Search Documents

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By A. J. Wainwright

The Coffee Creek lode gold discoveries are located in the White Gold district (Dawson Range), west-central Yukon, 130 km south of Dawson City and 30 km south of the Golden Saddle gold deposit (Figure 1). Extensive structurally-controlled gold mineralization has been discovered during the 2010 and 2011 exploration drilling campaigns, highlighting this part of the Dawson Range as a significant emerging gold district. [ ] In this contribution we review the geological framework and describe the mineralization styles and metal signatures observed to date on the Coffee project. The main Coffee area is underlain by a 15 km by 4 km geochemical footprint, characterized by discrete linear gold-in-soil anomalies that correspond to various mineralized corridors. Of several mineralized areas tested in the past two drill seasons by diamond core and reverse-circulation (RC) drilling, we focus on the Supremo, Double Double, Latte and Kona zones; areas with the most information obtained from drilling thus far (Table 1; Figure 2).

Jan 1, 2012

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world's centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By Jeffrey A. Pontius

The Cresson gold deposit is in the southcentral portion of the Cripple Creek mining district in central Colorado (Fig. 1). The deposit is hosted by a series of 32 Ma (Kelley, 1995) felsic to mafic, alkaline volcanic rocks that were deposited in a diatremal environment. Mineralization in the Cresson deposit is structurally con-trolled. It occurs as disseminated and vein type. Gold deposition is closely associated with potassium-pyrite metasomatism and quartz-telluride vein development(Pontius, 1992). The Cresson deposit is owned by the Cripple Creek and Victor Gold Mining Co. (CC&V), a joint venture between Pikes Peak Mining (67%) and Golden CycleGold (33%).

Jan 1, 1996

By Carl G. Bock

INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has let a contract for the excavation of three rock stations, spaced about 3550' (1082m) apart, beneath Connecticut Avenue in Washington, D.C. Two previous rock stations have been completed, one of which had a crown pilot tunnel excavated to explore geologic conditions that would be encountered during the station excavation. This pilot tunnel was primarily for inspection by bidders and design was based on core hole information. The other rock station had no pilot tunnel and was also designed on the basis of core hole information. The three rock station areas, which are the subject of this paper, have been explored by crown pilot tunnels and an as-built report, with geologic maps and sections, has been prepared, for use by the design engineer as the basis of design for support of the structures. The geotechnical report describes the geologic structure in detail and relates it to excavation and support of the three crown pilot tunnels and the running tunnels which will be enlarged to create the 58'W x 44'H x 700'(+)L (17.6m x 13.3m x 212m +) stations. The information was complete enough to permit the design engineer to visualize the geologic structure and compute loads for the various types of rock conditions. It was therefore possible to determine the size and spacing of the steel sets for the several different conditions of rock structure encountered in the pilot tunnels.

Jan 1, 1976

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009