Search Documents

Discussion of the above paper by G. J. van JAARSVELDt Mr Ortlepp's paper is important, and deals with a subject towards which much controversy and insufficient basic scientific logic, in my opinion, have been directed. He attempts to remedy some of our unscientific popular misconceptions, and for this we thank him. However, I regret to say that experience has shown that some of his statements cannot be allowed to pass unchallenged. Author's reply Mr Van Jaarsveld's contribution is welcome because it provides an opportunity for me to clarify certain points that were perhaps not adequately explained in the paper.

Jan 1, 1979

By J. A. Ryder, M. U. Ozbay

An ERR-based methodology is presented for use in the re-assessment of the performance of stabilizing pillars, taking into account the effects of fracturing that can occur in pillar foundations under conditions of high stress. It is shown that the damage in the foundations of under-designed pillars can cause up to 30 per cent increases in ERR compared with the ERR for pillars with unfractured foundations. Despite this reduction in assessed performance, stabilizing pillars are still generally found to result in substantially lower ERR levels than alternative methods of reducing ERR, such as the use of stiff backfill or backfill ribs.

Jan 1, 1990

By B. Nemutudi, X. Zhang, B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, S. Pikinini

The comparison study on adsorption of potassium normal butyl xanthate (PNBX) and sodium (nbutyl) dithiocarbamate (SNBDTC) on sperrylite mineral forms a basis in understanding the floatability improvement and paves a way for the design of collectors that may impact on a wide range of arsenide minerals. This study used a computational density functional theory (DFT) and experimental microcalorimetry approach to determine the adsorption energies of PNBX and SNBDTC collectors onto a sperrylite mineral surface. From a computational aspect, we considered the most stable surface plane of (100) surface, which had been found to give the lowest surface energy, compared to the other surface planes. It was observed that the PNBX and SNBDTC preferred to bridge on the As and Pt atoms through the S atoms. These findings showed that the collector adsorbed on the surface through both Pt and As atoms and indicated that the As atoms were significantly active in the adsorptions. We found that the adsorption energies were in the order: SNBDTC (–278.38 kJ/mol) > PNBX (–270.92 kJ/mol), indicating that the dithiocarbamate had stronger exothermic adsorption than the xanthate. From the microcalorimetry test it was also found that the SNBDTC was more exothermic than the PNBX and the adsorption energies were: SNBDTC (–473.50 kJ/mol) > PNBX (–331.13 kJ/mol). These results showed that the nitrogen atom in the SNBDTC collector had a great influence on the adsorption strength of the collector on the mineral surface. This is due to the electron deposition behaviour of nitrogen atoms compared to the electron withdrawing character of oxygen and as such the SNBDTC showed better collecting ability than the PNBX. These results paved the way for the design of collectors for sperrylite and other arsenide minerals and suggested that nitrogen in a collector may significantly improve the ability of the collector for improved recovery. Keywords: Computational modelling, microcalorimetry, SNBDTC and PNBX collectors, adsorption energies

Jan 1, 2020

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

By C. J. Badenhorst

Occupational illnesses and diseases tend to be chronic and are generally characterized by temporary or permanent physical dysfunction. With the exception of some symptoms, they are not generally visible. Therefore, safety overrides health in mining because occupational ailments take years to develop and management observes less physical trauma, if they witness anything at all. Occupational health issues need to be addressed systematically, encompassing all aspects of the interaction of employees within the work environment. Risk assessment is central to the management of occupational health. This should not be seen as a complex process and may involve little more than simply considering the consequences of one?s actions before starting work. Competent risk assessment provides the starting point and defines the scope of further action. The objectives and final use of an occupational health risk assessment determine the process and the method by which it is carried out. The occupational health risk assessment is therefore a systematic procedure to identify potential health hazards, evaluate the extent of exposure subjectively and/or objectively, and to establish the need for, and effectiveness of existing control measures. Furthermore, it facilitates the drafting of occupational exposure monitoring, medical surveillance and occupational health education programmes. Various models for conducting occupational health risk assessment provide step-by-step guidance for the identification and assessment of significant occupational health hazards and assist in producing suitable and significant occupational health risk assessments. The paper gives an overview of an occupational health risk assessment model based on the basic principles of occupational health and the legislative requirements, which will simplify the occupational health risk assessment process and ensure a sound base for the development of all other occupational health systems.

