Search Documents

By P. D. I. Honeyman, P. A. Faust

At the Miami plant of the International Smelting Co., Inspiration, Ariz., there are four reverberatory furnaces, all 120 ft. long. At present only one of these furnaces is in operation. It is operated as a wet-charge furnace, the charge being distributed for about 65 ft. down the furnace length. Usually this charge contains about 12 per cent moisture and runs 25 per cent sulfur, of which there is eliminated in the furnace from 25 to 30 per cent. The furnace is oil-fired, the fuel being burned in a battery of Cananea-type, low-pressure burners. The flame is kept short and conditions so adjusted as to obtain complete combustion within the furnace. The average furnace draft, taken through the verb arch, amounts to only 0.02 in. of H2O. Draft is purposely kept low to cut down infiltration through the flues and boiler settings, and control dampers are regulated to maintain this uniform condition throughout the charging as well as the smelting period. Hot gases discharge from the furnace uptake through a common header flue to the waste-heat boilers. The general layout and dimensions of the plant are shown in Fig. 1. Four Stirling boilers, two of class M-26 (713 hp.) and two class M-31 (850 hp.), serve the furnace. Three usually are sufficient to take care of normal operation, the fourth boiler being used as a spare when necessary. The distribution of hot gases to the various boilers is regulated by the dampers in the boiler exit flues. Normally the boilers closest to the furnace uptake would evaporate more water than do those farther away, but dampers are regulated so as to distribute fairly well the load between the several boilers. Steam from the waste-heat plant is delivered to the adjoining power house of the Inspiration company, where it is used both in the Nordberg blowing engines and for electrical generation. Steam pressures and temperatures recorded are those in the main power-plant header and are thus inclusive of all losses in about 500 ft. of 10-in. line. Steam for smelter heating and auxiliary use is taken from the main waste-heat header, is reduced to 125 lb. and distributed through separate lines. Boiler feed water is supplied by the power plant and consists of returned condensate, augmented to a large extent by make-up water

Jan 1, 1934

By A. S. Callen

These iron mines of Spain are located on the mountain ridge forming the boundary between the Teruel and Guadalajara provinces, called Sierra Menera. They form a property of 25 mines extending over an area of 1,677 hectares (4,140 acres) situated at a height varying from 1,200 m. (3,940 ft.) to 1,500 m. (4,920 ft.) above sea level. The deposit follows the direction north to south; huge masses of ore are being found both on the slopes and at the summit of the Sierra. The ore occurs among quartzites and magnesite limestone, in some places overlaid by quartzite 15 m. (50 ft.) thick; in some others (and this is more general) the ore is overlaid by earth and boulders of quartzite origin; this layer is about 8 m. (26 ft.) thick. The ore beds occupy the geological horizon of the Superior Trias or Muschelkask, which are here in direct contact with the Silurian quartzites. The lime-stones have been more or less transformed. There is ample evidence to show that these mines were worked in very ancient times—objects and tools employed in mining by the ancient Romans and Arabs are to be found plentifully in old workinigs which extend down into the deposits. It has been estimated that more than 10,000,000 tons of ore were mined in the old days in this district and carried to the primitive forges in the vicinity where iron of much renown in Spain was extracted. Remains of more than 20 of these forges are found in the neighborhood of Sierra Menera and are usually situated near waterfalls and forests. Much investigation has been carried on for the purpose of determining the quantity of ore to be found in these mines, but no exact calculations can be made at present. When the investigation is completed it will surely be found that the deposit contains a much larger quantity than the 100,000,000 tons indicated by the present workings. The mines are now worked as open quarries and this method can and will be followed for a long time, probably until the deposit is worked out. Figs. 1 and 2 give some idea of the quarries in operation and the reserves, the iron-ore stocks, screening installation and general arrangement. From these quarries 1,000,000 tons can be mined annually (987,000

Jan 1, 1916

By E. J. MCOAUSTLAND

THE behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The "tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32° F. is not so well known. Tests made by Prof E. G. Coker, at McGill University,' show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of sortie investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

