Search Documents

By R. Padilla

The reaction of chalcopyrite with gaseous sulfur has been investigated in the range 350-450 °C in order to transform this mineral into a more acid soluble copper sulfide and insoluble iron sulfide. The results of thermodynamic analysis of this system as well as the X-ray diffraction analysis of the reaction products showed that in the temperature range 350 400°C the sulfidation reaction proceeded without formation of intermediate copper-iron sulfides according to: The effects of temperature and time on the conversion of chalcopyrite were studied. Conversion of chalcopyrite reached about 80% very rapidly with increase in temperature up to about 400°C. The recovery of copper from the sulfidized samples was determined by leaching in oxygenated 1.2M H2S04, 2M NaCI solution. Copper recoveries over 90 % were obtained from samples sulfidized for 30 min at temperatures lower than 400°C.

Jan 1, 2001

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011

By lonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the NilS2-FeS matte with either FeOx-CaO or FeOx-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

Adding CaO into the vanadium extraction converter is an effective way to decrease the dephosphorization burden in subsequent steelmaking process. The crystallisation process of spinel is one of the most decisive factors in the subsequent extraction. The theoretical calculation results show that the temperature of the peak total crystallization rate will decrease 5K with basicity increasing 0.1. The relation between cooling conditions and grain size of spinels is also discussed. It is found that low cooling rate and high basicity benefit spinel crystal growth. And the non-isothermal crystallization kinetics results indicated that the restriction factors of spinel growth is that solid crystals accept new components from liquid-solid interfacial. While the sample was cooled down to 1250 (1523K) at cooling rate of 5K/min, the crystal growth is consistent with Ostwald coarsening grew up law, and controlled by diffusion of particle.

Jan 1, 2016

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By Gordon D. Jarvinen

Polymer Filtration (PF) Is an innovative, selecthle metal removal technology. Chelating, water-soluble polymers are used to selectively bind the desired metal ions and ultrafiltration is used to concentrate the polymer-metal complex producing a permeate with low levels of the targeted metal ion. When applied to the treatment of, Industrial metal-bearing aqueous process streams, the permeate water can often be reused within the process and the metal ions reclaimed. This technology is applicable to many types of industrial aqueous streams with widely varying chemistries. Application of PF to 'aqueous streams from nuclear materials processing and electroplating operations will be described.

Jan 1, 1999

By Shufang Ding, Fukun Yan, Zhiqiang Shan, Wei Chen, Cuicui Ji

"To remove aluminum ion from chlorinated rare earth solution, this paper used hydrolysis method to explore the hydrolysis behavior of aluminum ion in aluminum chloride solution and confirm the optimum conditions of aluminum ion hydrolysis, which are pH value, temperature and initial concentration of Al203 and so on. The experimental results show that single treatment can make aluminum precipitation rates of chlorinated rare earth solution reach about 90% by hydrolysis precipitation; and then several recycle disposal can get precipitation rates of 89% for aluminum and 2.86% for rare earth.IntroductionIn China, rare earth resources are very rich and unique minerals, complete variety, and rare earth products are very large in the domestic reserves. Rare-earth and application products have been deep into all areas of our life, permanent magnet material of rare earth is one of the most popular application areas[11. Binary oxides such as praseodymium neodymium have been widely applied in the fields of glass, ceramics, magnetic materials, catalysts and so on. Especially, the advent of the Pr-Nd-Fe-B magnets which makes the world magnetic material into a new stage of development [2•3]With the development of science and technology, for industrial, physical and chemical indicators of raw materials Pr-Nd oxides (such as particle size, specific surface area and non rare earth impurities etc.) are also getting higher and higher. The oxide size has an important influence on sludge formation in the electrolytic process. If the size is too large, added oxides have settled on the bottom of slot before melting, and then generated sludge; if the particle is too small, it can cause dust dispersion, enlarge oxide unit consumption and increase the cost of production in the charging process. Some early processes use oxalic acid to make chloride neodymium praseodymium settle, and impurity can be removed cleanly, but the cost is high, it is not suitable for production. At present, most enterprises are using ammonium hydrogen carbonate to precipitate chlorinated neodymium praseodymium, but chlorinated neodymium praseodymium such as iron and aluminum and so on can easily form gel in the precipitation process, seriously affect the growth of neodymium praseodymium carbonate crystal and often leads to particle meticulous, even may also generate gel-like neodymium praseodymium sediments and cause centrifugal or suction filtration difficult. Now the actions and their removal of impurity such as iron and aluminum have done a lot of research in the production process of rare earth, removing aluminum craft with alkaline (sodium hydroxide) and acid (oxalic acid) has good effect, but the cost is higher[41; used adding complex agent to remove aluminum method which is simple and easy to operate, but aluminum removal rate is not high, and also changed the sediment of crystal type[51, and etc. This paper discusses the removal of chlorine from rare earth solution on the basis of the hydrolysis property differences betweenAJ3+ and rare earth ion."

