Search Documents

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore 'beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

By D. Meadows, P. Carrato, E. Wingate, K. Churchill

Extracting lunar ice, to be processed into pure water or hydrolyzed into oxygen and hydrogen, faces many challenges. On the Moon icy-regolith deposits that contain up to 10% water are found within Permanently Shadowed Regions (PSR) at both lunar poles, where temperatures approach -220 ⁰C. NASA has identified several technology gaps that exist in developing these resources including: • Excavating large quantities of icy-regolith • Delivering large quantities of acquired resources • Hardware that is lightweight and energy efficient • Hardware that is reliable and durable. NASA uses public challenges to incentivize innovative approaches to closing these gaps. The Break the Ice Lunar Challenge provides over three million dollars in prize money to teams that compete in developing solution to mining the Moon. This paper describes the rules for this challenge and presents some of the proposed solution.

Feb 1, 2023

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By H. Haselhuhn

Filtration of hematite ore slurries can be a bottleneck in some hematite processing plants due to inadequate filtration rates caused by the dispersion of fine particles. Flocculation of fine particles in the slurry decreases the specific cake resistance of the filter cake allowing for increased filtration rates. CO2 sparging of hematite slurry was shown to increase the filtration rate by altering the pH and the surface chemistry of the particles. It was shown that an increase in filtration rate of 278% can be accomplished by lowering the pH from 11 to 6.5 using CO2. This was attributed to increased flocculation of hematite and silica particles in the ore.

Jan 1, 2012

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By T. J. McKeon

Partition curves are used to evaluate the separation performance of gravity-based concentrators. The partition curve is used to identify the nominal density cutpoint and relative sharpness of the separation. In addition, the graphical representation makes it possible to quickly identify the root cause of misplacement based on the characteristic shape of the partition curve. Partition curves have been traditionally constructed using data obtained from float-sink tests using heavy organic liquids. These toxic liquids are environmentally unfriendly and have been banned in several countries. Another method of establishing the partition curve is to introduce density tracers into the feed and plot the distribution to the lights and heavies. For heavy mineral separations, this approach is generally impractical due to the fine particle size. In addition, the partition data obtained using these existing techniques do not account for secondary factors such as particle shape that may influence the separation. In light of these problems, a methodology was developed for constructing partition curves using experimental data obtained from microscopic grain-counts. This technique, which essentially uses the different mineral species as density tracers, provides a powerful tool for evaluating heavy mineral separations. A case study is provided to demonstrate how this analytical approach can be used to assess and improve the separaton performance in an industrial upgrade plant.

Jan 1, 2005

By Steve Wiig

In 1987, the Rock Springs, WY district office of the US Bureau of Land Management (BLM) began to develop an automated system to store, maintain and manipulate more than 14,000 drill hole logs contained in the district's office files for various solid leasable minerals. The development of this system was based predominantly on a trial-and-error basis, with many procedural changes incorporated over time. The current Automated Drill Hole Database and Analysis System will continue to evolve with new software developments and increased personal expertise in this field. The mission of the BLM's Branch of Solid Minerals is mandated by a series of federal laws. The most important are The Mineral Leasing Act, the Federal Land Policy and Management Act, the Federal Coal Lease Amendments Act and the Surface Mining Control and Reclamation Act. Several regulations, promulgated from these laws, dictate that BLM must perform certain tasks and functions as part of its specific duties. The regulations that apply to the BLM Solid Minerals program are codified at 43 Code of Federal Regulations (CFR) 3400 for coal, and at 43 CFR 3500 for non-energy solid leasable minerals, such as sodium, phosphate and potash. Specific functions required of the Branch of Solid Minerals necessitates the use of geologic and drill hole data analyses. These functions can be divided into pre-lease and post-lease. Examples of pre-lease functions that normally require some level of drill hole data analyses include:

Jan 1, 1992

By S. J. Neethling

The flotation froth structure and motion determines the amount of entrained gangue that is collected to the concentrate. Despite this important role in the overall performance, the behaviour of the froth is still ill understood. To date, predominantly empirical models have been developed to describe entrainment. A fundamentally based model is described and used here in an attempt to improve the understanding of entrainment. This general froth simulator (UMIST FrothSim) allows the modelling of a wide range of flotation conditions, as it takes account of a large number of the physical phenomena that occur within flotation froths. The model firstly describes gas motion and bubble coalescence, and the water motion based on gravitational, viscous and capillary effects. The motion of the solids distinguishes between various solids classes based on hydrophobicity, particle size and density and models them by including the effects of Geometric and Plateau border dispersion, particle settling and the motion of the water. The aim of this paper is to show the applicability of this model to explain the observed entrainment and collection of gangue. This is done by comparing model predictions with the experimentally observed relationship between the gangue and water recoveries. The model predicts the identical trends, which are explained in terms of the interaction between the linear effects of water motion and hindered settling and the non-linear effect of particle dispersion.

Jan 1, 2001