Search Documents

By Shigeru Ueda, Shin-ya Kitamura, Shohei Koizumi, Xu Gao

Steelmaking slag was confirmed to be a useful fertilizer for paddy growth as it efficiently supplies Ca and Si to soil water. In addition, supplement of Fe from slag fertilizer has been expected to suppress the H2S generation in paddy soil, especially for the degraded paddy soil. However, on the basis of our previous research, the Fe dissolution ability changed with slag brands, and even some brands could dissolve Fe under paddy soil pH, the supplying ability were not high. To improve Fe dissolution, we found that among various kinds of Fe-rich mineralogical phases in slag, the CaO–SiO2–FeO glassy phase showed highest water solubility of Fe. Because the CaO–SiO2–FeO glassy phase was a quenched molten phase, its dissolution behavior may depend on chemical composition, and this is important for controlling slag composition to produce fertilizer which can easily release Fe. Therefore, in this research, the CaO–SiO2–FeO glassy phase of various CaO/SiO2 ratio, Fe2+/T–Fe ratios, and FeO contents were synthesized, and the dissolution behaviors of Fe as well as other cations from these synthetic glassy phases into an aqueous solution at pH of 5 were investigated. The result showed that the dissolution ratio of Fe increased significantly by increasing Fe2+/T–Fe ratio. An increase in FeO content of glassy phase also increased the dissolution of Fe. In addition, the Fe dissolution ratio showed a local maximum with increasing CaO/SiO2 ratio.

Mar 1, 2017

By C. Hakan Gür

Optimization and control of the microstructure is important for improving the properties of steel components. Development of non-destructive techniques for microstructure characterization is a critical task. Magnetic Barkhausen Noise (MBN) technique is a promising and challenging non-destructive technique fo automated evaluation of microstructures in steel components in a fast and reliable manner. This paper presents the results of MBN measurements for microstructure characterization of the quenched and tempered steels.

Mar 1, 2017

By Tiejun Chun, Gutian Mu, Jiaxin Li, Hongming Long, Zhengwei Yu, Ning Li

The basic characteristics of iron ore, including assimilation, fluidity, cohesive phase strength and the ability to produce calcium ferrite, are often used to evaluate the sintering properties of iron ore and guide the optimization of iron ore blending. Six kinds of common iron ore used in a steel company in China were selected in this work. The basic characteristics of the single iron ore and blended iron ores were studied, as well as the difference between weighted averages of basic characteristic index of single iron ores and the real value of basic characteristic index of blended iron ore under different ore blending ratios. The results shew that the liquid phase liquidity, cohesive phase strength and calcium ferrite formation ability had a significant linear positive correlation with SiO2 content. The weighted average of basic characteristic index of single iron ore cannot fully reflect the actual blended iron ore properties. The optimization of the blending ratio can be achieved through the detection of the basic characteristics of the mixed iron ore, combined with the basic characteristics of iron ores.

Mar 1, 2018

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By M. W. Wadsley

Despite the convenient subdivision of extractive metallurgy into hydro- and pyro- divisions, many flowsheets contain both types of process. When complex materials are used as feed, combinations of hydro- and pyro-metallurgical processes are even more common. Hydrometallurgy is used to treat many by-products and waste-products. (Bio-metallurgical processes may be considered to be a sub-set of hydro-metallurgical processes.) Combinations of the different processes in the Australian metallurgical industry are described. Selected international examples demonstrate that the use of combked processes is not a unique. Antipodean phenomenon. The motives for selection of combined pyre- and hydro-metallurgical processes in a flowsheet are examined.

Jan 1, 1994

By HeeDong Lee, Owen Reedy, Lawrence Matson, Naidu Seetala, Thomas Key

Spark Plasma Sintering (SPS) consolidated ZrB2+SiC composites using nano-powders (around 40 nm) showed smaller grains compared to those using micron size powders and segregation of SiC into islands is minimal but with higher oxidation of ZrB2 to form ZrO2 in nano-composites. Argon-gas purging prior to SPS consolidation at around 2000 °C and 40 MPa of ZrB2+20vol.%SiC nano-powders was used to minimize the oxidation and obtain fine granules with high densification. The densification of the Argon-gas purged nano-composites is higher compared to those consolidated without Argon gas purging. The EDX analysis showed a strong reduction in the oxygen peak for the Argon gas purged composites. The XRD spectra also support this observation with less ZrO2 phase composition in Argon gas purged composites. The Vickers micro-hardness showed slightly lower values for Argon gas purged composites though they have higher densification.

