Search Documents

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By J. E. Brantly

THE oil-producing industry may logically be &apos;divided into four independent branches: (1) Acquisition of possible productive lands by lease, fee purchase, concession, or otherwise and the perfection of titles thereto. (2) Studies of the geology of the properties, leading to the location of exploratory wells. These involve reconnaissance and detailed surveys and the use of geophysical instruments, where conditions do not permit surface determination. (3) Drilling of exploratory or test holes and, later, exploitation wells. (4) Actual recovery of the oil from the wells by flowing, pumping, or other methods. These four divisions of the industry are unrelated in detail of accomplishment, but they are entirely complementary, one to the other, and must, in any efficient&apos; organization, harmonize in their respective efforts toward the desired ultimate end. The relative order for the first two branches is not necessarily the proper one; in fact one should have knowledge of the favorable possibilities of a given property before it is acquired, and preferably, also, final opinions as to then proper location for an exploratory well, if such is justified in the light of

Jan 1, 1937

E. Windsor Richards, London, England:—In reading this paper the most interesting point to me mas the question of the maximum percentage of phosphorus allowable in the steel rail. Mr. Colby said, and we will all agree with him, that the engineer knew, and even a steel-rail maker grants that phosphorus is the most undesirable constituent of steel. We in England have been for a long time considering a specification for the supply of steel rails. This matter has been taken up by the Institution of Civil Engineers, the Mechanical Engineers, the Iron and Steel Institute, the Institute of Naval Architects, and the Electrical Engineers. Committees have been formed,and the whole matter has received most careful attention. They arrived at last at an analysis which I will read: " The carbon is to be from 0.35 to 0.5 per cent.; the manganese from 0.7 to 1.0 per cent.; the silicon, not to exceed 0.10 per cent.; phosphorus, 0.07; and sulphur, 0.07 per cent." As to the phosphorus, which is the most important point of all in the analysis, we have for many years, and indeed until very lately, always agreed to supply steel which would not contain above 0.06 per cent. of phosphorus. Iron-ores are not quite as good now as they were formerly, and the manufacturers at the meetings of the committees referred to, tried to obtain an increase in the allowance of phosphorus. They asked the Sub-committee to agree to 0.08 per cent. of phosphorus. They tried all they possibly could to obtain that; but they failed. English engineers in Great George Street and all over England, representing the important Associa tions I have mentioned, would only agree to 0.07 per cent. and that is the maximum allowance of phosphorus. Mr. Colby is an able advocate, but with all his ability he would not have been able to persuade the English engineers to agree to 0.08 per cent.

Jan 1, 1907

By AIME AIME

LEWIS EMANUEL YOUNG was elected a Director of the A.I.M.E. at the last Annual Meeting as a representative of District &apos;4, including. Ohio, West Virginia, and western. Pennsylvania and New York. He also represents the Coal Division, in which industry lie has actively participated- for nearly twenty years. Dr. Young was horn in Topeka, Kan., Oct. 1, 1873, received mining degrees from Penn State and ,-Iowa. State, and a Ph.D., from Illinois. The first part of his professional life was spent in teaching first as instructor in mining at Iowa State, second .as professor of mining at the Colorado School&apos; of Mines, third as director of the School of Mines and Metallurgy at Rolla, Mo., and finally he taught business

Jan 1, 1937

By Myers, J. F.

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the lsabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.&apos; Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test- runs were made with the four different pinions. The screen analysis of each of the thee-week run samples at the various speeds were composited and the results are shown in Table 1. The authors feel that the 12 weeks of operation consumed during these test-runs would represent fairly the effect of each mill speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds.

