Search Documents

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

By Verya Nasri

This paper will present the design and construction of a deep underground station of the Réseau Express Métropolitain (REM) project; the Édouard Montpetit station. The Édouard-Monpetit station is an interchange station that will connect the deeply sitting REM tracks to the existing metro station of the same name located closer to the surface. Édouard-Montpetit station is expected to be the deepest in North America, surpassing the famous Forest Glen Station. The various challenges and solutions put forth for the successful completion of this underground work are presented to serve as a valuable example for future deep excavation performed in urban area, in the close vicinity of highly sensitive structures.

Jun 13, 2021

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By Tuncel M. Yegulalp, Anuta Belova

This paper expands on the ZECA (Zero Emission Coal Alliance) technology, which is aimed at making coal a sustainable source of clean energy in the near future. The technology proposed immediate capture of carbon dioxide and other pollutants upon generation, thus alleviating their negative effects in the Earth’s atmosphere. ZECA proposes using chemical energy of coal to produce hydrogen; the latter is then used to produce electricity via fuel cells or Hyrogen-Oxygen turbines. In this study, a chemical engineering package, AspenPlus 12.1, is used to simulate the reactor (reformer) in which hydrogen is produced from methane water and lime as part of the zero emission power plant. Thermodynamic conditions, pressure and temperature, are optimized with respect to molar hydrogen production. Under the proposed conditions, molar conversion efficiency, carbon to hydrogen, of 95% is achieved. Further studies are required to model the complete power plant and to optimize it for efficiency.

Jan 1, 2005

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By K. G. Kebkal, R. Bannasch

"Because the operation of tethered underwater vehicles in the deep ocean or under drifting ice areas is very complicated or impossible, the application of autonomous underwater vehicles (AUV) is preferred or even the only possible solution. However, this implies the possibility of a direct and real-time control over all AUV functions, which is only achievable with the availability of accurate positioning/navigation and a high-speed communication link. This paper presents a flexible bottom- or surface-based solution enabling high positioning accuracy of underwater objects (harvester, AUVs, bottom nodes); specifically, a multifunctional system that combines Ultra Short Baseline (USBL) transceivers and Long BaseLine (LBL) stations deployed at a large depth. Moreover, each baseline transponder is equipped with a high-speed communication device to provide the means for real-time AUV control based on the information about its current position, e.g. navigate it with direct commands and operating its actuators and other mechanisms. Moreover a communication link with a high data rate can provide valuable visual information from the operation area.Depending on how many nodes the LBL grid comprise has, target transponder positions can be estimated with an accuracy of several to tens of centimetres. The purpose of the paper is to present the experiments with all key elements of the multifunctional Hydro-Acoustic USBL-aided LBL Positioning and Communication System."

Sep 1, 2014

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By Tim O’Neil

ISO 9000 is a system of quality standards that originated in Europe in the 1980s and has since been widely adopted by manufacturing companies throughout the world. The ISO 9000 standards have received less attention in the minerals industry. But, in part as a result of customer pressure, a trend is beginning to emerge for minerals producers to seek ISO certification. This is especially true among producers of industrial minerals. In early October 1994, SME's Industrial Minerals Division held a conference "ISO 9000 - uniting industrial mineral producers and consumers into quality partnerships," in Nashville, TN to bring people from the industry together to talk about their experiences with ISO 9000. William J. Miles, of Bentonite Corp. Inc., and A. Frank Alsobrook, of Alsobrook and Co., were cochairmen of the meeting. In his introductory remarks, Miles noted, "ISO 9000 is more than a quality program. It is a quality philosophy. Appropriately imple-mented, it is a contract between the supplier and the customer. It leads to continuous quality improvement and reduced manufacturing costs."

Jan 1, 1995

By N. Sloan Dworian, Alyssa Smith, Ian Kellogg

Many studies have utilized magnetic susceptibility data to fingerprint porphyry copper centers; however, usage of magnetic susceptibility data to identify trends in a Climaxtype molybdenum porphyry deposit is limited. To better understand potential petrophysical signatures in a Climaxtype Mo porphyry deposit, magnetic susceptibility data was gathered at regular intervals from core holes across the Climax Mine, targeting major lithologies and styles of alteration. Preliminary analysis suggests that there are quantifiable patterns which may correspond with the mineralizing intrusions. This data can complement current mapping and exploration techniques to identify Climax-type molybdenum porphyry centers and likewise further the exploration potential for this deposit type.

Feb 22, 2026

By J. Hines

Traditionally, fuel oil or diesel was the collector of choice in coal flotation, but in recent years these materials have come under increased scrutiny because of concerns about the toxicity of some components. In response to these concerns, Georgia-Pacific Chemicals LLC has commercialized a patent pending coal collector (Talon® 9400 reagent) that is 100% derived from the pulping of trees. This study presents a comparison of yields and recoveries for different coal collectors, including the one derived from the pulping of trees.

Jan 1, 2011