Jan 1, 2004

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

By P. H. Botha

An account is given of the procedures used by the South African Iron and Steel Industrial Corporation (Iscor) for tests on the flotation of coal fines, and some of the beneficiation problems encountered with coal from Durnacol, Grootegeluk, and the Soutpansberg area are discussed. These, and other South African coals differ from overseas coals in that they contain a high percentage of fixed ash, which means that they have to be crushed more finely for liberation and that they then contain more fine material (smaller than 0,84 mm). In addition, the coal from the three areas mentioned occurs in fine layers and seams, and contains many intergrown particles.

Jan 1, 1980

By K. R. Vost

Calculations are given for the reduction in amplitude and change in phase of the diurnal variation in air temperature as the air flows through a mine. The concrete lining of a typical shaft was found to have a much greater effect than the steelwork. An increase in the conductivity of the concrete, or filling of the steelwork with water, did not have enough effect on the rise in air temperatures underground during the day to justify the costs involved. The steel temperature followed the air temperature much more closely than the concrete temperature did. Calculations are given for the heat stored in steel and concrete during the day.

Jan 1, 1980

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By N. Naude, W. P. Roux, O. Kaba

Ceramic filtration plates are used for dewatering slurries with high solid concentrations and particles in the size range of 30 μm to 150 μm. After extensive operating times, the ceramic filter plates at Minas Rio in Brazil begin to blind due to the precipitation of barium sulphate on the surface of the ceramic filter plate, which reduces the overall efficiency of the filtration process. Further research is needed to identify the barium precipitate phases on the blocked filter plates and its thermodynamic and kinetic behaviour in the system. A crystallography analysis was performed on the sample and the results showed that there are two different sets of precipitates formed on the filter plate: grey crystals which were large and scatted on the filter plate and red micro crystals that covered the entire surface of the filter plate. The red microcrystals on the sample were identified with XRD, which indicated that the sample contained barium sulphate in the mineral form barite. Experiments were conducted to determine the optimum conditions under which barium precipitation will occur. The conditions tested as a possible driving force for barium sulphate precipitation were the effect of temperature, pH and concentration. The pH and temperature ranges were pushed to both the lower and higher boundaries. The effect of temperatures as low as 15oC was studied and pH levels of 7 and upwards. The first nuclei started appearing at a pH of 7 but significant growth is promoted at higher pH levels. The X-Ray diffraction analysis confirmed the phase of the precipitates formed, and the orthorhombic crystallographic structure formed is a characteristic of barium sulphate. Keywords: Iron ore, barium sulphate, temperature, pH, concentration, morphology, and ceramic filter plate

Jan 1, 2020

Mintek now offers a service for the accurate measurement and analysis of air pollution in South Africa. 'The deteriorating air quality and general degradation of the environments in industrialized and urban regions of South Africa have been of concern for more than a decade', says Mintek's Dr Johann Engelbrecht. 'The accompanying effect on health, visibility, and damage to property and the environment have prompted the public, authorities, and industry to take appropriate action. A recent study conducted by the Medical Research Council on schoolchildren in the Vaal Triangle, clearly demonstrated the relationship between the deficient quality of the air in that area, and the resultant respiratory diseases.

Jan 1, 1996

The First International Symposium on Seismicity in Mines, organized by the South African National Group on Rock Mechanics in collaboration with the South African Institute of Mining and Metallurgy, was held in Randburg (near Johannesburg) from 13th to 17th September, 1982. It was the first attempt to provide an international forum for the consideration of seismic problems specifically affecting mines or associated with mining. Numerical mathematics The South African Society for Numerical Mathematics and the Computer Science Department of the University of Natal are organizing the Ninth Symposium on Numerical Mathematics to be held in Durban from 18th to 20th July, 1983.