Jan 1, 1949

By W. F. Hosford

A series of aluminum single crystals was subjected to axially symmetric flow by drawing through dies. The orientation dependence of the drawing stress, which indicates the resistance to this type of flow, compares reasonably with predictions of Taylor and of Bishop and Hill. Measured lattice rotations likewise are generally consistent with theory. The most successful analyses of the plastic behavior of polycrystalline metal and its relationship to single crystal behavior are those of Taylor1-3 and of Bishop and Hill.4-6 The purpose of this paper is to provide a critical test of some of the basic assumptions involved in these theories. Both treatments apply to fcc metals and assume the shape change of each grain in a polycrystal to be the same as that of the polycrystal as a whole. Thus for a randomly oriented polycrystal extended under uni-axial tension each grain is assumed to undergo axially symmetric flow. dey = dez = -1/2dex, deyZ = dezx = dexy = 0 [l] where x, y, and z are a set of orthogonal axes, x being the tensile axis. Although [011.] oriented grains in bcc and fcc metals may depart markedly from this ideal behavior,7,8 the assumption is probably quite reasonable for most grains. Under a uniaxial tensile stress, ox, the work dW per unit volume expended in producing an increment of axial strain dex is, dW=oxdex [21 Since this work is expended in slip, dw =STi dyi 131 where Ti and yi are the shear stress and shear strain on the active slip systems. In both analyses Ti is taken to be the same on all slip systems, and dependent only on the total prior shear strain on all systems, so dw = Tdy [41 where t is the shear stress required for slip and y is the sum of the shear strain yi on all slip systems. Combining 121 and [4] and defining M = oX/T The ratio M is a generalized Schmid factor. It relates the tensile stress required for axially symmetric flow, ox, to the basic shear stress, 7, and it also expresses the ratio of crystallographic strain, y, to the tensile strain, Ex It depends only on the orientation of the crystal. Taylor evaluated M for various orientations by finding the least value of dy/dEx which could satisfy the shape change. Bishop and Hill, on the other hand, found M by considering the relative work (1/T)dW/dEx expended by stress states which could activate enough slip systems to produce the shape changes. The results of both methods appear to be equivalent, although certain omissions were made in Taylor&apos;s original work. The orientation dependence of M, calculated by the second method,9 is shown in Fig. 1. Taylor used the average 2= 3.06 for all possible orientations to predict the tensile stress-strain curve (oxvs Ex) for a random polycrystal from the shear stress-strain curve (t vs y) of a single crystal. Changes in M from lattice rotation were neglected so points on the ox vs ex curve were simply taken at ox = 3.06t and e = y/3.06 from corresponding points on the t vs y curve. Recent extension of the analyses of Taylor and of Bishop and Hill to crystallographically textured metals has been used to relate plastic anisotropy to textures, and to predict the potential texture hardening that could result from texture control.9 Unfortunately there have been relatively few experimental tests of the underlying theory. Taylor found that the tensile stress-strain curve of polycrystalline aluminum did agree reasonably well with that predicted from a single-crystal T-y curve. Had the single crystal undergone easy glide, how-

Jan 1, 1965

By F. R. Brotzen, D. L. Davidson

ALTHOUGH much effort has been devoted to the problem, the nature of plastic flow in bcc metals is still not fully understood. Some of the difficulties encountered stem from the scarcity of information on orientation effects and the uncertainty as to the glide system in these metals. In an attempt to provide some of this information, the present investigation was carried out, using zone-refined molybdenum single crystals deformed in tension and in direct shear. Considerable evidence exists to indicate that the primary slip system for molybdenum is (110) <111>.1,2 Figs. 1 and 2 indicate that this is, indeed, the case for direct shear at room temperature (see Ref. 3 for a description of the shear-testing equipment and procedure). Moreover, from Fig. 2, the shear stress on the (123) is lower than that on the (112). This would be the case if, as has been suggested,4,5 slip on these two planes is in reality com-

Jan 1, 1965

By AIME AIME

WIDESPREAD interest in the better utilization of coal is indicated by the attendance of over seventeen hundred men interested in the pro- cessing and utilization of coal and its by-products, at Pittsburgh, Nov. 15 to 18. The conference was truly international in scope and of a scientific character, and must be considered a real success. There were dele- gates--official and unofficial-from America, Belgium, Canada, Czechoslovakia, France, Germany, Great Britain, Japan, Mexico, and Sweden. Several Federal and 28 State departments had representatives, also many colleges and universities, and many leading industrial and mining corporations throughout the country. A feature of the sessions was that papers were mostly read in full and attentively listened to, although in some cases they were of a technical nature. The proceedings were opened by the president of Carnegie Institute of Technology, Thomas C. Baker, who spoke of the importance of the conference and felt that without foreign cooperation it could not have been held. There was no need to apologize for the movement of Carnegie Institute of Technology in the matter. Coal is commanding attention in every part of the world; so is power; and coal will remain the chief source of power for generations to come. The coal chemist is working with the engineer, and nobody can forecast what developments there will be in fuel technology. This conference may be the turning point of fuel technology in America. The development and application of these new processes may be of great benefit to Pittsburgh.

