Search Documents

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By Jose F. Agapito

This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator; The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver. Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River formation at a depth of 600 to 850 ft. Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek. The distance from the mine to the side of the mountain varies from 500 to 1200 ft, and its height above the stream floor is approximately 700 ft.

Jan 5, 1974

By Ikuya Takase

INTRODUCTION Since the occurrence of the first oil crisis, coun-tries of the world, especially oil-importing countries have made sustained and vigorous efforts to lessen the dependency on oil as a source of energy supply. The adoption of "Principles of Coal Policy" by the IEA Ministerial Governing Board Meeting in May, 1979 was the first formal action taken by major energy consuming countries. At the Venice Summit in June, 1980, it was agreed that production and use of coal should be doubled over the next ten years. In fact, the world coal use in 1980 showed around a 10 percent increase over the previous year. Recently, we have seen an indication that the balance of oil supply and demand in the short term have eased. But I believe that it remains vital that we continue to encourage the development and introduction of alternative energy sources. Because, from the medium and long range viewpoint the recovery of the worldwide economy will lead us to increased oil requirements and thus we will be faced with the cyclical, structural tightening situation between the supply and demand of oil. Moreover, we are still convinced that the constraint of the supply capabilities of the Middle-East nations may be increasing in the long-term, since there still remains political uncertainties among these nations. Consequently, above all, coal is viewed as an alternative energy resource available for immediate expansion of use and is given as high a priority as nuclear power. In Japan, we regard coal as the most reliable alternative energy resource to replace oil. According to the "Alternative Energy Supply Targets" approved by the Cabinet in November, 1980, the level of coal imports is estimated to approximately double by 1990, while our domestic coal production will remain nearly at the same level. The transition from oil to coal is found in the recent import levels of coal---73 mil¬lion tons in 1980, a 23 percent increase over the 59 million tons imported in 1979. There was an upsurge in steaming coal imports, reflecting the transition in feedstocks---7.2 million tons in 1980, four times over the previous year's amount. Henceforth, from the medium to long range view, the demand for coal, especially that of steaming coal is forecast to continue to grow. The timely expansion of supply capabilities is our utmost concern and should be one of the most significant goals of our comprehensive policy. The Overseas Coal Investigative Committee, a privately organized advisory panel to the Director-General of the Natural Resources and Energy Agency of the Ministry of International Trade and Industry (MITI), investigated means to secure a stable supply of overseas coal. The panel presented its interim proposals in August, 1981, recommending the diversification of coal import sources, extensive use of low rank coal, as well as enhanced international cooperation between coal producing and importing countries. THE CONTENTS OF THE COMMITTEE'S REPORT Four Points for Major Consideration In order to ensure a stable supply of overseas coal, Japan needs adequate policy measures consistent with the characteristics of coal resources and environmental requirements, giving consideration to Japan's status and the role she is expected to play in the areas. From the above, great importance should be attached to the following four points: All the components of the "Coal Chain" (Namely, the development of mine sites, construction of railroads, port loading facilities, coal shipping vessels, port receiving facilities, including coal centers and international transport facilities etc.) should be reviewed and reformed with steps taken to assure efficiency consistent with the entire coal chain system. The complete formation of a coal chain system requires such lengthy lead times and huge amounts of investment that necessary measures should be undertaken well in advance utilizing long-range projections of future demands and various economic surveys. Policy planning should be conducted taking into account of harmonizing stability and economics of the supply structure. For ensuring the long-term stability and expansion of the coal trade, international cooperation on a bilateral and multi-national basis should be encouraged. Mutual understanding and close relationships are essential to facilitate the formation of the supply system and to promote the extensive use of coal. Direction and Problems Related to Supply Stability Expansion of Supply Capabilities. World coal imports in 1979 amounted to 229 million tons, of which Japan's share amounted to 59 million tons, or one fourth of the entire amount. The imports of European and Asian countries accounted for 83 million tons and 7 million tons respectively. According to the examination of the Investigative Committee, Japan's coal requirement is estimated to be between 140-150 million tons by 1990, nearly the same level as announced in the Provisional Long-Term Energy Supply and Demand Outlook in 1979. This fore¬cast is-to be revised in April, 1982. Japan's demand is expected to be met through fiscal 1985; however, by 1990, the supply is estimated to fall short of demand, particulary, in the field of steaming coal. For the expansion of supply capability, first, mine development should be accelerated. The proposed

Jan 1, 1982

By L. D. Frink

Those actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be done in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which permits it to be put up or taken down in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

