Search Documents

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

SAMUEL L. HOYT.-The question of adding the ferromanganese to the ladle or to the furnace involves both theoretical and practical questions and its discussion might very easily occupy the rest of the day. One of the points to be kept in mind is the desirability of obtaining uniform steel. If ferromanganese is added to the ladle, it is necessary first to melt the manganese and then to distribute uniformly throughout the heat. The only heat available for this purpose is that of the molten steel itself. No doubt sufficient heat is present, but in our desire to pour the steel as quickly as possible there is hardly sufficient time allowed, many times, for the proper distribution of the manganese. In other words, this is an operation which takes a certain amount of time and any undue shortening of the time allowed must affect the quality and uniformity of the steel. Again, this particular method does not lead to as efficient a use of the manganese as might be desired; a contention which is based on theoretical grounds. In concentrated solution, manganese will completely reduce all the ferrous oxide, the presence of which I hypothecate and produce, as the reaction product, manganese oxide. In dilute solution, the manganese only partly reduces the iron oxide, but the manganesee oxide which does form dissolves the iron oxide in simple solution. The dissolution of ferrous oxide in the manganese oxide will result in a more economical utilization of the manganese and an equal purification of the heat. This whole point, at present, has not been definitely proved and its answer will involve very difficult research work. On the other hand, if the manganese is added to the furnace, the heat of the furnace is used to melt the alloy and there is plenty of time during tapping for the manganese to be very uniformly distributed throughout the steel. By distributing the alloy throughout the charge we can secure a better utilization of the manganese than is possible if the addition is made to the ladle. Certain other points, such as the recovery, have been dealt with at greater length in the paper.

Jan 4, 1919

By Nicholas J. Palethorpe

BACKGROUND Before addressing the above topic in any detail, it is pertinent to provide some background on Australia for those people who have not been there or who have a limited knowledge of our continent. Australia is approximately the size of the continental U.S.A. (excluding Alaska) covering an area of approximately 7 million square kilometres. It has a very dry climate which has led to a concentration of people in major cities scattered around the continents perimeter. Australia's population is currently approximately 15 million. Of the work force of 6.3 million, 72% work in tertiary industries, 20.2% in manufacture, 6.5% in agriculture and 1.3% in mining. Agriculture accounts for 46% of exports, mining for 31% and manufacturing for 23,. Economic activity is based on:- Agriculture This is capital intensive and covers extensive areas and is reliant on low cost farming. A.range of foods and fibres are produced with over 70% of production being exported. Such products are of course subject to the usual vagaries of world market demand and market access, particularly in regard to the operation of trade blocks such as the E.E.C. Mineral Resources A wide range of minerals and an abundance of iron ore, coal, gas and uranium resources provide an increasing volume of exports. However, Autralia's oil resources at present only supply approximately 70% of local requirements. Industry This is diverse and encompasses the processing of agricultural products and mineral ores as well as helping to supply the consumer and capital goods needs of the whole community. However, the small scale of local markets, the geographic isolation of Australia and relatively high wage costs have limited the scale of Australia's industry. Advanced technology has overcome some of these difficulties and high tariff and import quotas protect local producers from the full force of international competition. In 1980/81 Australia's Gross Domestic Product amounted to $130 billion with approximately 24% of this being devoted to investment. In the past decade Australia has experienced inflation rates ranging from 5% to 17% and only modest real growth rates ranging from 0.4% to 5% per annum. We have also experienced, as have many other industrialised nations, continuing wage and price increases. Unemployment presently stands at 6%. MINERAL DEVELOPMENT As the above figures indicate, Australia's continuing prosperity is very dependent on the mineral and agricultrual sectors of our economy. The dependence on these sectors is highlighted by the table below which indicates our position in a global context. [Australian Production of Minerals in a World Context Western World % Total Western World Position Mineral Production 1980 1st Rutile 75 Ilmenite 31 Zircon 70 Bauxite 36 Iron Ore 11 Tungsten 14 2nd Lead (Conc.) 15 3rd Manganese Ore 14 Brown Coal 11 (1979) Zinc (Conc.) 10 4thSilver (Conc.) 10 Nickel 6 5th Tin (Conc.) 5 6th Black Coal 5 Gold 2 Source: Mining Annual Review 1981] The total value of all mineral and fuel exports in 1980/81 is estimated at $5.9 billion. This prominence in the world mineral production has largely been achieved in the last 15 - 20 years. In fact, in the early 1960's, Australia had only 2 major mining export centres, Broken Hill in New South Wales and Mt. Isa in Queensland. This growth is highlighted by the fact that in 1963, for example, we exported only 9 tonnes of iron ore and less than 4 million tonnes of coal. In 1980/81 we exported 75m. tonnes ',of iron ore (valued at $1,117m.) and 47m. tonnes of coal valued at $1,965m.). The growth in our mineral industry has come about because of a number of factors. Abundance of Mineral Resources We are particularly well endowed with mineral resources, as indicated below.

