Search Documents

Jan 1, 1969

By George W. Neumann

The mines and concentrator of Brunswick Mining and Smelting Corporation are located in the northern part of the province of New Brunswick, approximately 20 miles distant from the City of Bathurst. Discovery of the No. 6 orebody by diamond drilling in 1952 was followed by the finding in March 1953, of the larger and higher- grade No. 12 orebody, approximately six miles to the north of the No. 6 deposit. Original development was financed by St. Joseph Lead Co., and included a small open-pit operation with a 10C ton per day pilot mill at No. 6 orebody, shaft sinking and underground development at No. 1; orebody, and an extensive program of laboratory and pilot plant metallurgical research on No. 12 ore. These operations were suspended in May 1958, and remained in standby condition until June 1961, when the equity of St. Joseph Lead Co. was purchased by a group headed by M. J. Boylen, K. C. Irving, Maritime Mining Corporation, and the Patino Corporation. Construction of a mine plant and concentrator at the No. 12 mine commenced in October 1962 and the concentrator was placed in operation in March, 1961b. Preparation of the open pit mine for production, construction of the No. 6 Concentrator to produce bulk Pb-Zn-Cu-Ag concentrate from No. 6 ore, and construction of an Imperial Smelting Process smelter at Belledune were started in 1964 and placed in operation in September 1966.

Jan 1, 1970

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"' the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,' and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,' or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By Bernard MacDonald

Of the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the cluantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted, the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide,plant than that of being economical and corlvellient containers or receptacles for holding the pulp, solutiou, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to dolids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge; that is, each solid particle of the pulp, whether it be of' 180- or 400-mesh size, should be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertaiued to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Jan 1, 1912

By Richard W. Smith

KYANITE, long known to occur in Georgia, did not excite commercial interest until about 1930. Investigations revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumula-tion from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not' more than a few feet. The larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersham County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habersham County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanite-mica schist belt in Habersham and Rabun counties will be discussed in this paper.

Jan 1, 1936

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,' Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill'o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

By Rudolph G. Wuerker

MUCH descriptive matter[ ] has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The wide- spread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation.

Jan 6, 1953

By J. A. Jr. Church

I. EARLY FURNACES. COPPER blast-furnace construction in America has long recognized a general standard in the rectangular mater jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few mouths by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By Sweetser, Ralph A

AT the fall meeting of the Iron and Steel Division, Oct. 4, 1934, in New York, a symposium was held on Slag Control in the Making of Iron and Steel. The chairman was J. H. Nead and the vice chairman, G. B. Waterhouse. The latter presided at both morning and afternoon sessions. The papers and discussions were presented in the order in which they appear on the following pages. To meet space requirements, much of this material has been considerably condensed. CONTENTS Slag Control and the Blast Furnace. By Ralph H. Sweetser. (With dis¬ cussion.) I Slag Control in Rimming Steel. By L. F. Reinartz 5 Slag Control Applied to Low-carbon Steel. By Frank G. Norris 9 Discussion on both papers 11 Slag Control for Basic Open-hearth High-carbon Steel. By W. J. Reagan. (With discussion.) 14 Slag Control for Recarburized Rail Steel. By A. P. Miller and T. S. Washburn. (With discussion.) 18 Slag Control for Alloy Forging Steel. By A. L. Feild. (With discussion.). . . 24 Slag Control for Alloy Forging Steel. By R. C. Good 27 Slag Control in Acid Open-hearth Steel. By Francis B. Foley. (With dis¬cussion.) 29 Slag Control for Basic Electric-furnace Steel. By H. F. Walther. (With discussion.) 31 Physical Testing of Slag. By A. B. Kinzel. . 40 General Discussion 41

Jan 1, 1935

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal.

Jan 1, 1943

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894

Jan 1, 1913

By Charles L. Mantell, Kurt Straler

The hydrogen reduction of Cr2O3 to chromium metal was found to be feasible at very low water-vapor concentrations, corresponding to dew points of -38° to -24°C, over a temperature range of 1130" to 1490°C. Hydrogen reduction under these conditions was predicted by the calculated equilibrium curves which also indicated that CrzOs is reduced directly to chromium without forming the intermediate oxide, CrO. This reduction path was confirmed by X-ray diffraction analysis. The percent reduction of Cr2O3 at each reaction temperature was constant with time, suggesting an inhibiting effect of water vapor. A small increase in the residual water-vapor concentration of a single temperature, 1490°C, strongly retarded the rate of reduction This effect was expressed by an empim'cal equation which indicated a direct relationship between "distance from equilibrium" and the rate of reduction. me effect of temperature over the range of 1130" to 1490°C was expressed in an Arvhenius plot of log rate vs reciprocal absolute temperature. From this curve the apparent enthalpy of activation was found to be 29,600 cal. Based on the hypothesis that the rate of reductiun is contvolled at the oxide-metal interface, an over-all rate equation consistent with the experimental data and the thery of absolute reaction rates was formulated. A simplification of this expression to an Arrhenius equation was justified by the overriding effect of temperature on the rate of reaction for the minimum water-vapor concentration range. MOST of the metals in Subgroup V1 of the periodic table can be prepared commercially by direct reduction of their oxides by hydrogen or carbon monoxide, at temperatures considerably below the melting points of both the metals and their oxides. Chromium is an exception, being generally reduced from its ore, Cr2O3 . FeO, by silicon in an electric arc furnace which operates above the melting point of the Fe-Cr alloy or above the melting point of chro- mium if a chromium oxide be the starting material. In reduction of chromium oxide by hydrogen, either reduction does not occur at all or the rate of reduction is extremely slow. Theoretical considerations based on the high, exothermic, free energy of formation of Cr2O3 compared to the oxides of the other Subgroup VI metals, molybdenum, tungsten, and uranium, would also suggest a slow rate of reaction and a high activation energy. Interest in the direct gaseous reduction of fine-powdered ores in fluidized beds was considered justification for examination of this reaction. In order to develop a basis for a continuing study of the commercial feasibility of the direct gaseous reduction of chromite, a study of the kinetics of the reduction of Cr2O3 with hydrogen was undertaken. To the authors' knowledge no accurate kinetic data for this reaction have been obtained. Neither has an activation energy been determined nor has an attempt been made to establish a mechanism of reaction. LITERATURE Maier10 compared the data of I. Y. Granaat,6 H. von Wartenburg and S. Aoyama, and G. Grube and M. Flad7 with that derived from calorimetric and ther-modynamic properties for the equilibria for the reduction of Cr2O3 with hydrogen. These results, plotted as the log of the equilibrium constant vs absolute temperature for the reduction of Cr2O3 and the intermediate oxide, CrO, to chromium, show agreement between the differently derived data. In both cases the equilibrium constants were extremely low. Maier showed that, over a temperature range of 1000° to 2000°K, Cr2O3 is more readily reducible than CrO. Granat assumed that CrO was preferentially formed from Cr2o3 above 1100°C. Grube and Flad's analysis of their reaction products in the 895" to 1000°C range indicated the coexistence of only Cr2O3 and chromium. The hydrogen reduction of the other Subgroup VI metals, molybdenum, tungsten, and uranium, shows that reduction of the higher oxide proceeds through all of the intermediate oxides before being reduced to the metal. Since evidence pointed to an anomaly in the reduction behavior of Cr2O3, the authors investigated the reduction path of Cr2Os.to chromium. This was done theoretically with more recently available free-energy data and experimentally by X-ray diffraction analysis. This work reinforces Maier's conclusion.

Jan 1, 1964

By C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble copper from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976