Jan 1, 1926

By S. Skowronski

The melting of cathode copper, ususally containing 95.98+ per cent. • Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulfur, however, so much sulfur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period—saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;&apos;&apos; this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulfur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulfur will ruin copper for practical purposes. The sulfur absorbed by copper during the melting period comes from two sources: (1) the sulfate left on the cathode sheets in the tank houses; (2) the fuel. The percentage of sulfates on the cathodes is variable, and depends on the care taken in washing the cathodes after removing

Jan 1, 1919

IN the footnote on the first page of Prof. Stoek&apos;s paper, as printed in vol. xxviii. of the Transactions, I alluded to him, under an erroneous impression, for which he was in no way responsible, as " the present Director of the Scranton Schools." This incorrect statement placed him in a false position, as possibly having authorized the use of a title to which he had no claim. In fact, Prof. Stoek has never had any official connec-

Jan 1, 1900

Secretary&apos;s NOTE—on page 176,of this paper, in the fourth line of the first footnote, " 4° " should, be " 1" )&apos;; and on page 180, at the beginning of line 23, (&apos;lined boot" should be " unlined boot." Discussion. Frank Owen, London, Eng. (communication to the Secretary) : In his very interesting and valuable paper, Prof. Snow

Jan 1, 1900

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;&apos;-&apos;0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

By Charles H. Fulton

IT is assumed that the word "college" for the present purpose signifies technical school or technical department of a college or university. About ten or fifteen years ago, and more recently in some instances the contact between the technical school and the industry, as represented by the operating companies, was very limited. The school made no effort to place its graduates in the industry and the graduate&apos;s first position was obtained by his own or his friends&apos; efforts; the friend often was a professor. The industries, or the operating companies, seemingly had little interest in the training of the technical graduates they employed or in seeking to discover their personal characteristics and fitness for the work. In the public mind there was little relation between technical training and industry. Such training was in the field of education; industry was in the field of business; and the interrelationship was not a matter of common knowledge or concern.

Jan 1, 1929

By John H. Hollomon

A REVIEW of the steps which have been made to increase knowledge in the field of ferrous physical metallurgy during the closing period of World War II brings both pleasure and disappointment. Contributions of great value have been made, to be sure. However, due partly to the stress of the times, researchers in this field have been in the main directing their attention toward the short-range problems involved in the development and production of materiel for war. Furthermore, publication of the results of a great number of studies has had to be delayed. Much of the German work may, indeed, be lost entirely, owing to the efficiency of our bombers, which managed to account for most of the famous Kaiser Wilhelm Institut of Dusseldorf, not to mention the other large laboratories and manufacturing plants throughout that country. It would seem safe to assume, however, that fundamental research in Germany had been forced to give way to the shallow, but more pressing, engineering problems of a country trying to avoid defeat. In Russia the picture has been clouded by the limitations imposed upon comunication; but this much does seem clear: Russia alone among the great nations of the world has maintained her long-range view and has continued to foster research of the most fundamental type. English workers; on the other hand, appear to have been able only to meet the demands of the pressing problems of war, and their studies have been of the short-range variety. That metallurgical research of any sort should have continued in France during this chaotic period in her history would seem impossible, but, amazingly, a small handful of scientists did manage to carry on their work, and it is to be hoped that more will be heard from them in the future.

