Search Documents

By lchiro Aoi, Hideo Nakae, Makoto Yoshida, Makoto Ishino

"The influence 6f gravity on the microstructure of unidirectionally solidified Cu-Pb monotectic, Ag-Si and Fe-C eutectic alloys is studied. In order to examine the influence of gravity in a lg environment, both the upward (opposite to direction of gravity) and downward (direction of gravity) unidirectional solidifications are carried out. The results are as follows: (1) For the upward solidified Ag-Si eutectic alloy, the eutectic Si continuously grows. On the other hand, in the downward solidified Ag-Si alloy, the Si grows discontinuously and disperses into the ex-Ag matrix. (2) No morphological difference in the eutectic growth is observed between the upward and downward solidified Fe-C eutectic alloys. (3) In the case of the upward solidified Cu-Pb monotectic alloy, a banded structure, which consists of Pb-rich layers and Cu-rich layers, is observed. However, such a banded structure -is not observed in the downward specimen. (4) The banded structure is not found in the upward solidified Cu-Pb-0.05 mass % Al and Cu-Pb-0.1 mass % Al alloys. In the Cu-Pb-0.05 mass% Al alloy, a fibrous -L 2 phase grows continuously parallel to the growth direction at low growth rate. Only 500 mass ppm addition of aluminum induces the morphological change of the monotectic L2 phase.IntroductionThe influence of gravity on the solidification of eutectic and monotectic alloys has been investigated in microgravity environments [l-9]. The purpose of these studies was to obtain a homogeneous microstructure of eutectic or monotectic alloys, most of which alloys tend to solidify with macro-segregation under gravity. However, in most of the previous experiments, e.g., in free fall systems, in aircraft or in space laboratories, the growth rate was too high to realize a planar solid/liquid interface. This would be due to the limited time for solidification. Thus, it was difficult to examine the influence of gravity on the planar coupled growth of the eutectic or monotectic alloy. In this study, both the downward U.D.S. (unidirectional solidification by gravity) and upward U.D.S. (opposite direction to gravity) are carried out in order to examine the influence of gravity on the coupled growth in a lg environment [l0, 11]. In the case of the downward U.D.S. using the current Bridgman method, the molten alloy must be confined between the crucible and the solid."

Jan 1, 2000

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By Wei Luo, Yuanbo Zhang, Zhixiong You, Zijian Su, Guanghui Li, Tao Jiang

"In this study, the appropriate sintering process parameters for low-grade ferromanganese ores were investigated. The results showed that, under the condition of natural basicity (R=0.03), the optimal parameters were obtained as follows: moisture of mixture 9 .1 %, coke powder 9 .9% and sintering negative pressure 7 KPa. And the corresponding yield, ISO tumbling index and utilization coefficient reached at 80.18%, 61.27% and 1.515t·m-2·h-1, respectively. Under the optimal parameters, the emission of harmful gases, such as S02 and NOx, were reduced evidently with 30% of coke powder replaced by biomass charcoal. Moreover, it was found that the basicity had obvious effects on the quality of the sinters when it changed between 0.03 and 2.4. The ISO tumbling index gradually decreased from 61.27% to 55.47% with the basicity increasing from 0.03 to 1.2, then, it began to increase after the basicity further increased to 2.4.IntroductionManganese is mainly consumed by steel and battery industries, particularly in the steel plants and ferroalloy units. The consumption of metal manganese in the ferroalloy industry accounts for 85%-90% of the total Mn [1-2]. Therefore, ensuring sufficient manganese alloys is essential to meet the rapid development of steel industry. Recently, rich-manganese slag containing high grade Mn (>40%), low Fe (1%) and P (<0.03%) is considered as superior raw materials for manganese alloys. While the sinters made from manganese ores are major raw materials for producing rich-manganese slag with the increasing exhaustion of natural rich manganese lump ores [3-5]."

Jan 1, 2013

By R. Kola

Since more than 15 years the Waelz process at "Berzelius" in Duisburg has proved suitable for reprocessing the zinc and lead containing dust and .sludge which inevitably occur in making steel in EAF-plants. The produced Waelz-oxide is agglomerated in a hot-briquetting plant and charged to an Imperial Smelting Shaft Furnace to recover the valuable elements in form of metallic zinc and lead. In view of the actual importance of the dumping problems of the EAF wastes a description of the "Berzelius" treatment route is given but also the situation in Western Europe is illustrated. Dust from stainless steel production is successfully treated in the Scan Dust Plasma Process in order to recycle Chromium and Nickel, while the resulting Zinc-Dust is treated via the Waelz-ISF-Route. For treatment of low Zinc-containing dust, sludge and fines from integrated steelworks, pilot scale tests have been carried out successfully in the Circulating Fluid Bed in order to recover metalized iron and .zinc/lead fume. A 30,000 tpy Demonstration Plant is planned?.

Jan 1, 1990

By Vinicius Alves Gomes, Jean Igor Margem, Frederico Muylaert Margem, Sergio Neves Monteiro, Marina Rangel Margem

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and, consequently, affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of malva fiber in epoxy matrix composites. A small critical length was found for the malva fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2015

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By K. Alibhai

Greek laterites, which generally had nickel concentrations of < 1 %, are amenable to chemical leaching,. although there is considerable variability in the ease of leaching with different ore types. With low grade ores(< 1 % Ni content); >70% of the nickel was leached in columns with a strong selectivity for nickel over iron. Heterotrophic microbially assisted leaching could be a viable alternative to classical hydrometallurgical and/or pyrometallurgical techniques, with a very high recovery (greater than 80% ) being found with some of these mineral microbial interactions. Critic acid was probably the effective chelating agent.

