Search Documents

By D. Johansson, C. San Miguel, U. Stenman, N. Petropoulos

Blasting is a commonly utilized method in civil engineering projects and mining operations. Ammonium nitrate-based (AN-based) explosives are the most efficient explosives today in terms of handling and performance. However, a side effect is the production of gases. The reduction of these gases plays an important role in the safety and environmental aspects in the working place. Therefore, optimizing the recipes of explosives is vital for minimizing the environmental impact and increasing performance. The aim of the project is to provide results and recommendations on the use of emulsion commercial explosives to support the Swedish mining industry and tunnel-contractors as well as the explosives manufactures. The approach was to test various recipes of civil emulsion explosives to investigate the generation of toxic fumes (CO, CO2, NO, NO2 and NOx) during their detonation. To further increase the knowledge of the influence of different additives, ammonium nitrate prills were added in various percentages. The experimental configuration consisted of magnetite mortar cylindrical specimens with a 50 mm borehole at their center, filled with emulsion explosive. Several tests with different emulsion compositions regarding ammonium nitrate additives (10%, 20%, 25%, 30% and 35%) were carried out in a blasting chamber. The measurement equipment was composed of a flue gas analyzer. The instrument was meticulously cleaned after every test, as well as before and during the tests due to condensation (high humidity and dust) at the inlet of the instrument. The emulsion was manually sensitized with microballons and pumped into the cylinders to ensure lack of bubbles, which could introduce inhomogeneities. The acquired gas concentration data was complemented with temperature, humidity, and VoD measurements. The results showed a linear increase of nitrogen gases as the percentage of ammonium nitrate prills increased. On the other hand, carbon gases had a relatively low coefficient of determination. The VoD data showed a behavior that can be described with a simple quadratic equation.

Jan 1, 2024

By Dr. Anurag Agrawal, Steve Franklin, Clint Zimmerman, Elijah Williams

In a time when data has become a highly valued commodity within many mining and quarry operations, managing large amounts of current and historical information can be difficult. If not managed properly, trying to leverage the data to make informed operational decisions promotes another challenge. Geographic Information System (GIS) is an environment that uses computers and software to create, manage, analyze, and map all types of data. Currently, the mining industry is faced with a challenge to produce the demanded critical metals and minerals that drive our economies. GIS is leveraged in many large mining industries today to help drive decisions, save cost and plan for future operations. Specifically in the Drilling, Blasting and Quarrying industries, data is being captured at many different levels, whether it is a subsurface geological, blast performance, quarry surveys, loading and hauling, or crushing performance. Pen and paper logs and reports compiled lack the dimension that GIS can bring for extracting value from real-time or historical data. GIS connects data to maps, integrating location data with all types of descriptive information. Paired with Artificial Intelligence, additional analytical layers can be built on platforms to extract data and automate workflows. Having the ability to encompass several forms of collected data to drive operational decisions can bring huge savings to the bottom-line. This paper will dive into the areas where GIS data can drive value into operations by assisting in the management and analysis of the types of data being captured, specifically with Drill and Blast. Whether it is tracking haul road conditions, monitoring locations of equipment, environmental conditions, quantifying blast performance or developing a quarry plan based on geological models. GIS can collectively encompass all of this data to bring tremendous value to the operations, improving safety, efficiency and production.

Jan 21, 2025

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By Joseph A. Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project.

Feb 1, 2020

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Sam Taoum, Omar Riahi

Few tools allow for accurately tracking ore dilution after blasting. Existing methods often rely on data analysis or linear interpolation of velocity, which can be imprecise and less effective in varied geological settings. A promising alternative is the use of numerical simulations, which involve complex mathematical calculations incorporating real physical data about explosives and geological characteristics. These simulations can model blast-induced fragmentation and subsequent ore dilution with greater accuracy, providing detailed insights into blast dynamics by considering factors such as explosive type, blast pattern, and rock properties. Numerical simulations integrate data from sources like seismic sensors, blast monitoring equipment, and geological surveys, offering a holistic view that single-method approaches cannot match. By simulating different scenarios, mines can predict the outcomes of various blasting strategies, optimize blast designs to minimize ore dilution, and maximize recovery. Advanced numerical simulations enhance the prediction of fragmentation distribution and size post-blast, crucial for effective dilution control and maximizing ore recovery rates.

Jan 21, 2025

By W. De Graaf, C. Mkumbo

Bulyanhulu Gold Mine Limited (BGML) commissioned a project of sinking a Bulk Air Cooling Shaft during its programme to improve the ventilation system on the mine. As part of this project, a ventilation drift had to be developed and holed into the Main Shaft at 4920 Level. AEL Mining Services (AEL) were requested to provide a technical solution, which included monitoring of blast induced vibrations and to design drilling and timing plans to ensure blasting activities on the vent drift were conducted without disrupting the main shaft’s infrastructure.

Jan 1, 2011

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017

By Andre Koekemoer, Gys Landman

At the moment, electronic initiation is migrating from a position of a specialist niche to that of a more widely applied technology. Ease of use and deployment rate are becoming aspects of greater concern for end users.

