Search Documents

By Walter Crafts, C. M. Offenhauer

IN a previous study' of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is a more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about r1to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, 1 per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to 1-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudomartensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously' that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By C. M. Smith

PILOTED by Cadwallader, Evans, Jr., as chairman, the Coal Division got under way Monday morning for the first of three consecutive sessions. N. F. Patton started the ball rolling with a paper on the economics of anthracite distribution, which was ably discussed by H. J. Rose, W. S. Blauvelt, and others. Mr. Patton pointed out many incongruities in freight rates, dealers' margins, and other factors which are disturbing the distribution of anthracite, one result being that trucks are hauling at least six million tons of anthracite annually, half of which is stolen. In the discussion of the papers the desirability of greater uniformity in the production and shipment of coal from month to month was urged; with larger summer price concessions as a means toward this end. "Performance Expectancy of Domestic Underfeed Stokers for Anthracite," by Allen J. Johnson, brought this important platter down to date by showing the range in capacities and efficiencies to be expected from well-made stokers, and by detailing other of their operating characteristics. One of his most interesting points is that the efficiency of domestic stokers is practically equal to that of handfiring for good installations and operations of both

Jan 1, 1935

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By S. Whinery

In these times of sharp rivalry, both as to price and quality, among the makers and venders of engineering explosives, it is often desirable to be able to determine the relative energy or value of the various explosives offered for sale, in order to purchase intelligently ; or, having contracted for a large amount of an explosive of a certain standard quality, to be able to ascertain if the manufacturer keeps his product up to the specified standard. The simple and inexpensive apparatus described below was devised by the writer while engaged on the improvement of the Tennessee River, at MuscleShoals, under the direction of' Major W. R. King, U. S. Engineers, in the summer of 1879. It answered the purpose so well that it is thought that a brief account of it may be of interest to other engineers. It consisted, essentially, of an old blacksmith's anvil and a common striking hammer, such as is used for driving rock-drills. The anvil was placed face downward on solid, level ground. In what was then the top of it, a vertical hole, one and one-fourth inch in diameter and about one arid three-fourths inch deep, was made with a ratchetdrill. The surface of the anvil immediately around the drill-hole was made as true and smooth as possible with a file. Next, a new striking-hammer, weighing nine pounds, with a turned and true face, was selected ; and a handle, eleven feet long and about one and a half inches in diameter, was fitted into it so that it

Jan 1, 1886

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951

By F. R. Jones

AT Tahawus, N. Y., National Lead Co. operates the MacIntyre development. Here the world's largest titanium mine produces 5200 long tons of ore per day and pours 8000 long tons of waste rock over its dumps. Concentrated ilmenite is sent by rail to National Lead Co. pigment plants, and a second product, magnetite, is sold to steel producers in raw form or is agglomerated and shipped as sinter. Several earlier attempts had been made to produce iron from the deposits, which have been known since 1826. These attempts failed, chiefly because of titanium impurity. In 1941 the present owners reestablished the operation for production of war-scarce ilmenite, and the impurity became the main product. The Ore: The MacIntyre ore zone is about 2400 ft long and 800 ft wide in horizontal measurements. Ore outcrops were found on the northwest side of Sanford Hill, 450 ft above Sanford Lake and 2500 ft southeast. The zone dips at about 45" toward the lake and plunges to the southwest. The ore minerals, ilmenite and magnetite, are unevenly distributed in bands roughly parallel to the long axis of the ore zone and are interspersed with bands and horses of waste. Hanging wall ores are fine grained and grade from rich ore to waste rock or gabbro. Footwall ores are coarse grained and are almost entirely ilmenite and magnetite. The foot-wall waste rock, anorthosite, is the common country rock. Several faults cut the ore zone. These faults have no great displacement but do contribute to the great physical variations in ore rock and surrounding waste. The Mine: The MacIntyre mine is an open pit operation, with benches at 35-ft intervals. The lowest bench is now 54 ft below lake level. Loading equipment consists of three electric-powered shovels (a P & H model 1400 with 4-yd dipper and two Bucyrus-Erie models 85-B with 2%-yd dippers) and one diesel-powered shovel (a Northwest model 80D with 2%-yd dipper). Ore and waste are transported to a 48x60-in. jaw crusher in ten 22-ton Euclid trucks with 300-hp diesel engines. Ordinarily the two Bucyrus-Erie 2 % -yd shovels load ore into a fleet of three or four trucks. This combination works two 8-hr shifts per day, moving 5200 long tons of ore to the crusher and removing a small portion of the waste rock. The P & H model 1400 shovel, with a fleet of four trucks, loads waste on three shifts per day. The mine operates on a 5-day week, with a small maintenance crew working Saturday. Oversize rock is broken by a dropball handled by an Osgood model 825 rubber-mounted crane.' Ore and waste are broken by drilling and blasting 9-in. diam vertical holes behind the benches. Bucyrus-Erie 42-T churn drills are used to drill the holes, which are extended 4 ft below the bench level on which the broken rock will fall. Drilling and Blasting History: In its early years the mine was equipped with Bucyrus-Erie 29-T churn drills, which drilled 6-in. holes. To keep up with production requirements the hole diameter was soon increased to 9 in., and by 1950 the three 42-T drills now in use had been acquired. Early blasting experiments with different kinds and grades of explosive led to adoption of 90 pct straight gelatin dynamite as standard. It was recognized that this explosive was expensive, and from the start of operations until 1950 extensive experiments were made using blasting agents of the ammonium nitrate family. Results were recorded as uniformly poor, with great build-up of oversize rock. The expense of these experiments, and the discouraging results, caused the abandonment of any expectation of breaking MacIntyre rock with anything but 90 pct straight gelatin dynamite. Further standardization led to 9-in. well drillhole spacings set at 16 ft in ore and 18 ft in waste, exceptions being permitted only for unusual conditions. The hole burdens were theoretically about 22 ft. Due to the extreme back-slope of bench faces, caused by blasting with heavy charges of dynamite, actual burdens were commonly well over 30 ft. Lack of precise control resulted in many holes having a burden as light as 15 ft. General practice was to stem 6 or 7 ft of hole with magnetite concentrate, the amount of stemming being left to the discretion of the pit foreman. Usually all holes in a row were fired instantaneously with Primacord detonating fuse. Millisecond delays were

