Search Documents

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By Yasutaka Izumi, Tuneyoshi Funasaki, Keizou Miki, Makoto Kanai

INTRODUCTION The Tokyo metropolitan region, inclusive of the three neighboring prefectures (Kanagawa, Chiba and Saitama), has the highest concentration of population and industry in Japan; with an area of 13,500 km2 or only 3.6 percent of the national land, but a population of 31.8 million or 26 percent of the national total, and a Gross Regional Product (GRP) of146 trillion yen (US$1.33 trillion) or 36 percent of the overall GDP of Japan as of 1990. Tokyo Bay, embraced by the metropolitan region as shown in Figure 1 (a), (b), is open to the Pacific Ocean as a marine gateway and is ringed by large cities and coastal industrial zones together with port facilities, all constituting a concentration of prime importance for socio-economic activities. The Trans-Tokyo Bay Highway (TTB highway), which crosses Tokyo Bay and provides a direct transportation link between the west and east sides of the bay, has long been a sort of “dream-come-true” project in Japan. As shown in Figure 2, linked to the Tokyo Bay Shore Highway, Metropolitan Inter-city Expressway, Tokyo Outer Ring Road, Tateyama Express-way, and others, it will play an important role as an integral part of the regional highway network to help promote spatial redistribution and multi polarization of urban functions, thus strengthening cooperation between cities and restructuring the metropolitan region. The TTB Highway is a project of 15.1 km in length designed as a toll highway to cross the bay by tunnel and bridge, and will require ten years to complete at a total cost of more than 1,438 billion yen (US$13.077 billion). Following more than 20 years of feasibility and environmental assessment studies, construction of this giant offshore highway project commenced in May 1989 as the first large-scale highway project with private-sector participation under the prevailing Road Law in Japan, and is now steadily proceeding toward the goal of completion in fiscal1997. This report outlines the entire TTB Highway project, including the waterproofing measures against high water pressure and the rapid construction method applied in the construction of shield tunnel sections.

Jan 1, 1997

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By I. Mazalov, G. Ospanova

Introduction Today, uranium is of great interest because of its application to nuclear power and nuclear weapons. Kazakhstan has been an important source of uranium for more than fifty years. All uranium products are exported. Results In Kazakhstan uranium exploration started in 1948 and developed in several parts of the country thru mining of hard rock deposits. There are known around 50 uranium deposits in six provinces: Shu-Sarysuyskaya (57%), North Kazakhstan (18%), Syrdaryinskaya (15%), Ilyiskaya (7%), Caspian (2%), Balkhash (1%). In the Northern Kazakhstan province, KazSabton took over Tselinny Mining & Chemical Co in 1999. In this province the stockwork is of Paleozoic and Paleozoic folded complexes origin. In the Balkash province some mining of volcanogenic deposits occurred during the Soviet era. This province’s stockwork is of Endogenous origin.In the Ili province uraniumis mainly found in uranium-coal deposits formed by oxidation of the lignite beds roofs. In the Caspian province the Prikaspisky Combine operated since the 1960s a major mining and processing complex on the Mangyshalk Peninsula. This led to the founding of Aktau. It was privatised as Kaskor in 1992 and operations ceased in 1994. The uranium occurrence is associated with the phosphorous from fossil fish bone detritus conglomeration. In the Chu-Sarysu province, which has more than half the country's known resources, both Stepnoye and Tsentralnoye have been operating since 1978 and 1982 respectively. Uranium mineralization occurred in the regional stratum oxidation zones. In the Syrdarya province slightly to the west of the province’s center the No.6 Mining group has been operating since 1985. Uranium mineralization occurred in the regional stratum oxidation zones.

Jan 1, 2007

By W. C. Brice

Minnesota's mineral resources are widespread and diverse (Figure 1). In addition to the nation's largest iron and manganese reserves, the state contains sizeable vanadium, copper, and nickel resources. Recently it has been determined that the proterozoic unconformities in Minnesota have a favorable potential for uranium deposits. Finally, major potential exists in Minnesota's archean greenstone belts for gold, silver, and copper-zinc massive sulfides. Many of the state's mineral resources have been found in environmentally sensitive areas. This is not surprising since the natural forces associated with the formation of mineral deposits are often the same processes that create unusual landforms. For example, much of the state's copper-nickel is found within and adjoining the Boundary Waters Canoe Area (BWCA) and Lake Superior. The history of mineral development on the Mesabi Iron Range has also created culturally sensitive areas. Early iron mining development required the workers to live close to their jobs, and mine wastes were dumped as near the mine as possible. Few, if any, foresaw the time when taconite would be economic to mine. Therefore, it is not unusual to find valuable taconite resources located under towns and waste dumps on the Mesabi Iron Range.

Jan 1, 1980

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.' The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. Results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed in this paper.

Jan 1, 2000

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide's Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998