Jan 1, 1946

By AIME AIME

AT a joint meeting of the Tulsa Geological Society and the Mid-Continent Section of the A; I. M. E., held at Tulsa on March 21, the history of unit development in the Kettle- man Hills field was discussed. Robert C. Patterson? Super- visor for the U. S. Geological Survey at Taft, Calif., was the speaker. An abstract of some of his remarks follows: On July 1, 1923, curtailment agreement for two years was made between the operators of North Dome Kettleman and the U. S. Department of the Interior. In this it was agreed to consider a plan of unit development, or other cooperate method of developing the structure. As a result, Kettleman North Dome Association was incorporated in December, 1930, as a non-profit cooperative corporation under the laws of California. Approved in January, 1931, by California Oil and Gas Supervisor and by Secretary of Interior. On Feb. 10, 1931, it became an active organization through election of executive officers and eleven- directors. General manager chosen. Association started to function April 1, 1931. Assumed control of 10,800 acres of proved and semi-proved land, as shown in Table 1.

Jan 1, 1932

Jan 1, 1925

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By R. W. Smith, G. W. Delamore, J. A. Spittle

RECENT work by the authors1 has demonstrated that the crystals constituting the equiaxed zone in small ingots originate, on quenching, in the chilled liquid. Whether any partial remelting2 takes place of the den-drites nucleated in the chilled region was not examined. However, the claim3 that this normally occurs, leading to crystal multiplication, has been disputed.4 Thus, for an equiaxed zone to form in the central region of an otherwise columnar ingot, it is necessary to transport crystallites from the chill zone to this region. In view of the work of Uhlmann et al.,5 it was considered desirable to examine the transport process further. Experimental Technique and Results. In the earlier experiments by the authors.1 a stainless-steel crucible 17/8 in. diam, 41/2 in. high, ad containing an alloy of A1-4 wt pct Cu, was quenched from 660°C into a bath of Wood&apos;s metal maintained at 100°C. Under these conditions a central zone of equiaxed crystals was obtained. However, if a 2250-G unidirectional magnetic field was applied for 2 sec immediately following the instant of quenching, or subsequently, the equiaxed zone did not appear. Careful thermal analysis showed that the short application of the field had virtually no effect on the thermal conditions of the melt. It thus appeared that the crystallites which were ultimately to grow large enough to form the equiaxed zone existed in the liquid immediately ahead of the interface, occlusion being prevented by the convective fluid flow induced by freezing from the walls of the cylinder. When this relative movement was prevented by the Lorenz forces induced by the application of the magnetic field, the crystallites were caught up in the rapidly advancing dendrite solid-liquid interface. To test this assumption, a small ingot of super-purity aluminum was partially melted and poured into a heated stainless-steel mold which was then immediately quenched into molten Wood&apos;s alloy. The resulting structure is shown in Fig. 1, and consists of columnar grains with a central fine-grained zone. Thus the unmelted solid present at the beginning of solidification had been transported ahead of the columnar interface. Discussion. There appears to be little or no information available on the interaction of suspended particles with a metallic solid/liquid interface. However, some information is available for transparent organic sys-

Jan 1, 1969

By Godfrey T. Vivian

Very often important discoveries are made in one industry that may be used to advantage in another, but, owing to the rarity that men step out of one industry into another, these discoveries remain unknown outside of the trade or profession in which they are made. The present paper is written solely with the object of bringing to the notice of mining and metallurgical engineers a centrifugal ore-concentrator which eventually may have a great application. Ore- Grading. Fig. 1 represents the action which takes place when solids of different dimensions are stirred up in a box and allowed to settle as minerals of the same size but of different specific gravity. This principle is applied practically in grading china-clay and in enriching tin-slimes. In the latter case the slimes are stirred around in a tub with water and allowed to settle while at the same time the side of the tub is struck with a hammer. The colloidal slimes are then poured off and various slices taken off horizontally. The great drawback of this process is that the particles are deposited horizontally and all the colloids are lost. Fig. 2 represents the action in which the particles are deposited side by side. Here the drawback is the great length of the box needed in order to prevent excessive loss. The alternative to lengthening the box is to increase the force of gravity. Centrifugal force may be regarded practically as the force of gravity augmented. Fig. 3 illustrates the Gee centrifugal machine for grading ores. The drum, A, fitted with a box, B, is mounted on a shaft or spindle, C, the whole being suspended from a ball-bearing of special design at D, supported between girders, E. Rota-

Jan 1, 1913