May 1, 1906

By B. Chalmers, S. Wojciechowski

THE structure of the equiaxed zone of several A1-Cu samples mechanically stirred during unidirectional solidification was examined. The stirring was produced by rotary oscillation of the mold about its vertical axis.' It was found that in Some samples the structure is not of the same type over the whole of the equiaxed zone; it consists of regions with two different etching responses. Fig. 1 shows this structure in a Al-1 wt pct ku sample. The lighter etching regions with a coarse structure form something like a network and the darker etching regions with a finer structure can be observed as the continuation of the coarse structure inside this network. The difference in size and shape of the dendrite branches (they are rounded in the coarser structure) is similar to that found by Williamson and Chalmers in ice crystals solidified in undercooled water: when the amount of undercooling was small, the ice crystals were more rounded and coarser than these solidified with a larger amount of undercooling.' It seems justified to conclude that the observed structure resulted from solidification under different thermal conditions: the coarser structure solidified first out of the "purer" liquid and with a smaller amount of undercooling and the finer was formed later out of solute-enriched liquid under conditions of much more rapid heat extraction. A considerable change in the heat flow conditions at the later stages of solidification can be easily understood by taking into account that the coarser crystals form a continuous network and the amount of trapped liquid is relatively small; hence the contribution of latent heat is much smaller in the later stages of solidification. The difference in structure and etching characteristic reflects a difference in composition between these two regions. It was found that the darker etching re- gions are harder (30.4 to 31.3 HV5) than the lighter etching ones (25 to 26 HV5). A similar type of structure was found in a A1-4 wt pct Cu sample grown by Czochralski method. Fig. 2 shows the structure in the lower part of a sample grown slowly and then decanted by a rapid removing of the sample from the melt. In a few places trapped liquid solidified in the same manner as in the sample shown in Fig. 1.

Jan 1, 1968

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical 'equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918

An Engineers' Symposium was held Wednesday evening, Mar. 26, in the auditorium of the Engineering Societies Building, 29 West. 39th St., under the general auspices of the Local Sections of the American Institute of Mining and Metallurgical Engineers, American Society. of Mechanical Engineers, and the Society of Automotive Engineers. It was participated in by members of the American Institute of Electrical Engineers, American Society of Civil Engineers, American Chemical Society, American Electrochemical Society, American Institute of Chemical Engineers, American Society of Heating and Ventilating Engineers, American. Society of Refrigerating Engineers, New York Electrical Society, Brooklyn Engineers' Club, Illuminating Engineering Society, Institute of Radio Engineers, Municipal Engineers of the City of New York, Society de Chemie. Industrielle, Society of Chemical Industry, and the Society of Naval Architects and Marine Engineers. In opening the meeting the chairman, Gano Dunn,* said: The program calls this an engineers' symposium, which means a putting, together of things, and these things tonight are ideas of fundamental relations to the engineering profession and the engineering societies. Not only engineers, but all men nowadays are examining their views in respect to their relation to what we call Society. My conception of Society is that there is no such thing in the concrete sense of the word. It is an abstraction, and just in proportion as it is a generalization and broader in scope than the particulars from which it is drawn, so is it emptier of content. That does not mean that it is not important, but it does mean that we should be careful and not be led astray into a zeal for doing things for Society that we would not do for our fellow engineers and our brothers. The man who is unwilling to do something for his brother or fellow engineer and yet urges that same thing for Society-is thoroughly inconsistent and, in my opinion, wrong.