Jan 1, 1957

By Pradeep K. Rohatgi, Clyde M. Adams

An analysis of heal conduction in the freezing of a solution has been performed. The case considered is the semi-infinite mass of solution, bounded by a con-stant-temperature plane with one-dimensional heat flow, Numerical cooling rate and freezing rate distributions hare been calcutated for the particular case of unidirectional freezing of aqueous solutions against. a cold copper chill. The solution at each level parallel to the chill surface is subjected to a spectra of frcezing rates; the freezing rate is inilially lour., passes through a maximum, and then decreases until solidification is camplete. Arange and maximum freeeing rates are inversely proportional to the square of distance from the chill surface. The temperature of the chill surface in contact with the solution remains constant during solidification. Experimentally, it is observed that deudrite sparing increases linearly with distance from the chill surface; in the light of heat -flow analysis this means that the dendrile spacing is imersely proportional to the square root of the maximum freezing rate. SOLIDIFICATION of liquids is accompanied by rejection of latent heat at the solid-liquid interface. The over-all rate of liquid to solid transformation is governed by the rate of heat extraction. Analysis of the heat transfer in the liquid during freezing is important since it determines the freezing rate and resulting structure. A considerable amount of work has been done on metallic systems since solidification is frequently a major step in processing metals. Unidirectional freezing from heat sinks has been treated by several investigators.1-4 Much of the work has been limited to the simpler case of substances such as pure metals which freeze isothermally at a unique transformation temperature. In this case the thickness of the solid zone y, next to a chill surface. is a parabolic function of the time. 8. where a and b are constants. Eq. |1| is a close approximation giving the progress of solidification for the case in which there is a small but finite thermal contact resistance at the interface between the freezing liquid and the chill.' It has been used with some success in connection with large steel ingots4 when the therma1 contact resistance is negligibly small (as is the case when water is brought into contact with the metal chill). The constant, b. becomes zero and Eq. [l] is then exact. even when the thermal properties of the chill and the freezing liquid depend on temperature. Analysis of unidirectional solidification of solutions is more complicated since the latent heat is evolved over a range of temperatures. Next to the all-solid zone in contact with the chill surface there is a solid plus liquid zone in which solidification takes place. Although the equations presented are considered quite general the numerical and experimental results are for freezing of aqueous solutions from a copper chill. I) EXPERIMENTAL PROCEDURE Solutions of potassium chloride, sodium chloride. and lithium chloride have been used. These solutions form a eutectic: a typical phase diagram is shown in Fig. 1. A solution at its liquid us temperature is poured into a tygon tube mounted on a relatively large copper chill. The chill is immersed in a freezing mixture of dry ice and acetone at -70°C. A thermocouple connected to a high-speed recorder was mounted near the top of the chill to measure the fluctuation in the temperature of chill surface in contact with the solution. In this system the progress of solidification can be visually observed through the tygon tube. After the specimens freeze to a desired height they are removed from the copper chill and stripped from the tygon tube. Longitudinal and transverse sections are cut from the specimen for micrographic examination. Specimens in the form of a thin slice are mounted on a transparent glass slide by freezing small drops of water around the periphery. They are then polished on a series of emery papers; the final finishing is done on a soft tissue paper. A Leitz Biological microscope was used for structural observations; photography was