By W. Weissberger, Frankiewicz, L. Pommier

Introduction In the U.S., about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacing these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal in unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still have a long way to go and costs are very high. Another option, which appears very attractive, is the use of solid coal in a liquid fuel form - coal slurry fuels. Occidental Research Corp. has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC), a wholly-owned subsidiary. Both coal-oil mixtures and coalwater mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality metallurgical coals. There are a number of incentives for potential users of coal slurry fuels and in particular for coal-water mixtures (CWMs). First, CWM represents an assured supply of fuel at a price predictable into future years. Second, CWM is available in the near term; there are no substantial advances in technology needed to provide coal slurry fuels commercially. Third, there is minimal new equipment required to accommodate CWM in the end-user's facility. Fourth, CWM is nearly as convenient to handle, store, and combust as is fuel oil. Several variants of CWM technology could be developed for different end-users in the future. One concept is to formulate slurry at the mine mouth in association with an integrated beneficiation process. This slurry fuel may be delivered to the end-user by any number of known conveyances such as barge, tank truck, and rail. Slurry fuel would then be stored on-site and used on demand in utility boilers, industrial boilers, and potentially for process heat needs or residential and commercial heating. An alternative approach is to formulate a low viscosity pre-slurry at the mine mouth and to pipeline it for a considerable distance, finishing up slurry formulation near the end-user's plant. Finally, at the other extreme of manufacturing alternatives, washed coal would be shipped to a CWM manufacturing plant just outside the end-user's gate. Depending on fuel specifications and locations of the mine and end-user facility, any of these alternatives may make economic sense. They are all achievable in the near term using existing technology or variants thereof. The Coal-Water Mixture CWMs contain a nominal 70 wt. % coal ground somewhat finer than the standard pulverized ("utility grind") coal grind suspended in water; a complex chemical additive system gives the desired CWM properties, making the suspension pumpable and preventing sedimentation and hardening over time. Figure 1 shows the difference between a sample of pulverized coal containing 30 wt. % moisture and a CWM of identical coal/water ratio. The coal sample behaves like sticky coal, while the CWM flows readily. The combustion energy of a CWM is 96-97% of that associated with the coal present, due to the penalty for vaporizing water in the CWM. Potentially any coal can be incorporated in the CWM, depending on the combustion performance required and the allowable cost. CWMs are usually formulated using high quality steam coals containing around 6% ash, 34% volatile matter, 0.8% sulfur, 1500°C (2730°F) initial deformation temperatures, and energy content of 25 GJ/t (21.5 million Btu per st). Additional beneficiation to the 3% ash level can be accomplished in an integrated process. There are a number of minimum requirements which a satisfactory CWM must meet: pumpability, stability, combustibility, and affordability. In addition, a CWM should be: resistant to extended shear, generally applicable to a wide variety of coals, forgiving/flexible, and compatible with the least expensive processing. It was found that a complex chemical additive package and control of particle size distribution are necessary to achieve these attributes simultaneously, while maximizing coal content in the slurry fuel. Formulation of Coal-Water Mixtures A major consideration in the manufacture, transportation, and utilization of a slurry fuel is its pumpability, or effective viscosity. Most CWM formulations are nonNewtonian, i.e., viscosity depends on the rate and/or duration of shear applied. Viscosities reported in this paper were obtained using a Brookfield viscometer fitted with a T-spindel and rotated at 30 rev/min, thus they are apparent viscosities measured at a shear rate of approximately 10 sec-1. The instrument does reproducibly generate a shear field if spindle size and rotation rate are held fixed. By observing the apparent viscosities of several slurries at fixed conditions it is possible to obtain a relative measure of their viscosities for comparison purposes. A true shear stress-shear rate relationship at the shear rates at which the CWM will be subjected in industry may be obtained using the Haake type and a capillary viscometer. These viscometers are used for specific applications. However, for comparison purposes, apparent viscosities are reported.