Jan 1, 2013

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990's. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

By Thomas R. Wildeman

Experimental methods for studying vapors over solid minerals are reviewed and an especially developed method using atomic absorption is described. The method is used to study vapor pressures over Te. Ag, Au, Ag2Te, and AuTe2 from 250°C through 10S0oe. Vapor pressures observed and, concurrently. sintering properties are significantly altered by the form of the solid. The vapor pressures of the tellurium compounds reveal complex processes occurring on the surfaces of the solids. The data given also point out a method of recovering precious metals from their telluride minerals w

Jan 1, 1987

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By B. Zilbergleyt

Current understanding of chemical equilibrium is based exclusively on the probabilistic considerations that are correct for isolated systems with only one chemical reaction to take place. For the systems with multiple chemical interactions, current paradigm of chemical thermodynamics promotes the idea of openness, artificially flavored with coefficients of thermodynamic activity. Recently introduced thermodynamics of chemical systems and the Method of Chemical Dynamics (MCD) offer explicit accounting for the multiple chemical interactions within the system. In the new theory, thermodynamic equilibrium of the j-subsystem obeys the logistic equation derived exclusively from the currently recognized concepts of thermodynamics. Having the only one new parameter -the subsystem's reduced chaotic temperature 'tj to describe external interactions, and reaction extent Ilj as independent variable, this equation covers the whole domain of the system's possible states from true thermodynamic equilibrium through the open equilibrium to bifurcations and chaos depending on the 'tj value. The MCD brings new opportunities to thermodynamic simulation of complex metallurgical and chemical systems, allowing for the analysis of their domains of states and the area limits, and for more accurate calculation of the equilibrium compositions. Its usage is exemplified in this paper by several applications. Keywords: chemical thermodynamics, open systems. complex systems, chemical dynamics.

Jan 1, 2003

By Fathi Habashi

During the recovery of copper, nickel, zinc, and lead from their sulfide ores, large amounts of sulfur dioxide are generated. A fraction of this gas is captured and transformed into sulfuric acid and liquid SOl and the remainder is emitted to the atmosphere. Numerous proposals were made to solve this problem. Hydrometallurgy offers the only valid solution by which elemental sulfur instead of sulfur dioxide can be produced. Sulfur can be easily stored, transported long distances, or transformed into S02 and H2S04 when desired.

Jan 1, 1996

By Guo Xian Jian

In this paper, the effects of matte grade, flux grain size, blast flowrate and blast O2 content on the process of silica flux melting in a copper converter were investigated. The results showed that the blast flowrate and the blast 02 content were not significant factors in the melting process. However, with an increase in grain size of flux and grade of matte, the amount of the flux molten decreased. The data on the melt rate of process correspond well with the mathematical model which simulates the chemical reactions occurring at the interface. The kinetic equations of melting are as follow:

Jan 1, 1996

By D. J. Webb, D. G. Reynolds, D. W. Ashman, D. W. Goosen

Cominco Limited operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Central to the successful operation of this complex is the treatment of zinc leach residues through the lead smelter. In 1997, Cominco started up a new lead smelter using KTVCET flash smelting, a state-of-the-art conventional slag fuming furnace, and a new drossing plant. The smelter has fully met the requirements for environmental performance, reduced energy consumption, and lowered labour costs. This paper provides a description of the new smelter and discusses the problems encountered during the start-up, as well as the solutions to those problems. Recent operating results are presented. Lead-Zinc

Jan 1, 2000

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. In 1996, however, it successfully shifted to a single furnace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000