Search Documents

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By Frank B. Fulkerson

Barge traffic on the Nation's inland waterways over the past 15 years has been increasing at a rate much faster than intercity freight traffic by all modes, largely due to the growing consumption of mineral commodities, development of more powerful towboats and large and more specialized barges, improvements to loading and unloading facilities, and competition among bargelines for contract shipment of bulk commodities. The Bureau of Mines, in a study to determine barge traffic projections for inland waterways in the South-Central States to the year 1980, gathered data on origin-destination patterns by commodity, quantity moved, equipment used, and rates charged; the trend of each of these factors over time; and the extent of competition between water trans-port and other means of transportation. The Mississippi River and the Gulf Intracoastal Waterway, which together carryover half the Nation's barge traffic, are major carriers of coal, crude petroleum, steel, marine shells, sulfur, salt, cement, and alumina. Greater quantities of these products will be transported by barge; however, oil pipe-lines and unit trains for coal are expected to limit increased barge traffic of these two commodities. Increasing quantities of fertilizer materials will be transported upstream. Although congestion at certain locks is a current problem, the Mississippi River below St. Louis and other open-river stretches have the capacity to handle the increasing number of barges for the foreseeable future.

Jan 1, 1969

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar (CaF2) from 36 U.S. and 50 foreign mires and deposits in 13 countries. Only 6 U.S. properties are considered to be economic, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0-pct) discounted-cash-flow rate of return (DCFROR). The 50 foreign properties evaluated represent at least 55 pot of demonstrated fluorspar resources located in market economy countries and China. Al I evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars when compared against published prices for each country. Reserves for 56 properties totaled 97 million metric tons (mt) (recoverable Ca F,) from demonstrated ore resources of 344 million mt that contained 123 million mt CaF2. The average total cost needed to cover all costs over the life of each operation was determined for all recoverable fluorspar products. Comparisons of ruining, beneficiation, and transportation costs per metric ton of fluorspar concentrate illustrate advantages between countries. Of the three countries with the greatest fluorspar production, China, with its high-grade, low-cost operations had the lowest weighted-average total cost of production ($38/mt concentrate), Mexico was next, at $54/mt concentrate, and benefited in U. S. dollar terms from the devaluation of the peso. The Republic of South Africa needed an average of $90/mt of concentrate to cover all costs of production at its large low-grade deposits.

Jan 1, 1985

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

By D. P. Harris

This paper examines recent developments and work in progress on the application of quantitative methods and computers to the appraisal of the mineral resource potential of discrete areas by employing reconnaissance geological information and general economic relationships. The perspective of this paper might be that of a firm planning a regional exploration program or of a legislative body seeking to choose between several alternative actions on the basis of their impact upon the regional resources. In addition to this general survey and commentary, an example is presented of the use of geostatistical analysis and computer simulation to evaluate the economic mineral resources of the Seward Peninsula of Alaska.

Jan 1, 1969

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By D. Hoffmann, S. Plumb

IRUP is an iron-rich ultramafic pegmatite rock that formed due to hot ironrich fluids and gases replacing local stratigraphic zones of the Bushveld Complex. This study focuses on the estimation of the probability of IRUP occurrence on the Merensky Reef at the Marikana Karee Mine. A 2.15 million centare IRUP-rich domain at the Karee Mine was initially defined from the interpretation of a surface aeromagnetic anomaly, and exposures in the mine workings. Surface boreholes (spaced 250-500 m apart) within this IRUP domain contain approximately equal numbers of IRUP-replaced and IRUP-free intersections. Owing to the uncertainty in the continuity of the IRUP alteration (a result of the wide borehole spacing), the risk associated with the development of mining infrastructure within this domain is unquantifiable. Semi-quantitative data comprising visual estimates of IRUP replacement from reef development mapping data and surface borehole reef intersections was interpolated into blocks using indicator kriging estimation. Comparative analyses of the estimate of IRUP occurrences were made by changing the block size and declustering the data systematically. Reconciliations of the probability of IRUP predicted from the block models derived from the different data-sets and sequential indicator simulation models were analysed for four mining study blocks. A quantitative approach to modelling the occurrence of IRUP can be an additional tool for refining the estimate of the geological losses that inform the mine plan in such high-risk zones.

Jan 1, 2015

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By D C. Grant, D J. Goudie, E Baird

The Scanning Electron Microscope – Mineral Liberation Analyzer (SEM-MLA) laboratory, as part of the Core Research Equipment and Instrument Training (CREAIT) network of laboratories at Memorial University, NL, Canada, has recently published efforts towards increasing the throughput of automated mineralogy systems by producing single-step trans-vertical moulds, rather than traditional 30 mm polished epoxy moulds. Due to the small particle size of iron ore grains in the -200 mesh size fraction (<75 µm), not all of the surface area on a mould is needed for measurement in achieving good statistical representation. In a new study, trimming of the excess area of a mould results in a smaller sample and increases the quantity of unique samples that can fit in a newly designed trans-vertical adapter for a FEITM MLA 650 field emission gun (FEG) scanning electron microscope. The complete analysis, using a newly designed sample block holder capable of holding 98 samples, required 57 hours of running time where each sample had an average of 33?400 particles measured and identified. The analysis was calibrated to allow for off-line discrimination of hematite/magnetite. The calculated Fe-assay values derived from MLA results were compared to those from bulk sample chemical assay. This shows the Fe assay having a correlation coefficient of >0.99 when the particle count is greater than 20?000. This study represents the most expedient method yet reported to prepare well-polished samples and analyse them in a timely manner that can allow for quicker results in process mineralogy.CITATION:Grant, D C, Goudie, D J and Baird, E, 2017. Analysis of individual - mesh iron ore samples in a single Scanning electron microscope automated mineralogy session, in Proceedings Iron Ore 2017, pp 535–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979