Mar 1, 2017

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By V. Ramachandran

The Amarillo Copper Refinery, the newest and most modern copper refinery in the world, has been in operation for the last eleven years and has a rated capacity of 460,000 st/yr. The tankhouse - a structure that covers 500,000 ft2 under one roof - extends one-half mile in length and is a model of materials-handling efficiency. The use of recently developed and patented* reagent control technology, termed "Reatrol Process", has increased current efficiencies to an average of 98% and has considerably improved the physical and chemical quality of the cathode deposit. The present paper describes the current operations at the Amarillo Copper Plant with special emphasis on tankhouse operation.

Jan 1, 1987

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By D. Ducharme, J. Lenz

Operation of the Kidd electrolytic zinc plant commenced in 1972 with a cellhouse capacity of 105,000 tonnes of zinc cathode. The original cellhouse layout consisted of 42 parallel rows for a total of 588 cells. As leaching capacity increased, the cellhouse was expanded to 630 cells. Zinc cathode was manually stripped from plant start-up until the development of a mobile automated stripping system in 1994. Machine development continued until a second unit was placed in production in 1996, from which point, 60 % of the cellhouse was being stripped with the automated system. The final phase of the project was implemented in 1999 with the commissioning of two more automated strippers. This paper describes the implementation of the automated stripping system and its impact on cellhouse productivity.

Jan 1, 2000

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By Wangzhi Zhou, Huasheng Chen, Bowen Li, Meng Liu, Mingsheng He, Long Zou

Steel slag is an inevitable by-product from a steelmaking furnace such as a converter, an open-hearth furnace or an electric arc furnace. The yield of steel slag increases with the sharp rise of steel production. Utilizing the slag effectively and comprehensively is one of the important tasks to promote the development of iron and steel industry in China in a sustainable and efficient way. In this study, hot-poured steel slag from a converter was used to prepare ceramics by mixing with fly ash, microsilica, and quartz. After heating at 1100–1200 °C, the ceramics were well sintered. XRD revealed that multiple crystalline phases coexisted in the glass-ceramics, and the main crystalline phases were diopside and anorthite. SEM observation indicated that there was a plate-columnar composite structure in the ceramics. Reaction mechanisms were discussed.

Mar 1, 2018

By E. A. Werner, W. Liebfahrt, J. Blaha

"The influence of the composition and the microstructure on the plane strain fracture toughness of five cold work tool steels all processed via the powder metallurgical route is investigated using 3-point bending specimens. The steels differ in composition and therefore possess different volume fractions of carbides. The amount, size and distribution of the carbides in the matrix are estimated by quantitative image analysis on a plane parallel to the fracture surface without discrimination of the carbide type, since the carbides are always much harder [1,2] than the matrix, irrespective of their composition. Due to the production of the steels via the powder metallurgical route almost all carbides are spherical in shape. The mechanical in-situ properties of the matrix are characterized by indentation tests performed with an ""UltraMicro"" -indenter in a scanning electron microscope.IntroductionCold work tool steels are used as tools in applications where excellent wear resistance and high hardness are required. Examples are cutting, woodworking, thread rolling, wire and deep drawing, cold extrusion and pressing of parts at process temperatures below 200°C. For such applications the steels must show an optimum combination of hardness, wear resistance and toughness while offering good machinability. Hardness and wear resistance are controlled by the amount of carbon and carbide forming elements such as molybdenum, tungsten, vanadium, chromium and niobium. These elements are present in the MC-, M6C and M7C3-carbides and are also responsible for the precepitation of secondary carbides during tempering. In this report attention is paid to the influence of the primary carbides only, while the very small ~~nm) secondary carbides will be treated as constituent of the homogeneous matrix. Increasing the amount of carbides (alloying elements) usually results in a decrease of the material's toughness which is caused by the presence of clusters and/or bands of carbides. To achieve an optimum combination of hardness, wear resistance and toughness many of the today's cold work tool steels are processed via the powder metallurgical (PM) route, which helps to prevent non-uniform element/carbide distribution because of the rapid solidification of the powders used. The resulting microstructure of the tool steel then consists of a tough matrix with uniformly distributed hard carbides· of globular shape. This shape of the carbides is also desirable instead of blocky carbides present in non-PM tool steels, since they improve the machinability of the steel. An additional advantage of PM-steels lies in the possibility to produce near net shaped tools thus lowering the costs of machining."

