Search Documents

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By R. V. Higgins

A computer program is presented to calculate the shape factors and volumes of cells from a potentiometric model, using coordinates of the inter-sections of the stream lines and equal potentials and a few additional coordinates. Shape factors are used in flow computations when the geometry is complicated. The program also includes computer instructions to divide the channels into cells of equal volume and to obtain the shape factor for each of these equal volume cells. An illustrated example using the potentiometric model for the waterflood of a seven-spot well-spacing pattern is presented. The information contained in the report is of value not only to those allied to the subject but also to others, because many of the techniques can be conveniently used in formulating other computer programs.

Jan 1, 1966

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By Robert F. Randolph

Real-world levels of attenuation from hearing protection devices are usually much lower than the rated values obtained under near-ideal circumstances. The shortfall is even more extreme for earplugs than it is for earmuffs, primarily because of the complicated process of fitting the plugs within the ear canal. This study examines the use of a commercially-available lubricant for hearing aids to determine whether it would facilitate improved fit and attenuation for earplugs. In this experiment, ten participants inserted earplugs with and without using the lubricant. Average attenuation was assessed with the Real-Ear-Attenuation-at-Threshold (REAT) technique, and showed over 5 dB improvement when the lubricant was used. Participants obtained an 85% mastery rate using the lubricant versus a 50% mastery rate without. These results indicate several possible applications for improved earplug performance in real-world settings where hazardous noise is unavoidable and effective hearing protection is necessary.

Jan 1, 2008

By A. E. Ketler

The Bureau of Mines Research Program has defined per coal miner's illumination needs. Due to similarity in the environment in which coal and Hardrock miners work, coal mine illumination technology has been applied to Hardtack room and pillar mines.

Jan 1, 1977

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By A. J. Fejes

The purpose of this Bureau of Mines report is to provide mining industry personnel and regulatory authorities with a subsidence-reference list and annotated bibliography that will aid them in locating subsidence information and in developing their own subsidence information sources. Over 700 references are listed in the Bureau's subsidence information center bibliography; approximately 600 of these references were obtained for assessment. Of these 600 references, 167 were selected to be rated, categorized, and annotated. All literature referenced in this report was published prior to 1984. Table 1 is a cross - referenced index that classifies and rates selected references with respect to specific keywords. References are rated not on quality of content but rather on applicability to given subject areas. Appendix A is an annotated bibliography of the references listed in table 1 and provides further information of each article to aid the user in selecting articles for specific areas of subsidence technology. Appendix B is a copy of the subsidence information center bibliography.

Jan 1, 1985

By John W. Sweeney

Shales and clays from Illinois were sampled, tested, and evaluated to determine feasibility of producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the 1 ,,,y of the Pennsylvanian shale units are discussed. Chemical, X-ray spectrographic and X-ray petrographic analyses were run on the samples to determine if a correlation existed between chemical mineralogic composition and expansion. Preliminary expansion testing was conducted in a muffle furnace. Rotary-kiln tests were conducted in a 16- inch by 14-foot rotary kiln. The weight of the aggregate ranged from 27 to 59 pounds per cubic foot. Concrete cubes employing the aggregate were tested to determine the qualities of the concrete. Compressive strength of the concrete using the 7-bag of cement cement per cubic yard mix, after autoclave curing for 6 hours, ranged from 2,950 to 6,750 psi. No correlation was found between the chemical, X-ray spectrographic, and X-ray and petrographic analyses and expansion, Sixteen samples made suitable lightweight aggregates in the laboratory rotary kiln. The expansion temperature range of eight of the samples was extremely narrow, and difficulties would probably be encountered in processing these materials commercially.

Jan 1, 1965

By Doss H. White

In 1989, Alabama's nonfuel mineral industry produced a State record of $463 million of nonfuel mineral commodities, an increase of $4 million over that reported by the State's mineral producers in 1988. The new record marked the fourth consecutive year in which mineral production increased over that of the previous year. Alabama ranked 22d among the States in total mineral value. Cement, stone, and sand and gravel were the three leading mineral commodities produced, accounting for 77% of Alabama's total mineral value. During the year, there were several acquisitions by Alabama cement and stone companies, and the only tantalum mine in the United States completed its first full year of operation.

Jan 1, 1991

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

The reversal of smoke products-of-combustion (POC) from a mine fire was determined in a mine section with the airway connectivity of an electrical Wheatstone bridge. Four diesel-fuel fire experiments with fire heat-release rates between 504 and 771 kW were conducted in the Safety Research Coal Mine (SRCM) located at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL). Smoke reversal propagated upwind from the fire with significant leakage into the upwind diagonal airway and without causing a complete reversal of airflow in the diagonal airway. A control measure consisting of a brattice suspended half entry height from the entry roof was determined to abate the smoke rollback. Computational fluid dynamics (CFD) analysis of the smoke movement agreed with the measurements.

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930