Search Documents

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data for motor gasolines sold during the summer of 19363/. The third report of the seriis gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative that others.

Jan 1, 1937

This appendix is composed of five sections, each of which is tabbed for ease of access. The sections are as follows: ? Fire incident report forms for underground mine fires. There is one form for each incident listed in Table II-1a. They are ordered chronologically with incident numbers corresponding to those in Table II-la. ? Fire incident report forms for surface mine fires. There is one form for each incident listed in Table II-lb. They are ordered chronologically with incident numbers corresponding to those in Table II-lb. ? Journal article report forms. There is one form for each article reviewed. They provide supplemental information to that contained in the fire incident report forms for selected fires. Index 11-14 keys the journal article report forms to the appropriate fire incident report forms. ? Non-reportable incident descriptions for underground mine fires. This is a listing of underground fires for which MSHA regulations do not require formal reports. ? Non-reportable incident descriptions for surface mines. This is a listing of surface fires for which MSHA regulations do not require formal reports. This appendix is intended to be used in conjunction with the tables and indexes contained in Volume II of this report and, as such, should be considered an integral part of Volume II. The indexes in the body of Volume II provide a means of ready reference to the underground and surface mine incident report forms. For those readers with interests other than those indexed, Tables II-la and II-1b can be used to locate specific incidents of interest. Complete incident information can then be obtained from the corresponding report forms in the first two sections of this appendix.

Jan 1, 1980

By Edmund S. Leaver, A. P. Towne, Jesse A. Woolf

Part of the work of the Precious Metals Section is to conduct oretesting experiments on ores selected as representative of various mining districts or areas . The projects are authorized by the Metallurgical Division , and only those ores in which gold and silver or gold or silver constitute an essential part of the total values are assigned to the Precious Metals Section . Such ores include those containing the precious metals only as commercially important ingredients , as well as those containing base metals such as copper , lead , and zinc along with the gold and silver . In many instances the "ore " may be a tailing product of a grade good enough to warrant retreatment , or a concentrate for which it is desirable to develop a method of treatment to avoid the expense of shipment to a smelter . It is evident that in general the greater part of this ore - testing work is done according to standard testing procedure , such as cyanidation, amalgamation, gravity - concentration , and flotation , or a combination of these methods . The standard methods of conducting such tests have been outlined in previous reports of ore - testing studies . However , since the inauguration of this oretesting program 6 years ago , the ores submitted under authorization have become increasingly more refractory to simple methods of treatment. Consequently, a considerable number of the projects completed during the fiscal year 1941 have required an unusual amount of work and in some instances have developed into real research problems . For such ores more complete microscopic and spectroscopic examinations and more complete chemical analyses

Feb 1, 1942

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By D. E. Welcome, T. W. McDowell, R. G. Dong, S. F. Wiker

Workers using vibrating hand tools have the potential for developing health problems associated with repeated forceful actions and exposures to hand-transmitted vibration. Hand-arm vibration syndrome (HAVS) and other hand-arm system disorders have been associated with such exposures.1-2 To better assess health risks, comprehensive evaluations of these exposures must include quantitative assessments of hand-tool coupling forces; unfortunately, no standardized method for quantifying hand forces exists. Handle instrumentation may be ill-suited for some field environments. Psychophysical force-recall techniques may provide alternatives to handle instrumentation. A thorough understanding of the effects of vibration and other factors on force-recall accuracy and reliability is important before such methods are applied in risk assessments. Methods In this study, the effects of vibration and other factors on the accuracy of psychophysical force-recall were explored in two experiments. Twelve male subjects participated in the first experiment. The second experiment employed 20 participants (10 female, 10 male). In each experiment, participants applied specific grip and push forces to an instrumented handle mounted on a shaker system. Participants were exposed to sinusoidal vibration at frequencies that ranged from 0 Hz to 250 Hz. Three levels of applied force (low: grip = 15 N/push = 25 N, medium: grip = 30 N/push = 50 N, and high: grip = 45 N/push = 75 N ) and two levels of vibration magnitude (low: ANSI 4-8-hr limit and high: ANSI <0.5-hr limit)3 were examined. During the vibration exposure period, participants were provided with visual feedback while they attempted to “memorize” the applied grip and push forces. At the conclusion of the vibration exposure/force memorization period and a controlled rest period, the participants tried to duplicate the grip and push forces on a non-vibrating handle without the aid of visual feedback. The effects of different vibration frequencies, vibration magnitudes, and grip and push force levels were tested in a random order from trial to trial. Results Participants tended to overestimate grip and push forces. Depending on exposure conditions, error means ranged from 2 N to 10 N. The ANOVA revealed that force-recall errors for exposures between 31.5 Hz and 63 Hz were significantly higher than those at other vibration frequencies (p < 0.05). The frequency effect is depicted in Figure 1. Error means were greater when participants were exposed to the higher vibration magnitude (mean = 9.1 N, 95% CI = 8.2-10.1 N) when compared with the lower vibration magnitude (mean = 4.9 N, 95% CI = 3.9-5.8 N) (p < 0.05). The effect of vibration magnitude is shown in Figure 2. The average error for