Jan 1, 2000

By Katsunori Yamaguchi

Secondary materials, that contain relatively high concentrations of platinum group metals, (PGMs) are treated in copper smelting process. The PGMs lost in the slag is increasing with increasing quantities of scrap treated amount. To determine the portion of the PGMs chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. An experimental study was carried out to determine the distribution of palladium between the FeOx–SiO2 slag and the liquid Cu2S–FeS matte at 1573 K and a fixed partial pressure of SO2 of 0.1 atm. It was found that the distribution ratios are around 10−3 for platinum and palladium. The distribution ratios show a tendency to increase when the grade of matte is increased above 60 mass% Cu. In addition, the solubility of platinum in FeOx–SiO2 slag equilibrated with a pure palladium and the Pd-Cu alloy was determined at 1573 K and the range of oxygen partial pressure from 10−9 to 10−7 atm. The solubility of palladium in the slag tends to increase with increasing oxygen partial pressure and activity of CuO0.5 in the slag.

By Marcelo Mourao, Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano

"The self-reduction is an alternative and promising process for production of pig iron because offers decisive benefits such as enhancing the reaction kinetic with decrease in fuel consumption and C02 emissions. The self-reduction mixture of iron ore fines, carbonaceous reducer and additives for slag forming components, without agglomeration, was tested in a laboratory rotary kiln. The additives for slag were defined for presenting two different estimated liquidus temperatures (1623 Kand 1773 K) to verify the effect of these temperatures on the iron-carbon nuggets coalescence process. These mixtures were tested at 1673 and 1773 Kin an experimental rotary kiln. After reduction-melting and coalescence processes the samples were disaggregated and the iron nuggets were classified by size. It was considered that nuggets larger than 7,93mm would be a good reference for coalescence index. Low liquidus temperature slag presented 37% of this larger fraction against only 13.5% for high liquidus temperature one. The low liquidus temperature slag would facilitate contact between the particles of iron-carbon in a rotary kiln, enhancing the coalescence.IntroductionThe slag composition usually depends on the reducer ash composition, the ore gangue, the binder composition and any fluxing material [l], and the mechanism of carbon transportation in slag that contains iron oxide reducible by carbon can be explained by the oxide reduction and the metal carburization. During carbon transportation, the carburized particle is transported to slag-metal interphases by the gravity effect, being assimilated by the metallic phase [2]. When the slag's iron oxide comes in contact with the solid carbon, it is immediately reduced, forming Fe particles and CO bubbles as it is shown in the figure l(a). The Fe particles are carburized by carbon particles; they are liquefied simultaneously in the carbon-slag interphase. The Fe-C liquid particles are transported from the slag-carbon interphase to iron-slag interphase as a result of slag flow, based on the surface tension difference (Marangoni effect), figure l(b). The Fe-C liquid particles coalesce on the iron surface and the carbon is immediately diffused in the iron as it is shown in figure l(c). The reduced iron is carburized continuously by repeated sequences [3]."

Jan 1, 2013

By M. A. Kader, W. D. Hutchison, M. A. Islam, P. J. Hazell, J. P. Escobedo, A. D. Brown

The effects of post-foaming thermal processing on the quasi-static compressive strength of closed-cell aluminium foam with an average relative density of 0.56 g/cc have been investigated. Samples were subject to one of four material conditions: as-received (AR), warm aged (WA), solution treated (ST), and annealed (AT). X-ray diffraction (XRD) was performed to determine a relationship between each material condition and macro-crystallographic texture of the dendritic α-Al phase. It was found that all heat treated samples contained clear deviations from random texture towards the exterior regions of the samples, indicating non-uniform recrystallization kinetics. The ST and WA samples exhibited the highest yield stresses and energy absorption, with the AT samples exhibiting the lowest. Additionally, it was found that the AR and WA conditions lost 12.8 and 15.6% of their total mass from brittle cell wall crumbling, whereas the AT and ST conditions lost 2.5 and 3.0% of their total mass.

Mar 1, 2017

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By Yuzo Hiroshige, Kiyotaka Tahara, Hiroki Hatayama, Masaharu Motoshita, Tomohiko Akahori

Large amount of rare earth metals is stored in the used electric products. Hitachi has started to develop the environment-friendly process for rare earth metals recovery from used magnets. We report here the environmental impact of our process, in comparison with the conventional recycle process utilizing solvent extraction. As an evaluation method, Life-cycle Impact assessment Method based on Endpoint modeling ver.2 (LIME2) developed by the National Institute of Advanced Industrial Science and Technology (AIST) in Japan is applied. It was found that the environmental impact of the new process was more than that of the conventional process. For further reduction of its environmental impact, minimization of energy consumption to operate the equipment was most effective. Decreasing the amount of magnesium, used as an extractant, and the improvement of the extraction rate of rare earth metals were also considered as specific options for reducing energy consumption in the plant development.

Jan 1, 2014