Jan 5, 1919

By Gerald J. Anderson

The Marquette District of Central Northern Michigan is the oldest of the Lake Superior iron districts with a mining history dating from 1852 up to the present. The total production of all types of ore through 1965 was 338,120, 146 long tons. Emphasis up to the 1950's was on mining the direct shipping ores; however, demands for higher-grade and better-structured ores in the last decade has resulted in a complete shift in emphasis to beneficiating the lowgrade Negaunee Iron-formation to produce high-grade iron ore pellets. The Precambrian sediments of the Marquette Range have been correlated with the Animikie Series of the Thunder Bay District, Ontario, and are contained in a westward plunging synclinorium that is approximately 3 3 miles in length and 3 to 6 miles in width. -The rock unit of major economic importance is the Negaunee Iron-formation that reaches a thickness of 2500 feet near the City of Negaunee. The primary iron content of the Negaunee Iron-formation averages 26 per cent, whereas the altered iron-formation approximates 31 per cent. The Negaunee Iron-formation has been divided into three principal types: diagenetic, oxidized, and metamorphic. The ores produced to date fall into four categories: high-grade soft ores, high-grade hard ores, siliceous ores, and concentrates and agglomerates (pellets). The soft ores generally are found in synclines and in fault-trough structures, bounded by mafic dikes along at least one side, and are mainly found in the basal portion of the Negaunee. In contrast, the hard ores occur in the uppermost portion of the Negaunee and are controlled by structural features such as folds, faults, and dikes. Iron-formation that has undergone diagenetic and metamorphic alteration makes up the main beneficiating ore types. Studies on the Negaunee Iron-formation have played an important role in the formulation of many of the theories on the origin of the Precambrian iron-formations.

Jan 1, 1968

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

The following is a list of members who died in 1928. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year or Date or Biography Election Name Death 1928 Page 1914 Adams. David T.................... July 22 October 471 1905 Aguilera. Pedro................... May 3 October 469 1902 Althouse, H. W.................... NOV. 3 December 559 1920 Averill: C. C...................... July 9 October 471 1915 Baldwin, C. Kemble............... Aug. 9 October 471 1926 Barquist, Walter C............... NOV. 14 June 298 Barron,* Clarence Walker......... Oct. 2 November 511 1917 Beasley, Fred E.................... Aug. 31 October 471 1901 Belden, S. B....................... May 15 July 333 1927 Binney, Edwin, Jr.................. Dec. 29 February 96 1915 Bonsall, James Malcolm............ Feb. 12 June 284 1917 Boyle, John....................... July 12 December 561 1913 BradEn, Eugene B............. Jan. 29 March 157 1889 Bulkley, Frank.................... Mar. 25 May 240 1896 Callaghan, J. T., Jr............... Apr. 1 1892 Chalmers, George.................. Feb. 4 April 197 1898 Clark, Josiah H.................. May 7 July 333 1887 Copeland, F. K............. Nov. 10 December 561 1915 Cunningham, B. L11............... Dec. 6 August 294 1888 Dana, R. T........................ Aug. 20 December 559 1907 Dennis, Clifford G............... Dec. 28 March 1 1920 DeVenny, Thomas................ Feb. 13 April 197 1882 d'Invillier-, Edward V........... Jan. 4 March 157 1884 Duncan, M. M..................... Dec. 17 February 96 1924 Dyrssen, WaldemaR ............... Aug. 4 October 471 1906 Edmondson. H. W................ Dec. 21 February 1884 Emmerton, F. A.................. Oct. 9 June 298 1911 Eu, S. H............................ July 20 February 1917 Farrand, Ira W.................... Sept. 6 October 469 1900 Fell, E. Nelson...........•......... Mar. 25 May 231 1918 Fenton, Clarence M.............. October Junet 298 1908 Ferraris, Erminio................. Sept. 22 June 298 1914 Galloway. A. D. R............... December April 215 1924 Grant, A. W., Jr................... .4pr. 5 June 285 1917 Grant, Clifford G............... Jan. 26 January? 37 1918 Grant, Frank E.............. Jan. 14 September 417 1921 Gunderoth, C. J.................. Feb. 15 1897 Harms, Ernest..................... Aug. 12 November 512 1891 Hartrick, J. S..................... Feb. 9 June 285 1925 Hochschild, Berthold.............. Jan. 24 April 197 1917 Hutton, L. W...................... NOV. 3 January 37 1894 Jenning", S. J...................... NOV. 17 December 560 1925 Jones, J. Ravenscroft............... Jan. 29 March 157 1880 Jones, J. T......................... May 4 June 284