Jan 1, 1968

By R. G. Treuting, W. C. Ellis

D. Whitwham, M. Mouflard, and P. Lacombe (British Council Research Fellow, Labratoire du Professor Chaudron, Vitry-sur-Seine; Inqenieur de Recherches, Labratoire de Vitry; and Maitre de Recherches, Labratoire de Vitry, Professeur Adjoint de Metallurgie, Ecole des Mines, Paris)—The authors' work is of great interest in bringing out the geometrical relations existing between twinned lattices, and for the notion of a coincidence super lattice developed from this. We should like to point out that a similar idea was put forward by Friedel8 in his book on the subject of lattice merohedrism "merihedrie réticulaire:"—When two crystals A and B are twinned with respect to a mirror plane, there exists a common superlattice, "réseau periode," which is independent of the contact surface between the two crystals. The volume V of this superlattice is a simple multiple of the volume v of the lattice of crystals A, or B, (Fig. 5). This "multiple cell" is defined by the twin plane (p q r) and a row of atoms [h k l] normal to this plane, the base being taken as the smallest unit (two-dimensional) of this plane. Two cases must be considered. First when the multiple cell, as defined, has no atom site at its center nor at the center of its faces other than (p q r), v the twinning index is defined by —. In the second v case, when one of the two above conditions does not v apply, then the twinning index is V 2v A more intuitive definition of the twinning index would be the proportion of atoms of C, which would coincide with those of C1 when the C, lattice is imagined to extend on the other side of the contact surface. In the case of cubic crystals, the twinning index

Jan 1, 1952

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By C. H. Herty, J. L. Keats

In the literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete data as possible on all the factors that affect the elimination of metalloids were obtained. The Test Heat The test heat was made in a standard 100-ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y., on January 17, 1922. The Charge—Scrap.—The scrap consisted entirely of rail-heat butts, selected from a number of heats made the week before the test. The average analysis of the scrap was calculated from the analysis of these heats and from the weight of scrap from each heat. Pig Iron.—Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample. Other Materials.—Weights of dolomite, ore and spar were obtained by weighing a quantity of each just before the test and weighing the amount of each left after the heat was completed. The limestone. was weighed on the charging pans. Coal for recarburizing, ferromanganese, ferro-silicon and aluminum were weighed out as used. All these materials were carefully sampled before the test was begun. Coal consumption at the producers was obtained by getting the average capacity of the hoppers that fed the producers, and then counting the number of hoppers of coal used during the course of the heat. Products Steel.—The steel made was rolled into billets, the rolling properties being very satisfactory. The weight of steel was obtained by taking a