Jan 1, 1982

By Frederic A. Delano

In adding one more to the list of papers that have been presented on the subject of steel rails, I wish to explain at the beginning that in enumerating the steps in the manufacture which, I think, have an all-important effect on the wearing-qualities of the rail produced, I do so with no little hesitation. As a student in the field, I am anxious for the opinions of others, and have finally decided to ask for it in this way. I have not stated everything which I think affects, in one way or another, the life of rails, but have confined myself to those steps in the manufacture which I felt most sure did do so. Recognizing the danger of being carried away by enthusiasm, I have endeavored to make my assertions with caution, and to understate my case rather than to overstate it; but if I have succeeded in throwing a ray of light on this vexed question and placed it in the eyes of some railroad men in an aspect which they have not fully considered, my boldness will be more than justified. I. Uniformity in the quality of the material charged into the converter assists the attainment of uniformity in the steel produced.— This is the argument which is used by the champions of the cupolamelting or indirect process, and has considerable weight. It takes vastly more skill to make good steel if there is a great irregularity in the iron charged into the vessel than if there is not this irregularity ; but on the other hand, there are certain advantages in the direct method, such as a lower sulphur-percentage from the same furnace-iron, while it is possible to get as great uniformity in the iron charged by having the furnace-capacity enough in excess of the demands from the converting department, to allow for occasional " slips " in the furnaces, and permit the mixing of the iron from two furnaces which are respectively too " hot" and too "cold." 11. Care in pouring ingots at the proper temperature into warm moulds, and the treatment of ingots before rolling, have important effects on the rails made from them. In other words, many of the failures in rails and the uneven wear of rails are often traceable to

Jan 1, 1888

By W. V. Youdelis, W. H. Bear, G. Cochrane

HERETOFORE, there has been very little study of the effects of various metallurgical factors on the behavior of thermoelectric materials, the need for which is evident if optimum processing and design of thermoelectric devices is to be realized. Accordingly, we have undertaken such an investigation on the thermoelectric materials bismuth and Bi-Sb alloy and in this paper present some preliminary results which merit consideration, in particular the relatively high thermoelectric power and figure of merit values obtained for the Bi-12Sb (at. pct) alloy powder compacts. The thermoelectric parameters for ingot and powder compact specimens are determined and the results are compared with published data for single crystals. Preparation of Materials. The bismuth and antimony used in this investigation are six nines pure. Melting and casting of the ingots was carried out in air for expediency, since most oxidation unavoidably occurs during the preparation of the powder by filing of the ingots. Chill cast ingots of pure bismuth were prepared by pouring the melt into split copper chill molds, and unidirectionally solidified ingots of bismuth and Bi-Sb alloy were obtained by slow directional cooling in pyrex tubes. All melts remained bright during melting and casting, indicating minimum oxidation. Powder for the powder compact samples was obtained by filing the ingots with a fine and coarse file to give a variation in the particle size of the compacts. The particles in the fine powder compacts varied in size from approximately 28 pct less than

