Search Documents

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By k. Osei-Boakye

This paper presents the calibration of a real-time aerosol monitor, the TSI DustTrak?, to the NIOSH 5040 method being used by the Mine Safety and Health Administration (MSHA) for compliance enforcement evaluation. The standard NIOSH 5040 instrument for compliance evaluation of diesel particulate matter (DPM) has an inherent time lag of up to two weeks for laboratory processing of sample results. Therefore, providing the underground mines with a means of quantifying DPM conditions in real-time, will enable them to efficiently and effectively manage DPM levels to ensure compliance with the regulated limit.

Jan 1, 2009

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By William J. Douglas

Critical path modeling (CPM) has been used widely as a tool to manage large-scale projects having many activities which are conducted in series or parallel. The construction industry is a regular user of critical path modeling as a planning tool. In this context, the method is used to provide an orderly schedule for all activities to forecast delays, slippages, and problem areas and to identify critical activities where resources should be directed. It also identifies others which have slack time, and provides information on the degrees of freedom and flexibility available in completing the project. The purpose of applying critical path modeling to an underground mining system is not primarily for scheduling, but as an analysis tool. In observing underground mining systems, it Is clear that repeated sequences of activities must take place for mining to proceed efficiently. Some of these activities must be sequential, while others be carried out in parallel. The fundamental difference between critical path modeling applied to mining versus a large-scale construction project are: (1) The activities in a mining system are cyclic in nature. (2) The location of the activity varies, and the entire process is not thought of as co-located, as is the case in a construction project. Another important aspect of the network development for mining systems is the degree of detail that is desired. One can be concerned with very macroscopic networks which represent, for example, an entire mine life cycle. Networks representing this problem would be more closely analogous to those of a large construction project. On the other hand, one might be interested in evaluating alternative ways of developing a property or of mining in a given section. More detailed networks representing the section activities are necessary to evaluate system parameters and their impact on long-term production.

Jan 1, 1978

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946

By Phillip R. Moyle

A mineral survey of 19,350 acres of the Gooding City of Rocks Wilderness Study Areas (WSAs) in the north-central Snake River Plain was conducted by the U.S. Bureau of Mines in 1984. No formal mining districts are known in or near the study area. Forty-two placer claims within and adjacent to the study areas cover the Clover Creek diatomite deposit. Minor production from four pits was reported by the owners. The diatomaceous sediments are underlain by dacitic welded tuff and capped with basalt. Five exposures or blocks totaling 416 million tons of the diatomaceous material comprise the Clover Creek deposit; four of the blocks are in the study areas, out are predominantly covered by basalt. The North Clover block, just west of the areas, is only partially capped, and could be mined by open pit methods on the western flank of the exposure. The minable wedge contains an inferred marginal reserve of 35 million tons of diatomite possibly suitable for filter aid, filler, insulation, and other applications. At a production rate of 150,000 tons/year, total mining and milling costs for high-grade filter aid diatomite would be about $100/ton. The deposit is classed as marginal because products from this deposit may be inferior to currently marketed diatomite products. The market is well supplied by developed sources.

Jan 1, 1985

By A. J. Neale, B. C. Flintoff

"In most mineral processing operations the term audit is usually reserved for the exercise of checking financial records and/ or safety practices. While these activities are time consuming, no one disputes their necessity or value. If we subject these areas to such careful scrutiny, why is it that we don't normally apply the same principles to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance, in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focused manner. Experience teaches us that the exercise is very revealing and potentially very rewarding.This paper will discuss the process audit process and illustrate its potential value through illustration taken from plant studies.IntroductionThe last twenty years have seen tremendous technological and organizational changes sweep the minerals industry. Process control systems, on-stream analyzers, and gold recovery techniques barely conceived twenty years ago are now incorporated in virtually all new installations in an effort to maximize operating efficiencies. In conjunction with these developments, changes in the way plants are managed, down-sizing of technical staff, reduction in the size of operating crews, and the flattening out of the management structure have significantly reduced operating costs. As a result, plants are making more efficient use of our natural resources, minimizing the costs of production, and in turn maximizing operating profits. Or are they?"

Jan 1, 1991

By D. A. Keefe, O&apos

The electrowinning of beryllium from beryllium oxide (BeO) using a molten-salt electrolyte composed of 56 LiF-37 BeF2-7 BeO (mole-percent) was investigated. Anodes made of porous carbon were found to be superior in current-carrying capacity and gave a lower cell voltage than other types of anode material tested. When porous carbon anodes were used) the resultant increase in anode area prevented anode passivation. The cell voltage was 3.3 volts) and electrode current efficiencies of 50 to 70 percent were obtained. The electrodeposited beryllium was recovered as beryllium powder or was coalesced to metal beads by heating to 1,300° C.

Jan 1, 1970

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Sep 8, 2021

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Oct 1, 2021

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By W. M. Peirce

Commencing in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very- broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole. to pain: out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount . that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things' Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944

By W. M. Peirce

Commencing in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very- broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole. to pain: out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount . that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things' Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944