Jan 1, 1926

By A. H. Larson, R. J. McClincy

Laboratory-scale decopperizing experiments with multiple sulfur addifions were conducted at 330°C on ternary Pb-Cu alloys containing, as the third elenlent, Sn, Ag, As, Sb, Bi, Zn, and Au, common impurities in lead blast-furnace bullion. For silver and tin, an increased rate and extent of 'cofifier removal was obsert3ed. The elements As, Sb, Zn, Au, and Bi had no effect or less effect as compared to sulfur additions with no i)npurily additions. THE production of primary lead in the blast furnace yields an impure lead frequently containing such impurities as copper. antimony. arsenic. tin, gold, silver iron, oxygen. and sulfur. By cooling this lead to a temperature near its melting point. most of the iron, sulfur, and oxygen and part of the other impurities are removed in the form of a dross. With incipient solidification of the lead, the copper concentration wil have been reduced to 0.02 to 0.05 pct. depending upon the concentration of the other impurities. according to Davey.' Since copper interferes with the treatment of silver after the desilverizing process, it is desirable to decrease the copper content of the lead still fur-ther before the lead is desilvered. The decopperizing of the lead is accomplished by stirring a small quantity. approximately 0.1 pct. of elemental sulfur into the lead at a temperature near its melting point, 330" to 360°C. The copper is removed as a copper sulfide which constitutes a small fraction of a voluminous dross consisting mostly of lead sulfide and entrained metallic lead. The residual copper concentration following the decopperizing operation is frequently as low as 0.001 to 0.005 pct. Thi fact has aroused considerable interest because the equilibrium copper concentration of lead in contact with solid PbS and solid Cu2S is at least an order of magnitude greater, 0.05 pct Cu at 330C. 1, 2 Most investigators have suggested that various impurities in the lead bullion are responsible for the very low copper concentrations frequently encountered in practice. There is little agreement, however? as to which of the impurities are helpful and which are not.3"11 Also. few investigators have sought to explain the mechanisms responsible for the removal of copper to very low concentrations. Willis and Blanks9 have proposed that a nonstoichiometric copper-deficient cuprous sulfide forms in place of the supposed Cu2S. Being copper-deficient, this sulfide phase would possess a low copper activity, and the diffusion of copper dissolved in the liquid lead into this phase would be greatly facilitated. Pin and wagner2 have investigated the removal of copper from liquid lead by studying the effect of impurity-doped lead sulfide on the decopperizing of pure Pb-Cu alloys. Samples of the doped PbS were held in contact with copper-saturated lead for 1 week at 33'7°C. They reported a beneficial effect on decopperizing with bismuth and antimony and no effect with tin or silver. which is directly opposite to the results observed in practice and those reported by Davey 3 and this studv. The purpose of this paper is to describe the effects of certain additive elements on the extent to which copper can be removed fro111 liquid lead by successive additions of sulfur. The impurity elements were added individually to prepared Pb-Cu alloys. The resulting ternary alloys as well as a binary Pb-Cu alloy were then decopperized with repeated additions of sulfur. EXPERIMENTAL Materials. Granulated test lead with a purity of 99.999 pct and the additive elements Cu. Ag. Sb. Bi. Zn. Sn. and Au with purities of 99.99 pct were American Smelting and Refining Co. research-grade materials. The major impurities in the lead were 1 ppm each of iron and copper. all others being less than 1 ppm. The arsenic used was a technical-grade arsenic of 98+ pct purity. Reagent-grade flowers of sulfur were melted under argon to provide small pieces free of fines. Apparatus. The decopperizing experiments were carried out in a 25-mm-OD by 375-mm-long Pyrex tube sealed at one end. The tube was mounted vertically in a resistance-heated. hinge-type tube furnace controlled to within ±lcC. Temperature measurement was accomplished by means of a standardized chromel-alumel thermocouple sealed into the base of a silica. paddle-type stirring rod. All decopperizing experiments were carried out under an argon atmosphere. Procedure. A Pb-Cu starting alloy containing 0.05 pet Cu was prepared under carbon and poured into cold tap water to produce shot. The ternary alloys were prepared by melting together 100 g of the starting alloy and a sufficient amount of the impurity element to yield the desired concentration. The resulting alloy was then homogenized in a Pyrex tube at 450C with continuous stirring. The furnace temperature was then lowered to the operating temperature of 330°C. When thermal equilibrium had been obtained at the operating temperature, individual additions of 0.2 pct (0.2 g) of solid sulfur were added to the melt and stirred in. Stirring was continued for a period of 3 min. discontinued for 5 min. and resumed for the remaining 2 min of a 10-min cycle. This cycle was repeated for as many sulfur additions as desired. When the decopperizing experiment had been completed the lead bullion was quenched and samples of the bullion and dross phases were taken for analysis. Results. The results obtained in the decopperizing

Jan 1, 1970

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By Blamey Stevens

(San Francisco Meeting, October, 1911.) My previous paper is entitled, The Laws of Igneous Emanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical conditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming, from those parts of the intrusion which have solidified below the lower level.

Apr 1, 1912

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists' Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention' to this subject had been crystallized by a symposium held by the Faraday Society in 1925. ' After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country... . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on `Basic Open Hearth Steelmaking'." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circumstances which led to the publication of "Basic Open Hearth Steelmaking" in the spring of 1944. The book consisted of nineteen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, B. M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1951

By C. Schlumberger, M. Schlumberger

The object of this paper is to clarify the idea, so important when exploring by potential methods, of the depth of investigation attainable by electrical measurements. After defining, with some precision, .the term "depth of investigation'' in geophysics, the authors show how it is possible to regulate this depth in potential methods and to obtain an 'electrical drilling" from surface observations. They consider also the difficulties encountered in deep measurements and indicate how it is possible to reach greater depths than those having an industrial interest. Depth of Investigation The term, depth of investigation, in its general sense, is easily understood. For instance, a driller who can pull cores from a depth of 2000 m. is capable of working, with accuracy, to that depth. By means of a properly placed drill, he may locate an orebody at a depth of 1999 m., however small this orebody may be. On the contrary, the term as used in geophysics requires precise elaboration. As a matter of fact, no geophysical method, irrespective of the physical property studied (density, magnetic permeability, conductivity), can discover a very small body at a great depth because, in practice, the physical parameter upon which such a geophysical method is based is never regular enough, throughout the ground, to distinguish the feeble anomaly caused by the small, deep-lying body from the numerous anomalies due to irregularities of the encasing terrains. Aside from this question of the ratio between the size of the body being hunted for and its depth of burial, a second factor plays its role in the possible depth of investigation; that is the difference, for the parameter under consideration, between the body and its surrounding material. The greater this difference, and the more homogeneous the encasing terrains, the greater is the possible depth of investigation. This being generally established for all geophysical methods, it is possible to distinguish two main classes of these methods, from this same point of view

Jan 1, 1932

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957

By David Browne

THE use of coal-dust fired reverberatory furnaces, or indeed of reverberatory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem, was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved.

Jan 1, 1915