Search Documents

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By N. A. Barcza

This publication records the proceedings of the Tenth International Ferroalloys Congress, INFACON X, and the third INFACON hosted in South Africa. The Proceedings of the previous two South African congresses in 1974 and 1992 serve, as this volume does, as a valuable record of the papers presented at these important events. This publication comes at a time in South Africa?s democratic development where the theme ?Transformation Through Technology? is very appropriate. The ferroalloy industry has played an increasingly significant role in transformation and black economic empowerment in South Africa, particularly through the advancement and sharing of technology. INFACON X plays an important role in this process, and the stakeholders and organisers of this Congress are thankful for the opportunity to hold this event at this time of transformation in our country. The world of ferroalloys, as well as that of the steel and stainless steel industries, has continued to change rapidly. Recent innovations, better use of resources, increased awareness of environmental issues and ongoing efforts to improve occupational health and safety are among the topics addressed at INFACON X and in these Proceedings. The theme of ?Transformation Through Technology? has been chosen to reflect the regional and global developments in the ferroalloy industry, and the crucial role that technology plays. The Proceedings of INFACON X, the first Congress in Southern Africa of the new millenium, represent a milestone in the technical developments in this major global industry. It contains almost eighty papers in twenty Sessions, from authors in twenty countries, covering raw materials, reductants, energy, electrodes, refractories, furnace design, post taphole services, modelling, simulation, control, sensors, fundamental issues and the applications of ferroalloys as related topics. The major ferroalloys, namely ferrochromium and ferromanganese, are covered extensively in many interesting papers. This comes as no surprise, since South Africa is the leading producer of ferrochromium and also plays a major role in the supply of manganese ore and alloys. Papers on ferronickel, silicon and ferrosilicon ensure that all the large-volume ferroalloys are addressed. These Proceedings of refereed papers of high quality will serve the ferroalloy industry for many years to come, as has been the case with previous INFACON events. For the first time in the history of INFACON, the Proceedings will be available both in bound and in a searchable electronic CD-ROM format. We appreciate the time and effort that the authors and referees have devoted to making this publication a really valuable document. Their contributions are recorded for posterity and reflect the advancements they and their colleagues have made to benefit the ferroalloy industry. Without these ongoing improvements, the industry would stagnate and not fulfil its role in the advancement of mankind. All papers included in these Proceedings were peer-reviewed by at least two referees. About 130 referees were sourced internationally to fulfill this function, and their valuable technical and editing inputs are gratefully acknowledged. Finally, I would like to thank the Technical Programme and Publication committees, led by Dr. Lloyd Nelson and Dr. Noël Machingawuta respectively. Without the tireless efforts of these individuals and their Committee members, the technical programme and these Proceedings would not have been the success they certainly are.

Jan 1, 2004

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By Onuralp Yücel, Süheyla Aydin, Erçin Ersundu

Turkish iron and steel sector, the base of which was established in the 1930?s, plays an important role in the industrialization and development of the country?s economy. In Türkiye this sector is the major consumer of ferroalloys. There had been a great improvement in Turkish Iron and Steel industry, especially after the 1980?sand as a result, 20.9 million tons of yearly crude steel production placed Türkiye 11th in the global steel output and 3rd in Europe. 15 % of steel produced in Türkiye is flat products, while the long products make the rest. The product composition and the general characteristics of steel production process led to an increase in ferroalloy consumption. Domestically consumed ferroalloys are especially ferromanganese, silicomanganese, and ferrosilicon. As of today, ferroalloy production capacity of Türkiye is 173,800 tons/year; 161,500 tons of which is ferrochrome with high and low carbon grades, 7,300 tons of ferrosilicochrome and the rest is ferrosilicon (5,000 tons/year). Türkiye is one of leading ferrochrome producers in the world considering the above mentioned production figures. However, this production is mainly exported since Türkiye?s stainless steel production level is modest requiring low amounts of ferrochrome. The products of iron and steel industry in Türkiye require large quantities of other ferroalloys, which make Türkiye a major importer and exporter of ferroalloys. The aim of this work is to present production, consumption, import and export quantities of: ferrochrome, ferromanganese, ferrosilicon, ferromolybdenum, ferrotungsten, ferrotitanium and ferrovanadium of Türkiye, between 1990 and 2006.

Jan 1, 2007

By D. J. Burger

This paper will highlight the system components of a successful underground mining automation project recently launched at DeBeers Finsch Mine. It will also show that integration of short-term mine planning with other upstream and downstream mining processes in the extraction of kimberlite ore from a block cave is not just critical to the future sustainability of this underground mining operation but also for profitability and cost-effectiveness. This paper will discuss the information data flow required from the mine-planning process through to production for underground block cave mining. The benefits associated with this type of integrated mine planning and automation system will be highlighted.

Jan 1, 2006

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By S. Burks

This paper develops the themes explained at the previous SAIMM Platinum conference by Whittle and Burks1. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long- term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: ? An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated ? An existing operation with an integrated portfolio of mines, concentrators, smelter and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets ? An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated ? An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the Owner?s team.

Jan 1, 2012

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By S. E. Cook

This article uses the case of the Royal Bafokeng Nation to argue that royalties and dividends from mineral resources, if managed well, can provide direct benefits to the surrounding community even while the state collects its share of mining revenues through taxation. The key to this model is the effective management of the resource income flowing into community coffers. Where some of this income may fund urgent interventions in the community, a portion of the income can also be used to establish an intergenerational wealth fund to meet the needs of future generations. As a depleting resource, minerals like gold and platinum are not a sustainable source of income, and must be replaced over time by more regenerative income streams. These strategies and dynamics are manifest in the Royal Bafokeng Nation?s status as both community and quasi-municipality, a labour hosting and a labour sending community, a mine operator and a mine owner. The Royal Bafokeng Nation also owns one of South Africa?s largest community-based investment companies, which channels revenue derived from platinum deposits into a broad investment portfolio that in turn funds an aggressive social development program for 150,000 people living in twenty-nine rural villages.

Jan 1, 2013

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003