Jan 1, 1970

Jan 1, 1920

By Molly Gleiser

The standard free energies of formation of some gaseous metal oxides together with those of their condensed oxides have been plotted against temperature. The heats of formation of the gaseozcs oxides are tabulated. An explanation is given of the use of the data to predict the importance of the gaseous metal oxides at high tenzperatures. RECENT mass spectrometric work1 has resulted in the detection of several hitherto unknown gaseous oxides and the measurement of their free energies of formation. Of especial interest is the fact that several of the refractories in common use either as crucibles or furnace tubes, and metals used in Knudsen cells and in furnace windings, have been found to have one or more stable gaseous oxides. In view of the present emphasis on high-temperature techniques, the development of vacuum metallurgy.z heating by electron bombardment and plasma jets, and the resultant shift to ever higher temperatures, it is no longer possible to plan experiments without taking into consideration the significance of the presence of these gases in the system, the reactions they undergo. and their contribution to the vapor pressure. A good example of what went wrong in earlier work, when the existence of these gaseous molecules was not yet known, is presented by the work of Hoch, Nakata, and Johnston. Hoch and coworkers attempted to measure the vapor pressure of solid ZrO2 by letting the vapor in equilibrium with zir-conia effuse from a tantalum Knudsen cell. The free energies of formation of solid zirconia and tantala are such that a short calculation showed that the reaction

Jan 1, 1962

By A. S. Richardson

PROGRESS in health and safety in the mining field has been greatly affected by war conditions. Some of the instruments commonly used in ventilation and dust prevention work have been practically unobtainable. Much equipment, such as fans, has been purchasable only when it was possible to make positive statements to the effect that it was absolutely necessary for the production of definite quantities of materials essential to the war. Even then, long delays were usually experienced in obtaining such equipment from the manufacturers. These circumstances have, of course, not been conducive to the development of new and better methods, though attention has been directed by governmental agencies towards the recognition of existing hazards to which little attention had previously been paid.

Jan 1, 1945

Executive Committee. GEORGE F. KUNZ, Chairman. E. GIBBON SPILSBURY, Vice-Chairman. THOMAS ROBINS, H. J. SEAMAN. Louis D. HUNTOON, Secretary-Treasurer. Meeting, Apr. 4, 1913. A joint meeting of the New York Section of the American Institute of Mining Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers was held in the large auditorium of the Engineering Societies Building, 29 West 39th Street, on Friday evening, Apr. 4, 1913, and an exhibition of the Edison Talking Moving Pictures was presented before the Societies, together with exhibitions of the work which is being done by the Edison Co. in making moving pictures to illustrate lectures on natural science and the useful arts for school and college work. Introductory remarks were made by Mr. J. W. Lieb, Jr., and followed by an exhibition of moving pictures illustrating the formation of crystals, the operation of different types of pumps, magnetic forces, electro-magnetic separation of iron ore, the evolution of the fly, and many other most interesting studies. One of the films, entitled The Formation of Crystals, showed a moving picture of a boy, whose laboratory was the kitchen, dissolving salt in a test tube filled with hot water. The boy then poured the solution of hot salt into a watch glass and placed it under the microscope to watch the crystals form. This film was immediately followed by another showing what the boy saw through the microscope. The solution at first was free from crystals. Gradually the crystals commenced to form and increased very rapidly after once starting, shooting across the screen with lightning speed. The film illustrating the separation of iron ores by the Edison electro-magnet showed an ore bin with an electro-magnet set at one side and below the bin. As the ore was dropped from the bin the magnetite was drawn into the. electric field and deposited in a separate rile from the sand.

Jan 5, 1913

By Gerald Edmunds

IN a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical change in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained-i.e., (001) parallel, ±20°, to the surface-as was obtained when it was cast against air, Transite or iron.1 Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about ¼ in. of lead, then) ½ in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 1 ½ in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,1 with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two ¼ -in, diameter aluminum-alloy die-cast tensile bars and on a 1/8 by ½ -in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at-the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. SUMMARY A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. ACKNOWLEDGMENT The X-ray determinations were conduced by M. L. Fuller.

