Search Documents

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had' under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman's report was published in the Engineering and Mining

Jan 10, 1910

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003

The theme of this paper is the development of-the project feasibility study which includes discussion of the work which is carried out in preparing the project feasibility study, the necessary evaluations and structures that are employed to ensure that not only does the feasibility study itself stand up to scrutiny and is sound, but also that the investment the company is proposing to develop, "the project", is an investment decision which will represent good returns to the company. This theme is particularly relevant when there are competing divisions within the company and only limited cash resources are available to make the correct investment decision. Thus various potential investments may be evaluated against each other to determine which project will be given the go ahead for development. This paper will particularly focus on the various investment analysis techniques that are used and discuss the work that is required in preparing the project feasibility study and specifically the interaction of the project team members and the thought process that must be undertaken to complete the project feasibility study. Finally comments will be made on tax planning issues particularly with respect to taxation of gold production to be introduced in January 1991. Some ideas are presented which may help and possibly improve the financial position of the projects being reviewed. Further, it is suggested that the thought process which goes with the financial engineering aspects of a resource project can be widened to take account of taxation issues and tax planning to ensure the rise of the project feasibility and hence the decision to proceed to development by the project sponsors.

Jan 1, 1990

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By Kevin Whipkey

How is Improvement Being Achieved ? Section Equipment ?Mine Layout/Projections ? Work Schedule ? Maintenance ? Management

Jan 1, 2005

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

This list is part of the long-range conservation program of the Bureau of Mines and is intended for use by those interested in the Bureau's publications dealing with oil shale and shale oil. The items included represent 51 years of research by Bureau of Mines employees on oil shale and shale oil and are available at any U.S. depository library. DISTRIBUTION U.S. Bureau of Mines report series contain both free and sales publications. An asterisk (*) designates publications for sale. Such publications can be obtained from Superintendent of Documents U.S. Government Printing Office Washington, D.C. 20402

Jan 1, 1969

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By C. A. Brown

"Steady-state simulation has been used for over 20 years to optimise the operation of crushing and grinding circuits. Throughout that period continuing comminution research has been the basis for improving the models.Site surveys, ore characterisation, model development and investigation of different operating scenarios by simulation has proved to be a cost-effective method for improving plant performance. In this sense, this paper presents findings from experience with these valuable optimisation techniques with reference to specific case studies."

Sep 12, 2005

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966