Search Documents

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By M. H. Lin, S. Kou

"Czochralski pulling has been a very widely used process for growing single crystals for electronic and optical applications. Dopant segregation can significantly degrade the quality and yield of single crystals. We have used the floating-crucible technique for segregation control in Czochralski pulling, our floating crucibles being unique in that the melt passageway is very long. As such, dopant back diffusion is suppressed, even when the cross-section of the melt passageway has to be relatively large to help the melt go through or when the pulling rate is very low. Single crystals of model materials K-doped NaN03 and Pb-doped Sn have been grown with very uniform dopant concentrations. IntroductionSingle crystals of electronic and optical materials are often doped with a small amount of impurities to develop required physical properties, e.g., P and B in Si for n-type and p-type semiconductors, respectively, and Nd in YAG lasers. Dopant segregation can result in nonuniform physical properties, thus degrading the quality and yield of the resultant crystals.Figure 1 is an illustration of the conventional Czochralski process for crystal growth. Several techniques have been developed to control dopant segregation in Czochralski pulling, including the push-pull technique (1,2), the drop-pull technique (3-7) and the floating-crucible technique (8-13). The first two techniques require precise sensing devices and feedback control systems to keep the feeding rate equal to the pulling rate. The last technique is simple since the feeding rate is automatically equal to the pulling rate."

Jan 1, 1994

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By Rita C. L. B. Rodrigues, Esperidiana A. B. Moura, Gisele D. Lazo, Renata D. S. Coiado, Rene R. Oliveira

Agricultural residues, which are produced with large quantities annually throughout the world, may be used as reinforcement plastic to replace the wood and produce particleboard for application in the development of low cost construction elements and reduced environmental impact. The main aims of this study was to investigate the effects of agricultural wastes and glass residues addition on the properties of recycled-HDPE/EVA blend for use in particleboard manufacture. The recycled-HDPE/EVA blend reinforced with corncob fiber (15 wt%), coffee parchment (15 wt%) and glass residues (1 wt%) were processed by melt extrusion, using a twin screw extruder and injection molding machine to obtain specimen test samples. The samples were characterized by mechanical test, XRD, TG, DSC, and FE-SEM analysis to understand the nature of interaction between the fillers reinforcement and recycled-HDPE/EVA blend matrix and their properties were discussed.

Mar 1, 2017

By Selvin Yesilay, Guray Kaya, Bekir Karasu, Asli Cakir

"In this investigation, the wastes of Eti Maden Kirka Boron Company of Turkiye were evaluated in the production of diopside and anorthite-based glass-ceramic glazes suitable for porcelain tiles fast and single-fired under industrial conditions. First of all, high wear resistant frits were produced with the use of concentrator and derivative borax wastes. Second of all, pre-engobed porcelain tile bodies were coated with the standard and newly produced frit-based glazes and industrial fast single-firing was employed. Final products were undergone to the certain standard tests to determine their Vickers hardness, wear resistance, thermal expansion coefficient values, gloss and coloring parameters. The micro-structures and phase formations of the fired glazes were also studied. Consequently, it was confirmed that the utilization of borax solid wastes in fast single-fired porcelain tile glass-ceramic glazes is possible. Introduction Porcelain tiles were introduced at the end of 1980s by Friandre, one of the leading Italian porcelain manufacturers. The American National Standard Specifications for Ceramic Tile defines porcelain tiles as: dense, smooth, impervious (with water absorption value less than 0.5 %) and stain resistant [1]. The excellent technical performances for ceramic tiles, such as mechanical, wear, frost and chemical resistance that make their use possible in indoor and outdoor building applications [2-3]. In the last decade, the growth rate of the global production of porcelain tiles increased more than those of other ceramic products; in fact, the technical properties of porcelain tile, coupled with even more improved aesthetic appearance, gave it a prominent role on the tile market [2]. Glass-ceramics are composed materials of one or more crystalline phases immersed in a residual glassy phase [4-5]. Glass-ceramic technology is based on controlled nucleation and crystallization of bulk glass [6]. The concepts of controlled crystallization of glass designate the separation of a crystalline phase from the parent glass in the form of tiny crystals. Their growth rate and final size are controlled by a suitable heat treatment [7]."

