Search Documents

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural- gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas, in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and In solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil- bearing horizons.

Jan 1, 1936

So many emergencies that crop up in mining necessitate a departure from ordinary methods that the writer has been led to illustrate a few of the examples that have come under his notice during a somewhat lengthy career; and as most of the methods illustrated are certainly outside the ordinary, it may be hoped that while to many they may convey little that is new, to the larger number some acceptable information may be gleaned whenever the occasion calls for it. Experience has shown that there can be no hard and fast rule in mine timbering that will fit the varying- necessities of different localities, and the engineer must divest his mind of all prejudices that his practice of any particular system or systems may have induced, and must direct his attention to the character of the local timber and its fitness or otherwise for the purpose he has in view. Fortunate indeed are the man and mine that can claim an abundance of good and cheap mining timber it simplifies, oftentimes, what would be, under unfavourable timber conditions, a difficult problem. In many parts of the States there is either none or at best a scrub if the latter, he has to either pigstye, balk, or bulkhead, if his ground will permit; if, not, and the necessary timber has to be imported, then some system of recovering his timber and using it over and over again may be possible. As an illustration of this, Fig-s. Nos. I and 2 show a method applied to the copper deposits of the LyellTharsis, Tasmania. The workings were wide; varying from 30 ft. to 50 ft., and the deposit a taIcose schist of fairly good...

Jan 1, 1902

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By Patrick E. Durnal

The Richmond-San Rafael Bridge was built in the early 50s' and was first opened to traffic on August 31, 1956. Among California's longest steel bridges, it spans more than 21,000 feet across the northern portion of San Francisco Bay. It is one of six toll bridges currently undergoing seismic retrofit in the Bay area. Current retrofit criteria require the structure not to collapse in a Magnitude 8.3 earthquake lasting 45 seconds on the San Andreas Fault. The earthquake epicenter is 10 miles to the west of the Bridge, near the mouth of San Francisco Bay. Another major fault is the Hayward Fault, with a potential of a 7.5 magnitude earthquake. It is only 4 miles east of the eastern end of the bridge. The retrofit criterion is that the structure survives these earthquakes without collapse or loss of life, and that they are capable of repair within a period of one year. Therefore an energy absorbing, ductility and nominal resistance based approach to the retrofit design have been adopted for the retrofit of this bridge. Foundation Retrofit The foundation retrofits were designed to satisfy of drift criteria of 6 inches at the base of the footings, and to keep the existing H-piles from experiencing unacceptable levels of permanent soil displacement and /or structural rupture. Full-scale structural lateral load testing of BP14x89 piling, to rupture, has helped to determine the drift criteria. However recent non-linear analytical results, have led to a redesign, which may allow for 12 inches of drift. The as-built analysis of the Micropile piers determined that those piers would not exceed the 6-inch drift criteria so lateral resisting shear piles were not needed at those piers.

Jan 1, 1998

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

By Mario E. Rossi

Las simulaciones condicionales geoestadísticas se utilizaron como herramientas de control de leyes en operaciones diarias que evalúan la incertidumbre y el riesgo de las reservas mineras en estudios de factibilidad, así como el potencial de mineralización en ciertos ambientes geológicos. Otras aplicaciones incluyen evaluación de recursos y reservas recuperables (dilución), clasificación de recursos y reservas, y optimización de espaciamiento de sondajes. En ese sentido, el presente trabajo señala los aspectos de los esquemas de clasificación de recursos y reservas utilizados en la industria, el cual está basado en el modelo de incertidumbre que las simulaciones condicionales proveen. Asimismo, se analiza el riesgo que este modelo de incertidumbre implica para sub-regiones (unidades) de extracción del yacimiento, como las definidas por fases de extracción mineras o períodos de tiempo.

Jul 17, 2000

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

Mineral ownership determination is not always straight forward as in many cases the relevant details are not recorded on the latest Land Transfer title held in the local Land Registry Office. To determine mineral ownership can be difficult, time consuming and expensive especially in a confused sector. Non statute minerals can be owned by the Crown, Land Owner or other persons. Statute minerals (Gold, Silver, Petroleum, Uranium) are always owned by the Crown and thus present no problems. In simple terms the only accurate and reliable method of determining the mineral ownership under subject land is to historically search back to the first registration when the land and minerals were definitely intact. Then carefully ascertain from the evidence gathered along the way to the present day whether any legislation or private agreement altered or affected the status quo.

Jan 1, 1998

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By Mark Ioli, Debra Struhsacker

In September 2004, Gale Norton, U.S. Secretary of the Interior, presented the Manhattan Mine with a U.S. Bureau of Land Management’s 2004 Hardrock Mineral Environmental Award. The Manhattan Mine is a sustainable development showcase. The reclamation accomplishments at this Nevada gold mine demonstrate how modern reclamation techniques can restore an old mining district into an aesthetically pleasing landscape that can support multiple and sustainable uses. In a collaborative effort that relied on substantial community involvement, Round Mountain Gold Corp.(RMGC) has improved the environment and eliminated a number of public hazards associated with old, unsafe mining features. RMGC’s community collaboration, innovative engineering, creative reclamation design and corporate commitment to environmental excellence show what Secretary Norton’s 4 Cs Initiative looks like on the ground and inaction.

Jan 1, 2005

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand. The reform of New ZealandÆs minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Governments intention to review all the major laws governing New ZealandÆs resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990. With some matters still to be determined (at the time of writing), this paper cannot be a definitive review and description of the new legislation, it is instead an attempt to outline the major features of the Bill, to date, that are seen as important to the mining industry.

Jan 1, 1990

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

Although auriferous beach and fore-dune sands at Five Mile Beach south of Okarito township had been intensively mined by hand and primative mechanical methods drilling of the sandspit by the Gold Development Corporation in 1929 indicated that the grade and quantity of undisturbed black and grey sand below the water table was sufficient to support a mining operation. Worked sand above the water table also contained fair prospects. The Okarito Five Mile Beach Gold Dredging Co Ltd, was formed and an hydraulically powered, bucket ladder, sluice box dredge built. In 13 years of operation (1931 - 1943) the dredge returned 556.39 kg (17 890 oz) of gold at a recovered grade of 225.4 mg/m3. A total of ú42 000 was distributed as dividends on the ú30 000 capital investment. Recent drill and bulk sampling at the northern end of the beach has confirmed that reworking of the historic tailings by a modern gravity recovery plant would not be economic.

Jan 1, 1993

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. &apos;Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring&apos; the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more &quot;direct&quot; technique, such as by &apos;Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

By Charles E. Locke

CONTINUED expansion of gold mining in 1935 led to further developments in treatment methods. In base metals and non-metallics progress is also noted, coincident with greater activity. Statistics are not available yet for 1935 but the trend is shown by 1934 when nonferrous ore mined in the United States was 35,840,737 tons, or 45 per cent more than in 1933. The amount concentrated was 27,167,530 tons or 75.80 per cent of the ore mined, and flotation was used in whole or part on over 96 per cent of the ore subjected to concentration. In the crushing field a new model of the Fahrenwald crusher is promised soon. The Symons fine-reduction cone crusher and Traylor secondary crusher continue to gain as intermediate crushers. A new book entitled "Crushers for Stone and Ore" by William T. W. Miller appeared. The Hadsel mill has been improved still further and a number of installations are in satisfactory operation showing economical power consumption and low wear. An attempt in a

Jan 1, 1936