written discussion*).-In Mr. Burke Baker&apos;s description of the process of the American Briquet Co., he speaks only of the attractive features, but every process which uses a compound or emulsified binder has certain undesirable features which must be considered. In making an emulsion, the success of which depends upon the introduction of the various ingredients at certain fixed temperatures and the complete intermixing of a soluble solution with an oil which has absolutely no affinity for it, considerable difficulty is found in keeping the various factors in strict accordance with the formula. To serve its purpose properly or, in other words, to be right for easy mixing with the coal, it should be of a certain predetermined density. Among the controlling factors of this ate the proportion of moisture contained and the temperature of the oil when introduced. If the latter is higher than intended, a greater proportion of moisture will be evaporated than is proper, and if the oil is not sufficiently hot the process of emulsification is retarded. These various factors can be controlled with more or less certainty where working in a laboratory or in a small experimental way, but when it is attempted on a large commercial scale, certain obstacles not otherwise apparent are likely to be encountered.

Jan 5, 1918

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne&apos;s statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By Eugene McAuliffe

The mining press, as well as certain federal and state bulletins, refer from time to time to the relative hazards that attach to loading bituminous coal by hand when compared with the so-called "mechanical loading" process. Much of the coal coming under the head of hand-loaded coal is won in part by the use of machinery; the coal-cutting machine is in general use, the electric power drill employed to a lesser extent. Therefore it may be said that the principal difference in the process employed, mechanical loading versus hand loading, lies in the fact that some type of loading machine is employed in the mechanical loading process to lift the coal from the face of the room, place or entry, after it is mined, placing it in the pit cars for transport to the tipple. It is a common practice to compute accident records on the basis of tons mined per fatal and per nonfatal accident, disregarding the fact that it is possible to produce by the aid of coal-loading machines the same daily, monthly and annual tonnage with a much smaller force than is required where the coal is all shoveled by hand. Inasmuch as the men who are released by the substitution of machinery for hand labor must find employment elsewhere, suffering some measure of hazard in their new occupation, we are of the opinion that the true relative hazard that attaches to the processes of mechanical loading and hand loading can be determined only by using as the basis of comparison "man shifts worked" or "hours of exposure" experienced per accident. The Union Pacific Coal-Co., beginning with the year 1929, undertook to maintain a true record of man shifts worked per compensable accident, giving equal weight to fatal and nonfatal accidents. Accidents lacking sufficient severity to come under the compensable terms of the Workmen&apos;s Compensation Act were not included in the compilation, the Act providing that "no compensation, except the expense of medical attention, shall be allowed for the first seven (7) days of disability, unless the incapacity runs beyond the period of twenty-one (21) days, in which case the compensation shall run from the time of the injury." With the further thought that all accidents suffered by employees engaged in any service, in or about the place where the loading process

Jan 1, 1931

By A. Tanaka, K. G. Carroll

The existence of local room-temperature plastic flow in germanium, which has been a subject of controversy for nearly two decades, has recently received renewed attention, albeit no more agreement than hitherto. Phenomenologically one major facet of the problem has been reduced to the question whether or not indentation can be effected in germanium without the introduction of cracks. That plastic flow can be induced at room temperature by fracture appears to have been rather convincingly demonstrated recently by Suzuki and Kamada and by Noble and Henisch.1 The literature contains both direct and incidental references to Vickers and Knoop indentations showing no cracks, within resolution of optical microscopy. Recently, however, following a controversy on the subject,2,3 johnson4 made a study of indentations produced by spherical indenters and concluded that these are accompanied by cracking. This study in-

Jan 1, 1969

By Burt A. Waite

The new OSM regulations for ground water monitoring of underground coal mines have been the source of many concerns for the mining industry. Because the regulations were initially written at the federal level, but are being administered at the state level, considerable confusion still exists within the industry as to what is really required. Based on submission and/or approval of more than 30 monitoring plans for existing mines in Pennsylvania, West Virginia, and Ohio, three basic sections are necessary. They are: 1. background data on the hydrogeologic setting of the mine, 2. the monitoring plan itself, and 3. mining procedures to minimize adverse effects on ground water. Like all of the OSM requirements, ground water monitoring will be a new burden the coal industry must bear, but with proper planning and communication with the regulatory authorities it need not be as bad as originally feared.

Jan 1, 1983

By FORTUNATO PEREIRA

(San Francisco Meeting, October, 1911.) I. GENERAL DESCRIPTION. The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, FIG. 1.-SKETCH-MAP OF THE SOUTHWESTERN PART OF COLOMBIA. near the boundary of Ecuador, as shown in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the principal towns are Túquerres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Aug 1, 1912