Search Documents

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By B Belle

In a predrained gassy coalmine, ventilation control plays a secondary role to the longwall (LW) goaf drainage systems to safely manage panel return gas levels. Typically, the LW specific gas emission (SGE) estimation models provide anticipated goaf gas emissions and arriving at required gas drainage capacity for various coal production scenarios. A study comparing the various LW goaf gas hole spacing patterns with weekly production rates of up to 270 kt/w of an operating mine with high SGE rates (~20 m3/t) was carried out. The goaf capture efficiency of LW panels ranged from 64 per cent to 85 per cent. For the first time, gas content of upper seam data post LW retreat were used to verify the current SGE prediction models. This study has shown that an average of 50 m goaf spacing is optimal for management of high production retreat gassy LW panels in presence of multiple upper and lower seams with gas emission zone influence reaching up to 200 m above workings. Due to the horizontal stress direction related geotechnical issues, goaf hole failures just behind the LW face is a recurring challenge resulting in significant and immediate increase in LW panel return gas levels. This paper highlights the shortcomings of current SGE prediction models for goaf gas estimation, and evolution of 50 m goaf hole spacing embedded in design process in managing the LW tailgate gas levels.CITATION:Belle, B, 2017. Optimal goaf hole spacing in high production gassy Australian longwall mines – operational experiences, in Proceedings Australian Mine Vent Conference 2017, pp 15–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By H. G. Denkhaus

Comment on ?The evaluation of rock brittleness concept on rotary blast hole drills? in the Journal of SAIMM, vol 102. no. 1. pp. 61?66 Comment on ?Correlation of specific energy with rock brittleness concepts on rock cutting? in the Journal of SAIMM, vol 103. no. 3. pp. 163?171by R. Altindag Foreword Some thirty years ago it was almost customary that articles in South African technical and scientific journals were followed up by discussions in which the reader(s) expressed criticism and/or added to the information contained in the article. This custom has obviously died out, be it that the articles are nowadays of such a high standard that nothing can be added or be it that the receivers of the Journal suffer from an information inflation and do not read the articles anymore. I now have the temerity to offer a discussion to an article that recently appeared in the journal, namely ?The evaluation of rock brittleness concept on rotary blast hole drills? by R. Altindag (J.S. Afr. Inst. Min. Metall., vol, 102(2002), pp. 61?66.

Jan 1, 2003

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

Treatment of the Siirt-Madenk÷y Ores by Flotation

Sep 13, 2010

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By James Barr

Geology and Mineralogy1 TENNESSEE phosphates are commercially divided into three varieties: Brown, blue and white. The first two only are now of commercial importance. The white phosphates of Perry county are not being mined at present owing to their pockety occurrence. The white phosphate is Fig. I.-DEPOSITS OF 75 PER CENT. BROWN PLATE ROCK UNDERLAIN BY SAND. the highest grade of the three varieties, running often more than 90 per cent. tricalcium phosphate. The brown rock is found in three varieties, grading from the dense almost vitreous gray rock, 76 to 82 per cent. tricalcium phosphate, down

Jan 9, 1914

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By J. Glazewski

The mining industry in South Africa has developed its own environmental guidelines in the form of an Aide-Mémoire1,which is an extension of the previous rehabilitation provisions to include all aspects of the environment and all phases of a mining operation. This development, at the time, recognized an international trend towards the formalization of environmental management in mining practice, which resulted from the realization of the large environmental liabilities that mines could face, particularly on closure. Over the past decade the international environmental focus in the mining industry has moved from operational management, to the reduction of liability on mine closure. Mine closure guidelines are being developed internationally by nations (for example, SRK, 19982) and by large mining groups (for example, Rio Tinto, 19983). In South Africa the Department of Minerals and Energy (DME) is presently reviewing the Aide-Mémoire to bring it in line with international and local developments and a separate mine closure plan is being considered.

Jan 1, 2000

By Richard W. Lusignea

This report describes a program to evaluate the feasibility of determining roof features which occur in United States coal mines from changes in bolting machine drilling parameters. The ultimate purpose of this effort is the development of an instrumented roof bolting machine which can detect hazardous roof conditions and/or indicate when the existing roof control plan is inadequate. A survey of hazardous conditions occurring in United States coal mines is included, along with the slang expressions for these conditions, and their relative degree of hazard. Specific machine parameters are identified for detecting the specific roof conditions. Measurement concepts are proposed using readily available instrumentation in most cases. Various systems are evaluated and tradeoffs presented. An implementation plan is proposed for developing a prototype system and using it in an operating coal mine.

Jan 1, 1978

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011