Search Documents

By G. Riverin, C. Simard, W. D. Stevens

"An on-line technique to measure the efficiency of decoating I delacquering processes is being developed by Alcan' s Arvida R & D Centre. Decoating processes are used to remove moisture and coatings from shredded coated material such as Used Beverage Containers (UBC) before melting. Complete removal has been demonstrated to maximize metal recovery. Quantifying the weight of carbon and organic residue adhering to the shred surfaces is very difficult to measure directly, as the material can be highly folded. The technique developed indirectly measures the residue remaining by analysing the concentration of CO evolved in the decoater end zone exhaust gas.A commercial CEMS (Continuous Emission Monitoring System) incorporating an infrared type CO gas analyser was modified for on-line process exhaust gas analysis. Both pilot and plant trials had demonstrated that the CO concentration measured was inversely proportional to the efficiency of the organic removal achieved. As the quality of coated purchased scrap can be highly variable in moisture and organic content, continuous measurement should permit adjusting the feed rate and other decoater process parameters to the quality of decoating required."

Jan 1, 2000

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Tang Mo-tang

A new process for extracting indium from indium-zinc concentrates was proposed in this paper. The process can directly extract indium from removed copper solution by P204, and cancel the stage of removing iron in the traditional process because of using iron and part of zinc in the In-Zn concentrates for direct preparing high quality Mn-Zn soft magnetic ferrites. The technologies in the processes, such as leaching the neutral leached residues with high concentrated acid at high temperature, reduction ferric and removing copper, and extracting indium, were investigated. The results showed that total recovery ratio of indium has been increased from less than 70% in the traditional process to more than 95%. This process has the advantages of largely simplifying the procedure of indium extraction, zero draining off of iron residue and zero emitting of SO2. So this is a clean production process.

Jan 1, 2006

By Ting Luo, Hongmin Zhu, Kai Huang, Shuanglong Du, Tao Gui, Yifan Xiu

"Poplar cotton, a cellulosic material, was found to adsorb metals ions effectively. In the present study, the biosorption characteristics of Pb(II) onto poplar cotton, were evaluated as a function of pH, contact time, biomass dosage, initial concentration and temperature. Within the pH range investigated (1.0-6.0), the optimal pH value suitable for the uptake of Pb(II) was determined. The maximum adsorption capacity obtained from the Langmuir model is around 0.52mol kg for the poplar cotton sorbent. Equilibration is achieved in 60min for the studied concentrations. Results suggest that the poplar cotton can be directly used as an effective and low-cost biosorbent for removal of Pb(II) from aqueous solution.IntroductionHigh value utilization of various biowastes produced in agricultural, forestry, fishing industries, etc. have attracted great interest from many researchers [1], Biomass, due to its easy availability, great abundance, low cost, easy processing, eco-friendliness and biodegradability, has exhibited exciting potential for being used as raw materials for the preparation of many new hi-tech functional products [2]. For example, using biowastes to synthesize sorbents for application in the removal of toxic substances such as dyes [3], heavy metals from the waste water [4] or in the recovery of valuable metals [5] from the ore tailings and secondary metals resources has made great progress in last decade. In present study, poplar cotton, a kind of white light fluff of poplar trees, like that of dandelion, usually flying in the air each spring was tested as a biosorbent for the remove lead ions from the water. It may also provide some good ideas for new sorbent design. Lead, as one of the typical poisonous heavy metals, for its typical toxicity and extensive pollution, was chosen to test the adsorption behavior of poplar cotton in aqueous solutions."

Jan 1, 2012

By Gen Kamimura, Hiroyuki Matsuura

Zinc is widely used for galvanization of steel plates due to its high corrosion resistance. Steel scraps containing waste zinc-coated steel plates are remelted for recycling of steel in electric arc furnace (EAF) process, in which zinc is concentrated in EAF dust ranging from 10 to 40 mass%. Therefore, recycling of zinc from EAF dust is important to secure zinc resource. Our group has proposed selective chlorination and evaporation method recovering zinc as a form of chloride from EAF dust. Since recovered zinc chloride may contain lead, iron and copper as impurities, purification of zinc chloride is essential for production of highly pure metallic zinc. In the present study, removal of lead chloride from molten zinc chloride-alkali chloride by cementation reaction adding zinc was investigated. Experimental results were analyzed and discussed thermodynamically and kinetically as well as the feasibility and limitation of this process were examined.

Mar 1, 2018

By Marcos V. F. Fonseca, Gilson V. Fernandes, Caroline G. de Oliveira, Sergio N. Monteiro, Frederico M. Margem, Anna C. C. Neves

Natural fibers represent an economic and environmental motivation for replacing the synthetic fibers, mainly as composite reinforcement material, which is one of their major applications. Some advantages of the natural fibers are the biodegradability, low cost and renewability. Among the natural fibers, the lignocellulosic ones are highlighted for their high resistance. One of the most cultivated lignocellulosic fibers in Brazil is the Eucalyptus fiber, extracted from the bark of Eucalyptus citriodora plant. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volume fractions of Eucalyptus fibers. The specimens were made by pouring the still liquid resin into the mold and laying the fibers onto the resin. The results show a decrease in the tensile resistance with the increase of volume fraction. It is due to the low adhesion between the fibers and the matrix.