Jan 1, 2011

By W. L. Saunders, Richard T. Dana

The dynamites are graded according to the percentage of nitroglycerin that they contain. Thus a “40% powder” would be one in which the sticks, weighing one-half pound each, would include one-fifth of a pound of pure nitroglycerin. Dynamite is usually packed in paper cartridges weighing about one-half pound each which will vary in diameter. When ordering, it is customary to specify a size of cartridge that will as nearly as possible fill the drill hole, the commonest size being 1 ¼” in diameter by 8” in length. It is nearly always shipped in 50-lb. boxes, which have a volumetric capacity of 3/4 cu.ft.

Jan 1, 2013

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025

By Bengt Niklasson

"A test stope at the Luossavaara Research Mine in Kiruna, Sweden,was divided into four different modules in which various hole patterns and explosives were tested in order to evaluate:1. The optimum combination of explosive and hole pattern2. The resulting fragmentation3. The damage to the surrounding rock4. The application techniques of the VCR mining method"

Jan 1, 1985

By Tristan Worsey, John Henchion, Nathan Rouse, Yannick Lauras

"This paper presents an approach used to plan and evaluate drill and blast trials for a mine that currently mechanically excavates in-situ rock. The document presents the approach used to plan the trials, the key performance indicators (KPIs) that were necessary to evaluate the mining methods, the test matrix used during the trials, and the results of the trials. The trials, which occurred as part of an overall drill to mill optimization project at this site, helped to evaluate various blast designs using fragmentation results,drilling and blasting costs, and downstream costs. This project was unique in that (1) drill and blast methods were trialed on multiple rock types and various bench heights using a range of blasthole diameters and powder factors and (2) the load and haul costs were evaluated using a range of loading equipment, from 66 tonne (73 ton) excavators up to 250 tonne (276 ton) excavators. A ten year net cost financial evaluation of the material extraction alternatives was also prepared for the site management. Ultimately, the process of evaluating the drill and blast trials helped the management decide whether to continue extracting using mechanical methods or to introduce drill and blast methods to extract the rock."

Jan 1, 2017

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By Sharon K. Reamer, Klaus G. Hinzen, Brian W. Stump

"This study investigates seismic wave propagation from two production shots in a limestone quarry. Our motivation is to investigate the efficiency of two superpositioning techniques. The production shots consisted of an 18 and 20 hole explosive array detonated in a single row with constant delay times of 32 and 20 ms, respectively. A single shot was fired on a neighboring part of the quarry bench. The experiments were instrumented with 20 three component seismometers (35-120 m range). The computer-controlled electronic firing system resulted in firing time deviations of less than 1.4% of desired fired times. Linear superpositioning with the observed single shot data produces seismograms which adequately reproduce temporal effects of the multiple explosions; however, spatial effects due to the extended source length (68-76 m) are not modeled with this method. Linear superpositioning with individual half-space Green's functions for each explosion in thearray convolved with a calculated Mueller-Murphy source produces seismograms which match the time duration of the observed production shot seismograms and differ in absolute peak amplitude by less than a factor of three. Parameter estimation for the source is taken from chemical explosion study results. The single source model differs in amplitude from the observed single source seismograms by a factor of 2.3."

Jan 1, 1991

By Scott Stephenson

Making a tunnel through solid rock can sometimes be a dangerous task. Many things must be considered in order to complete such a task safely, and efficiently. Prior to starting things must be known such as, the type of rock, the purpose for the tunnel, the destination point, then angle of decent (or ascent). Once these things are known, the method to proceed must be considered. Factors such as cost, feasibility, and time to completion must be taken into account.

Jan 1, 2009

By Selamawit Asfaw, Mohamad Sharif

In recent years, the use of modal analysis has increased to include many different aspects of the construction industry. Computer modal analysis can be used in determining the dynamic properties of a structure by mathematical equations and knowledge of the structure’s physical properties. This technique can now be used to predict the level of vibration induced by blasting on adjacent structures. Ground vibration induced by buried explosives is a major concern for contractors when excavating near utility pipelines such as gas and water lines. The size limitations placed on easements causes the necessity of additional utility lines to be placed in close proximity to existing lines. Through the development of computer models of the pipe, stress analysis can be performed prior to blasting. Based on the calculated dynamic properties (natural frequencies and modal shapes) and the maximum allowable displacements and stress levels (which are established by the pipe manufacturer) the allowable maximum charge weight per delay can be selected for the blast. The selected maximum charge weight per delay will ensure that the resulting pipe peak particle velocity level is within 95% confidence. This means, statistically, there exists a 95% probability that the actual pipe peak particle velocity would be less than the predicted value. The pipe is then instrumented with vibration measuring sensors to ensure that vibration levels are within the allowable maximum pipe strength. In conclusion, this technique can assist the engineers and blasters, to establish the proper blast design. It allows for safe and efficient installation of additional utility lines adjacent to existing lines. This technique can also be applied to predict the structural response to blasting induced vibration for a variety of complex structures. A detailed explanation of this technique, as well as an example of application including formulas used for this technique will be provided in this paper.

Jan 1, 2000