Jan 6, 2006

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By ALBERT E. HALL, Arno C. Fieldner, Alexander L. Field

As a safeguard against excessive clinker troubles, specifications for the purchase of coal can be drawn to include the "softening" or "fusing" temperature of the ash. The value of such information has been recognized by the Bureau of Mines and has induced the bureau to investigab~ laboratory methods of determining the fUSIbility of coal ash, and the bearing of the results on clinker formation in fuel beds. The bureau realized that the fusibility of a mixture of oxides and silicates snch as is comprised in coal ash ,'aries according to the conditions under which tests are made, and that in the absence of any generally accepted method, no agreement is to be expected among tests made in differ«:-nt laboratories. Indeed, Marks a has recently called attention to differences as great as 3900 C. that were obtained with the same sample of ash by two different laboratories. Therefore if a fusion-temperature clause is to have any place in specifications for coal, a standard m('thod of t('sting should be adopted in order to insure comparable results by different laboratories and to obtain the softening or fusing temperature of the ash unde:'r conditions similar to those of a fuel bed. After a consistent method has been devised for obtaining comparable:' results at different laboratories, there will remain the correlation of these results with those from the burning of coal in furnaces before the value of fusibility tests in coal specifications can hE' finally determined.

Jan 1, 1918

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By Neil J. Mansfield, Setsuo Maeda

The purpose of using experimental subjective and/or perception methods is: (a) to understand human subjective impressions of the physical characteristics of vibration; (b) to determine the relationship between the subjective perception of some aspect of the vibration and an evaluation index of the physical vibration characteristics; and (c) the establishment of target values for design of vibration environments in terms of human sensation of vibration characteristics. In order to understand the relationship between a physical measure of the mechanical vibration and the subjectively perceived aspect of the vibration environment, experimental methods shown in Table 1 have been used1. [ ] The constant measurement methods of Table 1 are mainly used for measurement of the threshold of human sense. The subjective scaling methods are mainly used for obtaining subjective (or proportional) scaling between the perceived quantity and physical quantity. In this review, the fundamental approach of experimental methods for obtaining the target values used in the design of vibration environments, and the different findings between the subjectively perceived methods for evaluating human response to vibration characteristics and the physical quantity of the vibration environment are summarized. Fundamentals of Subjective Scaling The relationship between the experimental psychological methods for providing target values in the design of the vibration environments and the physical quantities is illustrated in Fig. 1. Vehicle mechanical vibration can be characterized using many metrics, and these can be considered the ‘input’ to the human. In order to predict subjective responses to the vibration, it is necessary to link the characteristics of the source of vibration and human reactions, the ‘output’.

Jan 6, 2006

6889. Aslakson, C. I., and Swick, C. H. Gravity Observations in Peru and Colombia. Coast and Geodetic Survey,-Special Pub. 233, U. S. Government Printing Office, Washington, D. C., 1943, 18 pp. (Price, 10 cents.) In accordance with the policy of cooperation among American republics, the-United States Coast and Geodetic Survey in 1941 made gravity surveys in Peru and-Colombia. The information was desirable for determining the figure of the earth for geophysical purposes and for studying the relationship between intensities of gravity and deflections of the vertical. The survey instrument was the Brown pendulum apparatus. 11 gravity stations were established in Peru and 13 in Colombia. The results obtained at these stations are given in a table covering observed gravity, theoretical gravity, and anamalies. - V. S.

Jan 1, 1943

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

By Albert L. Toenges

(1) The Castleman Basin was investigated by diamond drilling, engineering examination, and geologic study. Agreements permitting investigation of about 14,700 acres of land were entered into with 79 landowners. Eleven beds of coal between the horizons of the Harlem and Mercer beds were penetrated in drilling. These beds from top downward are: Harlem, Upper Bakerstown, Lower Bakerstown, Brush Creek, Upper Freeport Rider, Upper Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Mount Savage, and Mercer. The total estimated reserves of coal (measured, indicated, and inferred), 14 inches or more thick, in six beds follow: [Coal bed: Etimated reserves, tons Harlem _______________________ 23,430,000 Lower Bakerstown _______________ 44, 688, 000 Brush Creek ____________________ 23, 694, 000 Upper Freeport __________________57, 731, 000 Upper Kittanning ________________ 40, 450, 000 Middle Kittanning ______________42,276,000 Total________________________ 232,269,000]

Jan 1, 1952

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By J. S. Megahan

This report covers the design, fabrication and testing of the first and second generation mechanical scaling bars for more safely removing loose rack from mine roofs and walls. Included are discussions covering a survey of mine conditions and presently used hand scaling bar types as well as the design, fabrication and testing of the first and second prototype.

Jan 1, 1982

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen&apos;s original discovery.

Jan 1, 1956

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company&apos;s Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979