Search Documents

By K Kongolo, M K. Kalenga

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electrochemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electro won. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present into solution will contaminates the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis..This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated : Co2+ concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4 additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By S Rupprech, T Lund, H Fourie, PH van Rooyen, NM Vegter

Rosh Pinah Zinc Corporation (Pty) Ltd (RPZC) operates an underground mine at Rosh Pinah in southern Namibia producing zinc and lead sulphide concentrates. It currently mines around 0.7 Mtpa run-of-mine ore containing around 6-10% zinc and 1.5-3.5% lead. As part of past exploration and current intensified exploration, a massive continuous low grade ore body was identified which grades at around 3% zinc equivalent. This ore body is near current mining infrastructure and could be amenable to bulk mining methods. In the present paper a concept is presented on how it could be exploited. As a precursor to exploitation of the low grade a number of enhancements are proposed for the current mining operations including: ? shortening load-and-haul distances by extending the conveyor raise further down the mine in a phased manner and back-filling of waste into mined-out stopes; ? use of mobile crushing plant at the crusher tip, and; ? installation of a system to allow scoops to load directly from stopes into ore passes close by combined with truck loops to haul from these ore passes to the crusher tip. To exploit the low grade ore body the following concepts are proposed: ? open stope mining from two areas at a total rate of up to 2 Mtpa; ? underground pre-beneficiation of mined low-grade ore near the stopes using either dense medium separation or X-ray sorting; ? pre-beneficiated tails back-filled to mined-out stopes and; ? pre-beneficiated product transported to surface by linking into proposed run-of-mine conveying system.

Jan 1, 2007

By A. Kostin

GIS and multivariate geometric distribution have been used to predict the association of high-level intrusives with hydrothermal alteration related to iron oxide Cu-Au (IOCG) mineralizing systems. Several examples in the Russian northeast are presented in this paper. IOCG ore deposits can have enormous geological resources containing significant reserves of base, precious, and strategic metals, and hence are economically attractive targets for mineral exploration. To date, examples of this type of mineralization have not been reported from the northeastern area of Russia. The Tarinskiy ore cluster, located in Eastern Yakutia, shows brecciated altered rocks with sulphide and iron oxide cement, which is typical for IOCG mineralization of the iron oxide Cu-Au±U type. This cluster was formed near surface and is linked with the Rep- Yuruinskiy pluton. It has potential to host new world-class precious metal deposits in northeastern Russia

Jan 1, 2014

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000

By R. M. Goktan

Rock brittleness plays an important role in the cutting action of picks on rock surfaces. It controls the ease with which cracks can propagate through the rocks. Although rock brittleness is known as a property that contributes to the cuttability of rocks, despite considerable research effort, there is still much uncertainty about the relation between rock brittleness and rock cutting efficiency. This fact can be attributed to the lack of a universally accepted brittleness concept and a brittleness measurement method. The existing publications of some researchers have, in a way, tended to confuse the understanding of brittleness in the general field of rock excavation where it is expected that the energy consumption of cutting should decrease with increasing brittleness of rock, other conditions being equal. However, this sometimes conflicts with the brittleness concept commonly used in rock mechanics, where the more brittle the rock the higher its mechanical strength. The ratio of rock compressive strength to tensile strength is considered by many authors to give a valuable brittleness index for drag pick operations. Hence, in this contribution the ratio of uniaxial compressive strength to tensile strength BI is considered as an index of rock brittleness, and a new methodology is proposed for its use in rock cutting efficiency analyses of drag tool operations. Validation of the suggested approach is supported by available experimental data in the literature. Contrary to the conclusions reached previously by other authors, it is shown that an increase in rock brittleness is accompanied by an increase in the cutting efficiency, other conditions being equal. Keywords: brittleness index, rock brittleness, cutting efficiency, specific energy, rock excavation.

Jan 1, 2005

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By H. Kotzé

Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and mineral separation plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2slag and 145 kt/a of pig iron.

Jan 1, 2006

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006

At Namdeb, submerged beaches are earmarked for sampling and future mining and various sampling configurations are tested for optimality through the use of spatial simulations. For the creation of these virtual orebodies, basic statistics and variograms are needed, but in this specific instance no data exists from which the necessary parameters can be determined. The best that can be done is to use proxy data from onshore beaches, with adaptations where needed. The reworking of raised beaches during periods of rising and falling sea levels in some cases destroyed the internal beach structures, and it is very difficult to determine the variograms. A method is proposed whereby simulated annealing is used to adjust the sample locations to align the data pertaining to beach crests or cliff lines, thus improving the variogram structure along the shoreline in the direction of the highest geological continuity.

Jan 1, 2014

By M. van Schoor

The bulk of the world?s platinum production originates from the Merensky and UG2 reefs within the Bushveld Complex, South Africa. Both the Merensky and UG2 reefs are disrupted by faults, dykes, potholes and iron-rich ultramafic pegmatite bodies (IRUPs)?features that impact negatively on production, planning and safety. It is therefore advantageous to know of their presence and geometry ahead of mining. To date, no geophysical technique has been successfully applied to the routine mapping of mine-scale potholes and IRUPs. These disruptive features may vary from a few metres to several tens of metres in diameter. In this paper the applicability of in-mine electrical resistance tomography (ERT) to map potholes and other disruptions to the continuity of the Merensky and UG2 reefs ahead of mining is demonstrated using two case studies.

Jan 1, 2005

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012