Jan 1, 1985

By S. F. Frederick, G. F. Pittinato

The deformation mechanisms operating in Ti-5Al-2.5Sn at 20°K under uniaxial and biaxial stress fields were determined by using both optical and electron microscopy. In the uniaxially stressed specimens, de-fu~rnation twins were found only in the immediate vicinity of the fracture. Twinning was, however, established as a deformation mechanism under biaxial stress conditions. The same slip systems were opera-tiz,e under both uniaxial and biaxial stress. Prismatic slip was identified as the major slip syslem; however, basal and first-order pyramidal slip also occurred, but to a lesser degree. The interaction of moving dis-locations on intersecting slip planes resulted in the formation of jogs and dipoles. Hexagonal dislocation networks were formed only under biaxial stress conditions. A discussion is given on the formation of hexagonal dislocation networks. IT has been shown that titanium alloys can exhibit unusually high strengths when tested in a biaxial stress field.'-" The high biaxial strengths are a consequence of a strong basal plane sheet texture which results in distinctly anisotropic flow properties. This texture strengthening appears to decrease with decreasing temperature2 and would seem to indicate a change in deformation modes. For example, in a uniaxial tensile test, Ti-5A1-2.5Sn yields isotropically at 20°K but is strongly anisotropic at room temperature. The increase in biaxial ultimate over uniaxial strength at 20°K is also much less than at room temperature. It is known that titanium car] form deformation twins more readily at cryogenic temperatures than at room temperature.4 Since the formation of deformation twins will reduce the degree of basal texture in sheet material,' an accompanying decrease in texture strengthening would be expected. To investigate more fully the nature of texture strengthening at cryogenic temperatures, the deformation modes of Ti-5A1-2.5Sn tested in uniaxial and 1:1 biaxial tension at 20°K were studied by optical and electron transmission microscopy. EXPERIMENTAL PROCEDURE The uniaxial and biaxial stress test specimens were prepared from 0.020-in. thick sheets of Ti-5A1-2.5Sn ELI having the composition shown in Table I. Uniaxial stress conditions were obtained by using flat tensile specimens machined from the sheet material. The longitudinal axis of the tensile specimens was aligned perpendicular to the rolling direction of the sheet. Tile biaxial test specimens were prepared by rolling precut, 19-in.-lengths of sheet into 4-in.-diam cyl- inders. Following longitudinal butt welding, the cylinders were stress relieved at 1000°F for 4 hr. A 9-in. sq "window" was then chemically milled into each cylinder's surface reducing the wall thickness in the milled area to approximately 0.006 in. The testing procedure consisted of pressurizing the cylinders while simultaneously applying a tensile load. Using this technique, a 1:l axial to hoop stress was obtained. Complete details of the specimen and testing procedures are given in Refs. 1 and 2. The biaxial and uniaxial stress specimens were all tested in liquid hydrogen. Specimens for electron transmission microscopy were prepared by first chemically milling to a thickness of about 0.001 in. followed by electrolytic polishing to electron transmission thickness. The chemical milling solution, consisting of 800 ml of water,

Jan 1, 1970

By Walter E. Mingramm

The construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquefied air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the difficulty and cost of keeping on hand a large quantity of liquefied air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found

Jan 1, 1909

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

By Bezalel C. Haimson

Anna, Ohio, at the junction of Cincinnati, Findlay and Kankakee arches, has been the site of repeated and sometimes damaging earthquakes. As part of a seismicity investigation near-surface (0.15-1 m depth) overcoring strain measurements were conducted in four limestone and dolomite quarries surrounding Anna, the results of which suggest a complicated regional stress pattern, with changes in the maximum horizontal stress direction from N45ºE to N15ºW. Since such abrupt stress fluctuations are rather atypical in the Midwest and since the reliability of near-surface tests in defining regional stress had not been established, we decided to remeasure the stresses at the same locations but at greater depths (0-200 m) using the hydrofracturing method. Owing to the weak horizontal bedding planes of the Silurian shaly limestones and shaly dolomites and the relatively shallow depths, many of the tests yielded horizontal fractures, providing information only on the vertical principal stress (-0.029 MPa/m depth). However, sufficient tests in each of three testholes resulted in vertical hydrofractures to enable the calculation of all three principal stresses. Within 50-170 m depth the horizontal stresses in all three quarries appear to belong to a uniform regional Stress field defined by the following relations: [']Hmin = 5.1 + 0.014 D; [0] Hmax = 10.1 + 0.014 D, where D is depth in meters. The direction of [O]Hmax within 50-170 m depth is uniform at N70°E (±15º). The hydro- fracturing results obtained at Anna, Ohio are in agreement with the prevailing stress regime in the midcontinent both with respect to magnitudes and directions. The results suggest a possible thrust mechanism for a proposed NW-SE fault along which most of the earthquake epicenters have been located, and a left lateral strike-slip at greater depths. The focal mechanism solution of a recent major earthquake near Sharpsburg, Kentucky, some 200 km south of Anna, also indicates strike-

Jan 1, 1982

Edward Keller, Baltimore, Md. (communication to the Secretary): When, at the New Pork meeting, February, 1899, Mr. Douglas gave an abstract of his highly interesting paper on the Copper Queen mine, he invited the members of the Institute, in his usual progressive spirit, to make a full scientific investigation of the region of that mine during the prospective excursion to Bisbee, Arizona. I volunteered to examine some of the metallurgical processes and products of the works, and obtained from Mr. Douglas a valuable series of samples. Upon the issue of his paper, however, I found that he had already a considerable volume of analyses of those products, and that little was left for me to do in that respect, except to duplicate his results, the importance of which work would not have been commensurate to the time and labor involved. I selected, therefore, only some points which he had not made entirely clear, or concerning which I was skeptical. The details of most of my work will appear in a future paper. From Mr. Douglas's figures I have calculated the values for the elimination of impurities in the so-called Leghorn converter, introduced by him at the Copper Queen works, and have found them to be as follows: Percentage of Elimination of Impurities in Pour Blows of a Converter. No of ' Selenium Sulph'r Iron. Zinc. I Nickel. Lead. Antimony Arsenic. and Blow- ! Tellurium .. 1.......... 99.4 99.6 88.0 92.6 94.4 81.6 83.8 40.3 2.......... 99.0 99.6 98.1 92.5 96.8 71.9 76.6 38.1 3.......... 98.8 99.5 93.5 91.4 96.3 63.8 80.6 25.3 4.......... 99.8 99.5 95.8 95.8 97.5 65.3 76.9 36.3 Average 99.2 99.6 93.8 93.1 . 96.2 70.6 ! 79.5 35.0