Jan 1, 1929

IN CIRCLES where mining men are wont to fraternize, a statement often heard is: "Yes, I spent six (or two, or ten, or thirty) years down at 'Chuqui.' " This means Chuquicamata, the site in Chile of what in all probability is the world's largest deposit of copper ore. One hears similar remarks regarding Braden and Andes, and, in fact, regarding a score of other big mines in South America, Africa, and elsewhere, but Chuqui seems to lead the others as the locale of engineers who have done a stint in foreign countries. One reason probably is that it is the Anaconda Company's premier foreign operation. Because of its unusual size and the diversity of its operations a great many men are needed. It is a sort of training school for young engineers; but, also, Anaconda has sent down a great many mature members of its big organization for special assignments like metallurgical research or plant construction. Chuquicamata is about 150 miles northeast of Antofagasta, at an elevation of 9,500 ft. It is in an almost rainless desert country where the wind (it is alleged by some) blows most of the time. However, the copper mining entrepreneurs have done their best to make up for what nature has neglected to do in creating a pleasant environment for the people who operate the mines. These include about 160 "foreigners" of whom 86 are from the United States, most of them accompanied by their families. There are 165 Chileans on the staff. Comforts, conveniences, and many luxuries are provided to offset in some measure the disagreeable features of the climate. Nevertheless, as I have implied, engineers at Chuqui generally jump at the chance to become "alumni" when opportunity offers. At the same time, they appear to take pride in their alma mater.

Jan 1, 1957

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By Albert E. Wood, Edgar R Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By Albert E. Wood, Edgar R. Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By Herbert Kilburn Scott

The information in this paper was collected by the author during a five years' residence in the State of Minas Geraes. Outside the State itself, very little is known of the gold-field. Such accounts as have been published are antiquated and contained in publications mostly out of print. The increased attention now attracted to the natural resources of Brazil, and the probability that American capital will be, in the near future, largely invested there, will make an up-to-date account specially useful at this time. I. Historical and General. Soon after the Jesuits founded what is to-day the city of S?o Paulo, gold was discovered in the streams of the neighborhood; and this incited the natives, known as paulistas, to look for it farther afield. After many expeditions into the interior, gold was found in quantity in placer-deposits in the vicinity of Ouro Preto, in 1699, by a prospecting party headed by Antonio Dias. The name of Ouro Preto (black gold) was given because of the superficial dark coating of the gold, and the inhabitants of the district were known as mineiros (miners). Later on, the placers of Cuiaba, in the State of Matto Grosso, were discovered in 1718, and those of the State of Goyaz in 1724. All this territory was at the time a private colony, but on account of its increasing importance it was taken over by the Crown, and in 1739 a royal governor was appointed, with his nominal capital in S?o Paulo, though for a number of years the real capital was Ouro Preto. In 1711 Ouro Preto was raised to the rank of a city, with the name of Villa Rica de Ouro Preto (" rich city of black gold"); and in 1720, by reason of administrative difficulties, Minas Geraes was constituted a separate colony from S?o Paulo, with Villa Rica as its capital. The site of this city

Jan 1, 1903

By D. V. BURR

THE ORIGINAL HUDSON RIVER TUNNEL. NOT quite forty years ago a man of uncommon character entered New York. He had several hundred thousand dollars earned by railroad building in the Nest. He was not an engineer, but he had ideas of engineering work which he was destined to prove correct.. He introduced new ways of tunneling, but his plans had only one distinguishing feature-they were simply interesting as showing how such work could be done; they added nothing to the science, have never been used since his clay, and never will be used again. Engineers of repute ridiculed his proposition ; he was an Ishmael in the profession. But if engineers looked askance at him, he certainly returned their contempt in the heartiest fashion, and had no hesitancy about expressing his views of them individually and collectively. This worked to. his disadvantage when he afterward tried to raise the means to go on with the work. He found that the opinion of engineers was respected by financiers, and that money would not flow contrary to their advice. While his conception of large constructions was distinguishingly original, much more marked was his method of demonstrating the feasibility of, his schemes. In the present clays of great undertakings it is the custom to make the other man pay for the experiments. But the man from the West had other notions of how the thing ought to be done. Having wonderful confidence in his own ability and in his perception of the task before him, he used up all his own money before seeking outside assistance. By building several hundred,, feet of tunnel he proved the correctness of his theory, and the tunnel then dug forms a part of the present tube. The result-he failed to finish the tunnel. He was blind in