Jan 1, 1991

By Hong Yong Sohn

A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

Jan 1, 2014

By J. Schmidl

In non-ferrous metallurgy the service life of refractory materials typically ranges from several weeks up to three years or more and is strongly dependent on operating conditions. To support our customers with the most viable refractory solution for their needs RHI Magnesita follows a structured approach of thermo-chemical calculations, experimental evaluation from lab scale up to industrial field tests and post-mortem analysis of used refractory materials. This paper will give an overview of the RHI Magnesita refractory selection process and the most recent developments of the experimental setup for the so called HF-IF test. This is a dynamic corrosion test that allows to determine fundamental properties of different refractory material types under process conditions subjected with respective customers process materials. The HF-IF experimental procedure is an excellent tool to simulate refractory wear in industrial processes, diminishing risks associated with plant trials and support decision making to choose the optimal refractory solution for the customer.

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008

By V. I. Lakshmanan, R. Roy

"TiO2 is used in paints, plastics, rubber, paper, inks, textiles and other miscellaneous applications. The demand for the pigment grade Ti02 is growing at 3.0%/year on average and this invites the development of innovative and cost effective processes. The current processes are not designed to recycle the reagents and thereby discharge the effluents into the environment, causing an environmental concern.During this study, synthesis of TiO2 from an ilmenite concentrate was investigated using an innovative atmospheric mixed-chloride leach process. The solution purification was carried out using solvent extraction in two stages. In the first stage iron removal was carried out and in the second stage titanium was extracted. The strip solution obtained from the second stage solvent extraction contained the purified titanium and from this stream pigment grade Ti02 was recovered. The barren solution was used for reagent recovery and the regenerated leach liquor was recycled."

Jan 1, 2011

By QinGuo, Shenghui Guo, Lei Li, Jinhui Peng, Linqing Dai, Libo Zhang

The ferrous removal process after carbothermic reduction of chromite fines with microwave heating combined with leaching was investigated. Under the following conditions: Reaction temperature: 1150 , Reaction time : 40min, Semi coke ratio: 12% , the iron content of the reduction product : 13.05% . Metallization achieved was 52.7%. Reduced chromite was leached with 8% of H2SO4 and FeCl3 aqueous solution. The results show that: the recovery rate of chromium can reach 88.06%, the mass ratio of chromium to iron is 3.5:1 for leaching 30 minutes with 8% of H2SO4; the recovery rate of chromium can reach 88.91%, the mass ratio of chromium and iron is 2.56:1 for leaching 4h at room temperature with FeCl3 aqueous solution (100g/L). The leaching time of latter is longer but can realize the circulation effectively and reduce the waste liquid processing problem.1

Jan 1, 2016

By G. Fazel Jahromi

Enargite, known as one of the major arsenic containing copper minerals, with approximately 19% arsenic, introduces challenges to typical processing options. In most hydrometallurgical processing methods, arsenic remediation occurs after the copper recovery in an autoclave or in a stepwise neutralization process. In this study, the in situ precipitation of scorodite was investigated during an atmospheric leaching process in the presence of carbon-based catalysts and chloride media. The effective parameters of initial ferric addition, temperature, catalyst addition, and oxygen sparging rate were studied and the ferric behaviour was monitored during the scorodite precipitation. The most influential parameters on efficient scorodite precipitation are found to be: initial ferric addition, catalyst to concentrate ratio, and temperature. A 99% scorodite precipitation yield was achieved in this process.

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"A cellular model of the plastic deformation of polycrystalline aggregate is proposed and comprehensively described. Representative volume element (RVE) of a solid body, that is being deformed, is described as a population of interconnected units that, in turn, can consist of lower scale level units. Sliding along the various allowed sliding systems deforms simple units, which do not have an internal structure. For consideration of stress distribution within the limits of components, the approach of self-consistent field is used. Rotation of units and moment stresses connected with it are taken into account. Results of computer experiments are analyzed.1. IntroductionMicromechanical models of polycrystals are a link between the research of plastic deformation on micro and macro levels. Computer simulation of inelastic strain of polycrystals has found a great deal of interest as well. Despite the fact that this approach does not allow to obtain macroscopic constitutive relationships that are used in deformed solid body mechanics, it clarifies essential features of the phenomena in many aspects. First of all, it concerns effects stipulated by interdependence of micro-level and macro level of plastic deformation processes. Also, with the computing mechanics, instead of constitutive relationships, the adequate computer models can be used. Broad possibilities for computer simulation of various processes are opened by cellular automata approach. By means of numerical experiments, the cellular automata allows to study the macro behavior of the whole ensemble of cells depending on the local microscopic laws that define evolution of each cell and its interaction with the closest environment.We propose a mathematical model of a polycrystalline aggregate (the cellular model) based on a self-consistent scheme and on the interaction law similar to the one by Berveiller and Zaoui [1]. Our original solution is the self-similar structure of cellular automata that allows modeling of the fractal nature of real materials (Figure 1). The goals of this work are to present the major structures and relations of cellular model of polycrystal and to test this model for its adequacy as for describing known effects and dependencies. Identification of the model and its application for studying of concrete polycrystals are put aside for the future research."

Jan 1, 2001

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988