Jan 1, 1900

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4'5 dense patches or clusters of prismatic dislocation loops, planar arrays,4'10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10' life level the

Jan 1, 1969

These springs arc situated on the south bank of the river about four miles below the City of Great Falls. In addition to the spring on the bank there are several in the bed of the river. Estimates on the flow of all these vary from 350 to 600 cubic feet per second, and as the temperature is practically constant at 53° F. throughout the year, the effect on the river water is to prevent the formation of anchor ice at the Rainbow Fails power development below, trouble of this source being in evidence every winter at the Black Eagle Falls above. Geologists claim that the water of the Giant Springs is derived from seepage through an old pre-glacial channel of the Missouri River now occupied by Sand Coulee, five miles up-stream from Great Falls. The water in this buried channel seeps through the flat-lying sandstone of the region and again unites with the present stream at the site of the springs.

Jan 1, 1913

By C. R. Fettke

In 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northwest of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and LUX. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J. Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey. Stratigraphic Position of the Producing Sand The producing sand at Hamilton Corners is encountered at depths of from 364 to 560 ft., depending on the location of the well and the topog-

Jan 1, 1928

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.&apos; In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.&apos; The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By O. P. Dolph

SPANIARDS were probably the first to mine the rich surface ore in the veins cutting the rhyolite capping that outcrops on the hills of La Mazata, oil the Allyones side of the Magdalena valley in Jalisco, Mexico, although the name comes from a word of Indian origin meaning "deer". The camp is about 12 km. west of Magdalena, a town on the Southern Pacific Railroad, and about 17 km. north of Etzatlán, on the Mexican National Railroad, at an elevation of 4500 ft. The climate is subtropical with no extremes of heat or cold, the rainy season beginning in June and ending in October.

Jan 1, 1938

By Eric Kula, Åke Josefsson

L. J. Dijkstra and R. Sladek, (Ontario Research Foundation, Toronto, and Institute for the Study of Metals, Chicago, respectively)—This interesting paper confirms some results obtained some years ago in collaboration with Fast: namely the broadening of the nitrogen peak by the presence of small amounts of manganese. Later on a more extensive study of this effect was made at the Institute for the Study of Metals at Chicago. As the work has not yet been submitted for publication we wish to mention here briefly some of the results. The effect of about 0.5 atomic pct manganese, chromium, molybdenum, or vanadium on the nitrogen-peak in iron was examined. The broadening found previously in the case of manganese was even found to be more pronounced for chromium. In the case of molybdenum and vanadium a double peak was observed which seemed to justify the idea that in all cases mainly two relaxation times were involved: namely, the normal relaxation time as found in pure iron and a second relaxation time related to the existence of abnormal interstitial lattice sites introduced by the foreign metallic element. The analysis showed that for the normal nitrogen-peak as a reference at 22°C the abnormal peak was found at about 32°, 47°, 75°, and 87°C in the case of manganese, chromium, molybdenum, and vanadium, respestively. In the manganese alloy the free energy difference for a nitrogen-atom at an abnormal and a normal lattice site was estimated at 2800 cal per mol. This means that for temperatures above 100°C the solid solubility and overall diffusion rate of nitrogen is not much affected by additions of 0.5 pct Mn. We believe that the difference in rate of precipitation of nitrogen in pure iron and the manganese alloy is mainly a question of the number of potential nuclei available in the different steels. In studying the effect of these alloying elements on precipitation of nitrogen, a distinction must be made between the para reaction and ortho reaction, using terminology introduced by Hultgren.7 The ortho reaction in which the alloying metallic element participates in the diffusion under formation of nitrides occurs at high temperatures such as 600°C. The para reaction in which the alloying metallic element does not diffuse and in which the nitride inherits its alloy content from the matrix occurs at lower temperatures. To prevent the ortho reaction the alloys have to be quenched rapidly from the phase. It is not surprising that the authors find that the height of the peak indicates a lower nitrogen content than chemical analysis. In the first place the peak is not a single relaxation peak and secondly, the steels were not quenched from the phase after the nitrogen was introduced at 580 °C.

Jan 1, 1953