Jan 1, 1945

The Reconstruction and Research Division of the United States Council of National Defense has, up to date, prepared two reviews on the above subjects: one covers foreign countries and the other covers the activities in the States. These reviews contain information appearing in various Governmental and public periodicals. While the information on foreign countries is necessarily incomplete and fragmentary, its summation is perhaps the most complete work of this kind so far accomplished. The information from the states consists mainly of bills and ordinances introduced in the state legislature, municipal councils, legislature committee reports, programs suggested by governors, and other state and local officials and local organizations It is realized that a good deal of this information will be useful to engineers studying conditions in the various states, and especially to those who want an insight into the general condition in all the states. For instance, the reconstruction problem in each state involving highway, reclamation, buildings, etc., are covered in detail.

Jan 8, 1919

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The officers of the Institute whose terms expire are as follows: President, William L. Saunders (not eligible for re-election). Past President, Charles F. Rand. Vice-Presidents, Thomas H. Leggett, District 0; Fred W. Denton, District 4.

Jan 9, 1915

The Joint Economic Committee's subcommittee on international payments and exchange has recommended that, following international monetary reforms, the law which prohibits private possession of gold by American citizens be repealed. The subcommittee recommendation called for reforms to enhance the role of special drawing rights in international monetary affairs and downgrade the role of gold. Special drawing rights, also known as "paper gold", are on artificial reserve with the International Monetary Fund (IMF) which distributes them to member nations in proportion to their economic importance in the world economy. The special drawing rights are then used to settle debts between nations in the same manner as gold or currency. The subcommittee said that under the reforms now being discussed special drawing rights would be acceptable in lieu of gold among the member countries of the IMF.

Jan 1, 1973

By A. C. Fieldner

THE COMMITTEE on Correlation of Research held two meetings in 1931. The first was a luncheon meeting on Feb. 19, at the Engineers Club, New York, attended by eight members and four guests-William H. Bassett, past-president of the Institute; Robert E. Tally, president; H. Foster Bain, secretary; and Alfred D. Flinn, director of the Engineering Foundation. Mr. Bassett gave a short resume of the circumstances leading to the formation of the Committee and expressed his opinion that the objectives as expressed by the Committee in its first annual report were in accordance with the ideas of the Institute officials. Mr. Tally stressed the great importance of research in the mining and metallurgical industries and stated that lie believed the Institute should encourage and promote research, and that this Committee could do a great deal to foster such work in the Institute. Mr. Bain pointed out that this Committee was appointed with a view to correlating and fostering research work. in the field of the Institute's activities. This could be done in various ways, as by encouraging the divisions and committees of the Institute to hold group meetings on research, by forming research subcommittees in the Institute divisions, and by bringing together research interest in. certain projects and the fund or organization that is equipped to carry out the project.

Jan 1, 1932

SOUTHERN CALIFORNIA LOCAL .SECTION Executive Committee SEELEY W. MUDD, Chairman C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER The Southern California Section, held a dinner and meeting at. the Sierra; Madre Club, Los Angeles, on Friday evening, Sept. 28, 1915, at which 21 members and guests-were present. The Vice-Chairman, C. Colcock Jones; presided, in the absence of the Chairman. The amendment' to the By-Laws providing for the increase of the Executive Committee from five to seven members, having been formally presented at the annual meeting of June 18, 1915, and duly announced for consideration at this meeting, was voted on and unanimously adopted. Prof. Robert H. Richards of the Massachusetts Institute of Technology; made a short address on the subject of ore concentration. The paper on the Geology and Ore Deposits of Mojave, County, Arizona, prepared by F. C. Shrader, was presented to the meeting by the Secretary and was discussed by Allen Burris and Dr. L. D. Godshall. F. J. H. MERRILL, Secretary.

