Search Documents

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By E. Vahidi

In this study, a hydrometallurgical treatment involving solvent extraction of zinc using D2EHPA (di-2-ethylhexyl phosphoric acid) has been investigated to recover zinc from an industrial zinc leach residue. The residue was leached with sulfuric acid producing leach liquor which was subjected to solvent extraction for enrichment of zinc and removal of impurities. Operating variables for the zinc extraction process, such as pH of the mixed solution (0.5~5.0), concentration of D2EHPA (5%~40%, w/w), temperature (25~60°?C), A/O volumetric phase ratio (1/2~4/1), concentration of tri-butyl phosphate (TBP) as modifier (3%~7%, w/w), concentration of NaR2RSOR4R in aqueous phase (0.05M, 0.1M, 0.2M) were also studied. Practically all zinc was extracted from the aqueous solution at pH 2.5 with 20% w/w D2EHPA in kerosene. At this operating condition, zinc could be extracted at one theoretical stage at A/O phase ratio of 1/1, as calculated by the McCabe-Thiele method.

Jan 1, 2014

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By Alan Bye, Nick Beaton, Wayne Stange, Emmy Manlapig, James Groutsch

"For over 50 years the JKMRC has applied a unique education-based research strategy to develop modelling and simulation tools that are "fit for purpose" for industrial application. These tools are widely used for the analysis and optimisation of mining and mineral processing systems. As the mining industry context evolves to deal with declining head grades, falling commodity prices, professional skill shortages, and an exponential growth in the volume of data, a re-evaluation of what "fit for purpose" means in the future is required. It is contended that future industry needs for simulation-based decision support requires tools and systems that incorporate: • Multi-component modelling, • Models of complex sensor behaviour, • Integration across the physical value-chain e.g. resource to market, • Financial analysis including risk and uncertainty assessment, • Enabling multi-criterion decision making (technical, financial and environmental), • Ore-body knowledge at multiple scales, • The use of fundamental numerical models to provide insight for the development of practically useful models, and • Decision support delivered through remote operations centres. JKMRC and CRC-ORE are collaborating to develop a next-generation simulation-based decision support system that assists in addressing these challenges. The Integrated Extraction Simulator (IES) combines many years of pragmatic and successful work integrated with modern technology trends - in particular the rapid move to cloud-based computing."

Jan 1, 2014

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By D. I. Verrelli

Within the flotation community a belief has developed that some particle shapes are more ?floatable? than others. This is usually attributed to an influence of particle shape or roughness on the induction period required to achieve attachment between the particles and the air bubbles in the pulp. Up to now, such measurements have not been able to readily isolate the effect on individual flotation subprocesses. In contrast, our experimental apparatus, the CSIRO Milli-Timer, enables us to directly observe the process of particle?bubble interaction and attachment by means of a high-speed video recording, thus providing a direct measure of the induction period for attachment. To assess the influence of particle shape on induction time we used two varieties of methylated borosilicate glass particles ? spheres and angular ?frit? ? in a range of tightly-sized fractions. In doing this, we take care to account for the influence of other factors that could affect the induction time, such as the polar angle of sliding commencement, and approach velocity. These parameters are recorded as variables for each interaction, and corrected for using multiple nonlinear regression. Our results illustrate the importance of particle shape on induction period, with angular particles exhibiting induction periods that were an order of magnitude lower than those of spheres. Furthermore, the induction period was seen to decrease with increasing particle velocity, or kinetic energy on approach, but increased as the trajectory approached the limit of just grazing the bubble. Particle shape in mineral processing is a consequence chiefly of the mineral type and the type of grinding employed. The results presented herein indicate that attention should be paid to the shape of particles obtained from the grinding operation, besides particle size. Keywords: attachment, bubbles, flotation, induction period, particles, shape effects, surface roughness

Sep 1, 2012

By Kari Niiranen, Patrick Krolop, Viktoria Töyrä

Luossavaara-Kiirunavaara AB (LKAB) operates an iron ore mine, three beneficiation plants and three pelletizing plants in Kiruna, Sweden. The current methods of separation in the beneficiation plants are wet low intensity magnetic separation (WLIMS) and reverse apatite flotation, where the WLIMS stage is regarded as the crucial part of silica separation from the ore. Currently, the high-grade iron ore deposit of Kiirunavaara has a low grade of silica in situ, of approximately 3.0% SiO2, but the silica grade is expected to increase in the deeper parts of the deposit with a complex silicate mineralogy. An increasing silica grade will affect especially the production of direct reduction pellets (LKAB DR Oxide Pellets), one of the main products of LKAB in Kiruna with an average silica grade of under 0.75% SiO2. The silica grade in the magnetite concentrate is normally limited to a maximum level of 0.55% SiO2 in order to achieve the required chemical composition in the pelletizing process. In order to study the possibility to reduce silicate content in the magnetite concentrate (pellet feed) in the beneficiation plants in Kiruna obtained by wet low intensity magnetic separation (WLIMS), enlarged mineral processing test work was carried out in the LKAB’s mineral processing laboratories in 2016. The test work consisted of comminution, low intensity magnetic separation and reverse cationic silicate flotation at laboratory scale, complemented by screen analysis, chemical assays and mineralogical investigation. The results of these mineral processing test work showed that the magnetic separation is not sufficient to reduce the silica content in the magnetite concentrate, particularly in the case of the high-SiO2 ore type B2-a. The reverse cationic flotation can be regarded as a possible solution to reduce the silicate content in the magnetite concentrate obtained by WLIMS and to achieve the required silica grade of less than 0.55 % SiO2 in the pellet feed. The results of this study provide a good basis to understand the behaviour of different silicates in the existing beneficiation process. Furthermore, it serves valuable information for development of new beneficiation processes and for investment in new equipment at the beneficiation plants in Kiruna in the future.

Jan 1, 2018

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014