Jan 1, 2008

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By Wenjie Zhu

Hexavalent chromium is a widespread environmental contaminant. An Achromobacter sp. strain nominated Ch1 can reduce soluble and toxic chromate to insoluble and non toxic Cr(III) in aerobic cultures, and no Cr(VI) decrease was observed in anaerobic cultures. In contrast with other Cr(VI) reducing microorganisms, Ch1 showed higher Cr(VI) reduction at high pH. Reduction performed under alkaline conditions at pH 7 to 11, and the optimal pH was 10. During the reduction, pH decrease was observed may caused by production of acidic metabolic byproducts from aerobic respiration. In the present study, the ability of Achromobacter sp. Ch1 to reduce Cr(VI) during growth was evaluated with lactate as an electron donor. In NB medium, Ch1 reduced 100% of 24mM of Cr(VI) in 35h, but only 73% of 30mM of Cr(VI) after 48h of inoculation. Reduction was inhibited by metal ions like Ag+, Cu2+, Zn2+, slightly inhibited by Mn2+, and not affected by Mg2+. Results revealed that reduction rate of Cr(VI) also increased with the increasing of concentrations of lactate, and complete reduction was achieved at the concentrations above 40 mM. HPLC analysis demonstrated Cr(VI) reduction was associated with the consumption of lactate. There was a large quantity of dark blue sediment generated in the culture during Cr(VI) reduction by Ch1. Energy dispersive X-ray (EDX) analysis showed that the major element composed the formed sediment was chromium presented as Cr(OH)3 precipitate. The features characterizing Cr(VI) reduction by Achromobacter sp. Ch1 are high Cr(VI) concentrations and high pH.

Jan 1, 2006

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By Tian Tang, Sergio D. Felicelli

"The laser cladding is an important surface treatment for enhancing resistance against corrosion, abrasion, and wear. The focus of the present study is to develop a three dimensional finite element model to analyze the temperature history and thermal stress evolution during multi-pass laser cladding process on H13-H13 tool steel sample. A sequentially coupled thermal-stress analysis methodology was adopted in this study. The thermal model was firstly established to investigate the temperature history of the laser cladding process. Then the temperature history was used as input to mechanical model to calculate the thermal stress evolution during the process and the residual stress after the sample completely cooled down to room temperature. The influences of process parameters including the scanning speed and scanning strategies on temperature history, thermal stress evolution, and residual stress were investigated in details.IntroductionLaser cladding is an advanced material process technique, which is often used to improve mechanical properties or increase corrosion resistance, repair worn out parts, and fabricate metal matrix composites. In this process, the injected powder or wire feedstock material and a thin layer of substrate are melted and consolidated by use of a laser in order to coat part of a substrate or fabricate a near-net shape part.Numerous mathematical models have been established for analyzing the effects of process parameters, microstructure evolution, and thermo-mechanical behavior of laser cladding. Zhou et al. [1] established an analytical model to investigate the laser induction hybrid rapid cladding for Ni-based WC composite coatings. Huang et al. [2] also developed an analytical model to theoretically investigate the interaction between the laser beam and the powder stream of laser cladding process. A simple and realistic model of laser cladding was proposed by Picasso et al. [3]. The cladding layer is very sensitive to cracks due to the accumulation of residual stress, caused by non-uniform temperature changes, which have limited the wide application of laser cladding technique in industry. Recently, fmite element method has been increasingly used to simulate the laser cladding process [ 4-6]."

Jan 1, 2014

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By Shinya Otsuka

Activity coefficient of oxygen in sulfide-rich and metal-rich melts in copper-sulfur binary were determined at 1423 and 1523 K by means of a modified coulometric titration technique using the following cell: 0 ( is Cu-S melts) I Zr02 (+Ca0) I air, Pt The activity coefficient values obtained in the present study increase rapidly with sulfur composition in the vicinity of xs = 0.3333. The data obtained for the matte saturated with the metal-rich melts are in good agreement with those obtained by Kuxmann and Benecke, Schmied 1, and Eguchi and Yazawa. Those obtained for the metal-rich melts are in good agreement with the results of Sano and Sakao.