Jan 11, 1915

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Extensive solid solubilities of CdTe (zincblende-type struckre) and InTe (B37 type) in each of the rock salt-type compounds, PbTe and SnTe, have been observed. Partial phase diagrams have been determined by thermal analysis and X-ray metallography. The limiting mol fraction. X,, of the solute in the rock salt-type a phase and the corresponding eutectic temperatures, T,, are: (PbTe)l-x(CdTe)x: X,- 0.2, T, =866°C; (PbTe),-,(lnTe),: X, - 0.35, T, = 646"C; (SnTe),-,(CdTe),:X,- 0.11, T, = 784 "C; (SnTe),-,(lnTe),: X,-0.53, T, = 630°C. The lattice parameters of the a phase decrease linearly with X, even in (PbTe),-,(CdTe),, where a, (CdTe) = 6.481A > %(PbTe) = 6.459A. This is taken as proof that the cadmium atom enters an octahedral interstice of the tellurium atom sublattice; i.e., the formation of the a phase entails the direct replacement of lead by cadmium. The a, us X curve extrapolates to 6.16A at X = 1, in agreement with the value predicted for an ionic crystal of CdTe; it is also consistent with the reported lattice parameter It is well-established that the compositions of intrinsic semiconducting and semimetallic compounds conform to normal valence rules.1"5 The apparent exceptions can be explained by taking account of anion-anion covalences, as in CdSb, or of multiple cation valences, as in In Te.'This empirical generalization is the basis of the chemical approach to semiconductors2 by which the properties of an intrinsic semiconductor are rationalized in terms of the ionic-covalent bonds necessary to saturate the valence-electron complement of the anion sublattice. A fundamental shortcoming of this approach is its disregard of long-range crystal interactions. It cannot, accordingly, deal with the phenomenon of charge conduction except through the use of ad hoc postulates. As an example, a crystal of CdTe would, in the valence-bond picture: be described in terms of electron pairs, each with the same discrete energy, localized between every cadmium and tellurium atom. This is, of course, contrary to the Pauli of the high-pressure rock-salt form of CdTe, corrected for decompression from 36 kbar. The free energy of formation of the a phase of pure CdTe at room temperature is calculated from the phase diagram to be +10 kcal per g-atom, in accmd with the value calculated from the transformation pressure. The standard enthalpy is +13 kcal per g-atom, and the standard entropy is +9 eu. The latter value implies the formation of extra classical particles, such as vacancies, interstitials, or nondegenerate charge carriers, but these alternatives are not consistent with the semiconducting properties and the densities of the a phase. The extrapolated values of the lattice parameters of (PbTe),-,(lnTe), and Spectively, for the rock salt-type modification of InTe. The corresponding interatomic separation is intermediate between monovalent and trivalent indium. The qualitative implications of the results are considered from the viewpoints of both valence-band theory and energy-band theory. principle, and is corrected by methods of molecular-orbital theory in which bonds are replaced by bands of molecular orbitals whose energies, E, depend upon a crystal-momentum vector, k.7 Each band is derived from a linear combination of atomic orbitals with two electrons required to saturate each molecular orbital in the band. In a crystal of N atoms containing z atoms in its primitive unit cell, there are 2 N/z states per band which lie in a region of k space bound by the Brillouin zone. In an intrinsic semiconductor, the bands can be grouped into valence bands which are normally filled and conduction bands which are normally empty. If the highest valence band and the lowest conduction band overlap anywhere within the Brillouin zone, the material is rendered semimetallic. The quantity defines the effective mass, m*, of an electron in a conduction band (or of a hole, i.e., an electron deficiency, in the valence band) and leads directly to the concept of charge mobility through the relation \x = et/m*, where e is the electron charge and t is the lattice relaxation time.

Jan 1, 1964

"Copper was first made in Butte by the use of iron for its precipitation from mine water in 1890. In consequence of a fire breaking out in the St. Lawrence mine of the Anaconda Copper Mining Company in November, 1889, a large quantity of water was poured into the workings, with the intention of flooding the mine and extinguishing the fire. This proved to be impracticable, but this water, on being pumped to the surface, was found to be high in copper sulphate,—tradition says 75/100 of 1 per cent. The Anaconda Copper Mining Company gave Wm. Ledford a lease on this water. He first (lug holes into the ground, filled them with scrap iron and allowed the water to flow through them. Later he built an open-top flume which he partially filled with iron and passed the water through the by the iron precipitation method. An assay in- the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level.None of the mine waters encountered in the solid rock in the mines of Butte contained copper in sufficient quantity to produce the metal profitably by the iron precipitation method. An assay in the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level."

Jan 1, 1913