Mar 1, 2017

By J. W. Perez

In the treatment of process effluents containing metal ions, it is sometimes desired to remove all of the heave metal ions while at other time it is, desired to remove one heavy metal ion from another, selectively. Ion and precipitate flotation processes were evaluated to perform these functions using the copper-iron aqueous system as a model. Because preliminary foam fractionation experiments proved to be relatively inefficient, most of this work has focused on precipitate flotation using both hydroxide and sulfide precipitation. Test results indicate that by proper control of reagents and operating conditions, it is possible to substantially reduce the froth volume over that achieved with foam fractionation and to separate copper from iron selectively. Mechanisms for collector attachment to precipitates were studied.

Jan 1, 1992

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In recent years, a new process of “direct reduction-electric furnace smelting separation” has been put forward and developed for recovering the iron, vanadium, titanium and chromium to make full use of the chromium-bearing vanadium titanium magnetite. In the present work, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the migration of Fe, V, Cr and Ti with different nC/nO (mole ratio of carbon and oxygen). The calculation results indicate that the recoveries of Fe, V and Cr increase with increasing nC/nO and temperature respectively. In addition, the recoveries of Fe, V and Cr are up to 90% when the nC/nO value is more than 1.15.

Mar 1, 2018

By L. Cifuentes

Electrodialysis (ED), i.e. a technique based on the effects of electrically charged membranes on ions in solution in an electric field, has been applied to Cu-Fe-As-Sb- H2SO4 electrolytes similar to those used in copper electrorefining and electrowinning operations. The effects of current density, time and species concentration have been studied in a batch ED cell. The technique has shown to be effective in concentrating and separating a range of ions and points to possible new methods of treating copper electrometallurgy effluents.

Jan 1, 1999

By B. J. Zhao, F. L. Han, L. E. Wu, M. Chen, Y. H. Chen

Magnesium is the lightest structural metal with a density only two-thirds of aluminium and one-quarter of steel. It can be produced by electrolysis of fused magnesium chloride or high temperature reduction of the oxide. The predominant method for magnesium production is the Pidgeon process which is a batch process starting from calcined dolomite and ferrosilicon. CaF2 is commonly used in the process as the catalyst. Analyses of the slag samples and thermodynamic calculations indicated that liquid phase plays important role in the reduction process. Effects of chemistry, temperature and gas pressure on the production have been discussed and compared with the operating data. Understanding of the reaction mechanisms will provide a fundamental base for alternative processes of the magnesium production.

Mar 1, 2017

By Henrik Gudbrandsen, Geir Martin Haarberg, Ana Maria Martinez, Karen S. Osen, Sverre Rolseth

"The Several approaches were tried for developing an electrochemical route for producing high purity silicon from molten salts. K2SiF6 and metallurgical grade silicon were used as the source of silicon. Molten LiF-KF and pure KF with additions of K2SiF6 were used as electrolytes at temperatures from 550 - 900 oC. Silicon was cathodically deposited and anodically dissolved in the fluoride electrolytes. High electrorefining efficiency was obtained for many elements after electrolysis experiments at constant potential or constant current. The main challenge was to reduce the contents of boron and phosphorus. Another difficulty was to remove inclusions of solidified electrolyte. The lowest energy consumption was estimated to be ~ 3 kWh/kg Si, while the best current efficiency for Si deposition was found to be ~ 95 %.IntroductionSilicon is the most important material for photovoltaic power generation devices because of high feasible efficiency, low ecological impact and slow degradation. Development of a new and less expensive route for producing silicon of the desired quality is necessary in order to make solar cells competitive. Electrochemical routes may be an alternative possibility, and many laboratory studies have been reported over the past few decades. Most of the studies have been performed in molten salts, chloride or fluoride, at moderate temperatures so that solid silicon was deposited at the cathode. The production of high purity silicon has shown an annual increase of about 25 %, due to the increasing demand of solar grade silicon (SoG-Si). For future increased use of solar energy it is important to develop alternative, more energy efficient and cheaper processes for SoG-Si production compared to the Siemens process.Common silicon sources have been SiO2 and K2SiF6 for electrowinning and MG-Si in the case of electrorefining. A serious challenge is to find an oxygen evolving anode for electrolytes containing dissolved oxides. Especially at moderate to high temperatures and in molten fluoride electrolytes this is a difficult task.Many experimental results have been reported in molten chloride electrolytes. Nohira et al. [1-3] and Chen et al. [4] cathodically deposited silicon by electrodeoxidation of solid SiO2 in molten CaCl2 by potentiostatic electrolysis. An alternatice approach is to use electrorefining of low-cost metallurgical grade silicon (MGSi) to produce SOG-Si. In previous studies [5], an MG-Si anode was used, and silicon was successfully electrodeposited on a molybdenum wire in a CaCl2 based melt. It was found that the anode was strongly passivated due to the precipitation of silicon. Also, some deposits detached from the molybdenum wire because of the poor adherence to the cathode.Considering the Cu-Si alloy which has a good segregation effect for some impurities, and should not passivate, could be a good candidate anode for electrorefining. [6]."