Jan 1, 1983

By Robert W. Bartlett

Biooxidation of an ore heap containing only a few percent of sulfide minerals requires insertion of a very large amount of oxygen either by natural air convection, forced air ventilation or gaseous diffusion. While shallow heaps, those with lateral distances much greater than their height, are of great interest for many heaped ore processing operations, natural convection is often ineffective for oxidizing them because of inadequate lateral flow into the heap's interior. Oxygen can diffuse into a shallow heap from its upper, horizontal surface in contact with air. Oxygen diffuses through the air-filled void space within the heap, driven by the oxygen concentration gradient resulting from internal oxygen depletion caused by mineral oxidation. Oxygen diffusion, coupled with the chemical reaction kinetics oxidizing the sulfide minerals, is analyzed for conditions of rapid mineral oxidation kinetics, requiring small mineral grain sizes, and for typical ore heap biooxidation parameters. Practical limits on heap heights are presented for effective biooxidation of the sulfide minerals within times of interest for heap biooxidation of refractory sulfide gold ores, one to three years.

Jan 1, 1995

By William A. Fuchs

A study of carbonaceous ore at the Santa Fe mine (Corona Gold Inc.) shows that there is no quantitative relationship between organic carbon content and preg rob, although much of this material preg robs. However, there is a relation between K20 and preg rob. Preg rob generally occurs only in those samples with greater than 2% K20. X-ray diffraction and chemical . studies show that the critical factor is the illite content of mixed (possibly interstratified) illite-smectite. Apparently illite, at a certain threshold, "geo-activates" the carbon. The potential for easily monitoring preg rob using a gamma ray spectrometer is discussed.

Jan 1, 1990

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By D. M. Hausen

A refractory siliceous low-grade silver ore (265 g/t Ag) from a prospect in Sonora, Mexico was investigated mineralogically and metallurgically to evaluate extraction of the silver by conventional methods. Approximately half of the silver was recoverable, occurring as coarsely crystalline acanthite (70-300 Am) that was liberated in material crushed to minus 10 mesh. The remaining silver is refractory and occurs mostly as finely locked (-2 to 0.2 Am) acanthite in cherty quartz, and as minor amounts of finely disseminated stylotypite or freibergite in fluorite. The mineralogic data have thus served to explain the 50-60% recovery of silver by flotation and cyanidation.

Jan 1, 1991

By James C. Sever

"With the advent of high energy costs and increasing concern for the environment leading to the incorporation the C02 life cycle as a criteria for the material used in a finished product, it is beneficial to analyze the plant and the process used in producing a raw material in order to identify practical, economic energy recovery opportunities. To this end a study was made of the proposed Nevada Clean Magnesium, Inc. Tami-Mosi reduction facility. Each source of waste heat is listed together with the assessment for potential co generation or direct recovery. The overall impact on energy requirement and C02 generation is provided.IntroductionHistorically metal reduction plants, large consumers of energy, do not recover waste heat. This occurred for many reasons:• Energy costs were low and the capital for a co-generation system could not be justified;• Waste heat sources contained entrained solids or liquids which would inhibit efficient energy recovery;• The exit temperature for the heat source was too low for efficient use by aaqueous Rankine cycle system.The business environment has now changed adding impetus to the recovery of energy previously discarded. Power costs have greatly increased. Global warming and the impact of carbon dioxide on the environment has become an issue which could impact the permitting of a plant. Technology improvements especially the development of a scaling environment waste heat boiler [l] and the development of the organic cycle Rankine cycle recovery system enable up to 70% energy recovery from ""low grade"" heat sources [2].With the inception of Nevada Clean Magnesium, Inc. 's (formerly Molycor Gold Corporation, Inc.)Northern Nevada Tami-Mosi project [3], an opportunity was presented to incorporate energy optimization from the initial design phase."

Jan 1, 2013