Mar 1, 1908

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of in- creasing importance to the economic life of the northern field operations. Successful approaches have Been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas; the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 1, 1950

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By R. H. Oliver

The purposes, types, preparation, and testing of flocculants are discussed. A flocculation compendium is included, indicating choice of flocculant for a given set of conditions. An economic evaluation of the process is presented. Solid-liquid separation is a major expense in most mineral processing flowsheets today. Proper use of flocculation can often lower the overall cost of a solid-liquid separation by reducing the size of sedimentation or filtration equipment. PURPOSE OF FLOCCULATION When is use of a flocculant justified in terms of overall process economy? 1) when it results in process improvement, such as producing a clear liquor for electrolysis, precipitation, ion exchange, or solvent extraction; 2) when it results in satisfying requirements of pollution abatement ordinances; 3) when it results in increased recovery of values that would otherwise be lost; or 4) when it results in considerable savings in capital expenditure due to use of smaller equipment. When can the use of a flocculant adversely effect overall process economy? 1) when it results in increased filter cake moisture, 2) when it results in decreased filtration rates, 3) when it results in considerable bulking of sedimentation underflow, 4) when it contaminates either the supernatant or sludge, or 5) when the cost of using the flocculant is greater than the savings due to its use. First step in consideration of flocculants for a given application is establishment of desired goals in terms of increased clarity of effluent, increased recovery of solids, or decreased size of equipment. The most economical solution to a solid-liquid separation problem is that combination of equipment and flocculant costs which meets the established goals at the lowest total annual expenditure. This economic decision can be made only after technical data has been obtained as outlined in next four sections. TYPES OF FLOCCULATION Flocculation is a process wherein individual particles are united into more or less tightly bound agglomerates or flocs, thereby increasing effective particle size of solids suspended in a liquid. Degree of flocculation of a suspension of finely divided solids in a liquid is controlled by a combination of probability of collision between particles and probability of adhesion after the collision has occurred.&apos; Probability of collision can be increased commercially through use of a paddle-type flocculator, combination flocculator, and clarifier or flocculating-type feedwell. Probability of adhesion usually can be increased by addition of a reagent known as a flocculant. Reagents act as flocculants through one or a combination of three possible mechanisms. The first is electrolytic neutralization of inter molecular repulsive force due to Zeta potential. This neutralization enables Van der Waal&apos;s cohesive force to hold the particles together after they collide.&apos; The second is the precipitation, within a definite pH range, of voluminous metallic hydroxide flocs which entrap fine particles. This process is known as coagulation.14 Third is the bridging of two or more particles by either natural or synthetic long-chain, high-molecular-weight organic polymers. This bridging is accomplished by adsorption of two particles at different sites on the same molecule or by bonding of two molecules, each adsorbed to a different particle. Considerable effort has been expended in explaining the action of these polyelec-trolytes and detailed accounts are available in the literature. CHOICE OF FLOCCULANTS It is impossible, at the present time, to specify the optimum type or amount of flocculant for a given application from a knowledge of the material to be treated. The standard procedure is to choose reagents or combination of reagents most likely to be effective on the slurry; then test them.&apos; The accompanying Flocculation Compendium (Table I) contains details of all currently available reagents sold as flocculants and it should be used when selecting the group of reagents for tests. This selection can be based on information listed in columns 4 and 5. Column 4 presents industries in which each floc-

Jan 1, 1961