Jan 1, 2014

By J. L. Delplancke

During copper electrowinning in sulphate electrolyte, intense oxygen evolution takes place at the anode. Lead alloy anodes are progressively replaced by dimensionally stable anodes in order to avoid the cathode contamination by dissolved lead. The electroactive coating of these anodes has to be as cheap as possible, adherent to the substrate, electrochemically stable and has to be efficient at high current density and high temperature. This requirement is even demanding in case of copper electrodeposition for the production of thin copper foils for the electronic industry. The production of thin (20 µm thick) copper foils for the printed circuit boards requires high purity copper electrodeposited at a current density as high as 7,000 A/m2. The choice of a long term coating composition is driven by economics. The purpose of this paper is mainly to review the anode compositions suitable for copper electrowinning and for copper electrodeposition at high current density. A short description of preliminary results obtained with a new anode coating on a titanium substrate is also presented.

Jan 1, 1999

By John G. Reid

When the paper "Operations at the Greenvale Nickel Project Mine and Refinery" was delivered at the 1st International Laterite Symposium in February 1979, the Yabulu Caron plant had been operating for four years and production had just stabilized. The design had been based closely on the Caron plant at Nicaro, Cuba, built in 1944, also by Freeport. Yabulu had 10 Herreshoff ore roasters and production in 1978 was 18,682 tonne nickel as impure oxide sinter and 763 tonne cobalt in a mixed sulphide with a cobalt to nickel ratio of 1 :2.5. In the 25 years since the 1st Symposium, two more roasters have been added, but dry ore processing rate has remained relatively unchanged at 2.4M Uyr to allow a lower feed rate per roaster with associated higher recovery. The ore source has changed from the domestic Greenvale mine to imports from New Caledonia, Indonesia and the Philippines. Nickel production between 1978 and 2003 has risen by 67%, cobalt has risen by 146% and the products have changed to high purity nickel compacts and "ChemGrade" cobalt salt. The plant changes that have contributed to the increased recovery, production and product value are discussed. Keywords: Caron, Yabulu, nickel, cobalt, ammonia

Jan 1, 2004

By B. W. Lightfoot, Neill F. Arthur

"The AusIron process is a new development of the well established Ausmelt bath smelting technology(l). The development of this technology has been tied to the South Australian Steel and Energy (SASE) project which brings dedicated coal and iron resources together with this new technology. SASE is a joint venture between Ausmelt (40%), Meekathara Minerals (40%) and the South Australian Government through Mines and Energy South Australia (MESA) (20%). It will use a multiple lance furnace to process iron ore using steaming coal for both fuel and reductant.It is intended to build the simplest plant economically possible. Refinements such as preheating and prereduction of the ore are compatible with the technology but are not expected to be necessary in the first generation plant.The joint venture is negotiating with suitable partners for funding of the project through to commercial implementation at a target scale of2.5 mt/a of pig iron.ObjectivesAusIron aims to produce pig iron directly from steaming coal and from any of a variety of iron sources in a simple furnace system with a minimum of pre-processing of either coal or iron ore. Preheating and prereduction of ore are compatible with the technology but may not be necessary. The immediate aim is not to be the technology that uses the least quantity of coal to produce iron metal but rather the technology that uses the least number of dollars to produce metal.The chemistry of iron making is well known, probably better known than that of smelting of any other metal. Iron has been made for thousands of years and it is possible to make iron from charcoal and ore in a simple blast furnace the size of a beer barrel. The focus is therefore not making iron but rather making it more cheaply than it is made by current technologies. Large blast furnaces now set the standard and new technologies must perform better if they are to gain market share. It is still the cost of iron, energy units and capital going into these mega blast furnaces which ultimately set the market price for pig iron."

Jan 1, 1996

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Victoria Vaccarezza, Corby Anderson

Due to the demand for rare earth elements for everyday technology and applications, there has been much research initiation into the extraction and recovery of rare earth elements. An otherwise unknown mineral, eudialyte is a zircon silicate consisting of rare earth oxides, specifically the heavy REO yttrium (III), with only trace amounts of thorium and uranium. The first part of this project aimed at finding an efficient way to liberate and upgrade eudialyte to concentrate the REO content. A combination of gravity and magnetic separation techniques were employed, resulting in limited success. The second part looked at the hydrometallurgical processing of eudialyte through various leaching experiments with sulfuric acid. In all, this project will discuss why certain processes were utilized over others, as well as the difficulties that arose during processing.

Mar 1, 2018

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012