Jan 1, 1983

By J. Meintjest

As you pointed out, furnace power factor (and consequently transformer MVA rating) depends upon the inductive reactance, and so it is desirable to design for the lowest possible value of this parameter. The further introduction on the primary side of the transformer of capacitors, whether in shunt or in series, increases the network power factor but does not alter the furnace power factor; that is, the phase angle between electrode to- hearth voltage and current remains unchanged. Corrigenda The following amendments should be made to the article entitled 'Coal-preparation routes for maximum coal recovery', which was published in the August issue (vol. 80, no. 8) of this Journal:

Jan 1, 1980

Crossroads for Students Students in their matriculation year, whatever their background, have reached a crossroads in their lives: behind them lie the relatively carefree years of childhood; ahead lies the whole of their working lives. Whether those working lives will be rewarding and interesting depends to considerable extent on whether they get 'a good matric' and carry on to some form of further education. IPMI awards 1985 Nominations for the 1985 Awards are now being accepted by the Awards Committee of the International Precious Metals Institute. THE DISTINGUISHED ACHIEVEMENT AWARD was established to recognize important career contributions to the advancement of precious metals, be it technological, economic, or business.

Jan 1, 1984

By H. T. Kaiser, P. De Waal

The Alusaf aluminium smelter at Richards Bay by H. T. KAISER, B.Sc. (Pta), M.B.L. (Unisa) (Visitor) and P. DE WAAL, B.Sc., B.lng. (Mech.) (Stell.) (Visitor) A description is given of the aluminium smelter at Richards Bay, which operates on the Hall-Heroult electrolysis principle. The annual output of metal (average 99,7 per cent aluminium) is approximately 7S 000 tons. Since its commissioning in 1971, the plant has fulfilled South Africa's total demand for low-alloy rolling slabs, extrusion billets, remelt ingots, and electrical conductor rod. The plant layout allows for sufficient expansion of its capacity to meet longterm increases in demand.

Jan 7, 1977

By R. K. Brummer

The support of stopes and tunnels in South African gold mines subject to rockburst damage requires special attention. The interaction of a seismic wave with either a stope or a tunnel is subject to a number of variables, namely the distance from the source of the event, the ground velocity, the orientation of the excavation with respect to the direction of the seismic wave, and the geology and fracturing around the excavation. This paper discusses these factors in relation to the support requirements in stopes and tunnels. The need for the integration of hydraulic props with stope support and the use of yielding anchors for tunnel support are emphasized.

Jan 1, 1988

OFS Branch Minutes of the General Meeting Held at the President Steyn G.M. Ltd Canteen on Wednesday, 13th November, 1974, at 3.55 p.m. Mr D. A. Smith (Chairman of the O.F.S. Branch) was in the Chair. There were also present: Nim reports Report no. 1696 The preparation and certification of a reference sample of a preciousmetalore. Report no. 1705 The effects of various matrix elements on the efficiency of the fire-assay procedure using nickel sulphide as the collector. Report no. 1720 The initial development of processes for the direct leaching of iron-nickelcopper mattes containing platinumgroup metals, and for the production of ferronickel.

Jan 5, 1975

By J. A. L. Napier

SYNOPSIS Many tabular mining problems can be modelled effectively by displacement-discontinuity techniques, which can be extended directly to represent fracturing on discrete planes and movements on planes of weakness. This paper presents a unified method for computing the energy changes that occur when multiple discontinuities intersect and are extended incrementally. It shows how this method can be used to deduce energy-release information for standard layout problems and, in addition, how the technique can be incorporated in numerical procedures based on the displacement-discontinuity method. Examples are given to demonstrate the effects of off-reef fracturing and the importance of stope-fault intersections during seismic events.

Jan 1, 1991

By J. H. deur Potgieter

This paper, 'A review of the biological treatment of cyanide-bearing waste water' discusses the necessity for the treatment of cyanide-bearing waste water with a view to the avoidance of environmental pollution, and the limitations of the available chemical and physical processes are referred to briefly. The sources of cyanide-bearing waste waters are mentioned. The mechanisms of production and utilization of cyanide by fungi and bacteria are discussed. The work done in connection with the biological removal and destruction of cyanide is summarized, the successes achieved are described, and the relevant processes are listed. In conclusion, some advantages of biological processes for the removal of cyanide are mentioned.

Jan 1, 1991

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986