Search Documents

By Andrew E. Grosz

The United States is dependent on foreign imports for about 80 percent of its ilmenite, about 60 percent of its rutile, and virtually all of its monazite. Nearshore marine sand deposits and beach-complex sediments in the southeastern United States are important domestic sources of ilmenite, leucoxene, rutile, zircon, monazite, and a number of other less well known economic heavy-mineral (HM) species. Because global onshore reserves of placer titanium minerals may fall short of demand in as few as 20 years, offshore research in HM placers will become more important. The Atlantic Continental Shelf (ACS) defined by the shoreline and the 200-m isobath varies in width for the modern U.S. coastline from a fraction of a kilometer to about 150 km offshore of Cape Cod, Mass., and includes an area of about 3.91 x 105 km2. It probably contains 3-7 x 1011 m3 of sand and gravel which may locally contain commercially exploitable placer HM deposits.

Jan 1, 1986

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By Peter E. Halbach, Andreas Jahn

Co-rich hydrogenetic ferromanganese crusts are typical marine interface products of growth processes taking place on sediment-free substrate rocks on the seafloor. They grow very slowly and preferentially in water depths below the oxygen-minimum zone (OMZ) and have so far been found even in water depths of up to more than 5000 m, i.e. also below the calcite compensation depth (CCD); these deep ferromanganese crusts are particularly rich in Fe. It is assumed that the O2-minimum zone is the most important source layer of dissolved manganese, the decomposition of fecal pellets here also contributes to this Mn-budget. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical as well as a surface-chemical mechanism. Microbial mediations can be assumed, in particular since steps of redox-reactions are involved. The two main components of the hydrogenetic substance are hydrated d-MnO2 (vernadite) and x-ray amorphous Fe-oxyhydroxide, both of which are intimately intergrown with each other forming the extremely fine-grained hydrous oxidic material. In seawater, elements occur as dissolved hydrated ions or as inorganic as well as organic complexes which, in general, have either a positive or a negative surface charge depending on the pH of the respective marine environment. These complexes form hydrated colloids that interact with each other or with other dissolved hydrous metal ions. The main agent to oxidize the dissolved Mn2+ ions is oxygen, transported upwards from deeper water by turbulent eddy diffusion and turbulent rise processes at seamount slopes.

Jan 1, 2017

By S. W. McCandless

Since the mid 1970's, the science of remote sensing has invented and demonstrated sensors that hold unique promise for users that operate in the marine environment. Earlier, visible and infrared sensors provided images and temperature maps of surface conditions, but the 1970's introduced active (radars) and passive (radiometers) microwave sensors capable of penetrating clouds and operating day or night over the world's oceans. Space-based observation satellites permit these systems to span the globe many times each day, providing a view of the world's oceans and Arctic areas consistent with daily and, sometimes, hourly changes in the marine environment. Experimental satellites launched by NASA proved that such systems had great scientific merit, but, even more importantly, they could produce information valuable to marine transportation, fishing, and resource exploration and extraction. This latter subject includes the off-shore search and production of petroleum and natural gas resources and ocean mining as well. A few early satellites, such as GEOS-3, Nimbus-7, and most notably Seasat established that global wind fields, all weather sea surface temperature, ocean topography and sea state, and fine scale images of wave patterns, surfactants,

Jan 1, 1986

By Jae-Hyung Park

Since the Industrial Revolution, the land resources have been decreased rapidly as the industrialization. And this phenomenon brings to our mind an interest in deep-sea resource(manganese nodule). Hence, Korea has been participated in the development project of exploiting manganese nodule since 1983. Hwang and cho(1998) studied the economic efficiency evaluation of manganese nodule carrier. But they used the TAMU(Texas A&M University) model, and assumed deadweight and velocity of bulk-carrier. If we use some optimization technique, more economic manganese nodule carrier can be selected and evaluated without limited assumption. In this study, we evaluated the economic efficiency of manganese nodule carrier using genetic algorithms(GAs).

Jan 1, 2003

By Arturo Carranza Edwards

One hundred ninety nine beach face sand samples from an equal number of beaches from the Mexican Pacific were studied. Based on petrological and chemical analysis some locations have been studied in more detail. Black sands from the following areas are discussed: (1) west Baja California Peninsula, where black sands rich in magnetite and ilmenite have maximum values of 50% iron and 14% titanium in the very fine sand fraction; (2) east Gulf of California, in its northern portion, the black sands show maximum values of 43% iron and 5% titanium in the fraction 2 to 4 0;-(3) the south Mexican Pacific, characterized mainly by medium sands, moderately well sorted, show that the fine sand fractions reach values of 35% iron and 41% titanium. X-ray fluorescence applied on selected samples constituted by feldsarenites and lithic feldsarenties, showed the presence of rare elements in some of the studied samples.

Jan 1, 1994

By Georgy A. Cherkashov

Two principal types of the hydrothermal fields in Atlantic - axial and off-axis - could be established based on their structural setting in the rift zone of the Mid-Atlantic Ridge (MAR) (Figure1). The first (axial) type is represented by five high- and three low-temperature hydrothermal sites (Table 1). All of these fields are connected with young axial effusive volcanism and related to large linear volcanic ridges or central volcanoes at the inner floor of the rift valley. The hydrothermal activity here is controlled by the intersection between longitudinal magma feeding faults and transverse weakened zones characterized by high permeability. [ ] The hydrothermal sites of the second (off-axis) type (such as Rainbow, TAG, 24°30?N, Logatchev, newly discovered 13°N (Figure 2) and possibly 16°48?N sites) are related to large tectonic dislocations forming marginal scarps of the rift valley as well as transverse discontinuities.

Jan 1, 2003

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

By Wonn Soh

As for Earth, where human beings live, approximately 70 % of its surface is covered by oceans. Today, advanced technology has led us to understanding the abyssal ocean floor through the use of submersibles and ROVs (remotely operated vehicles) for the last 30 years. Furthermore, the oceanic crust beneath the abyssal floor still remains an unexplored scientific frontier due to the lack of a direct approach. Exploration of this frontier is required to enhance our understanding of the mechanism of the M.8 class plate-subduction-type earthquake, of generation of the big tsunami, that caused the disaster, and of the paleo-global environmental change as well as of the origin of life as viewed in deep water thermal vents.

By Winston Rocher Anda

Traditionally, mining activities have been developed in firm land, but technological advances and human needs have opened in the last year?s new opportunities in the maritime field. This has happened not only in the oil or hydrocarbons industries, but also in relation to the exploration or exploitation of other minerals, metallic and non-metallic. This has forced several countries to complement or create legal rules that make possible its own development and the International Law, through the United Nations Convention on the Law of the Sea, to regulate this activity in the space of its own, the calling area. Chile, as country with a long experience in mining and great advances in large deposits exploitation, possesses a special juridical frame that regulates this economic activity according if it is the geographical or territorial area in which is realizes, and it has been complemented lately with the international normative.

Jan 1, 2011

By David G. Jones

Radiometric surveys of the beach and nearshore zone of the Dutch Frisian Islands have identified sands enriched in heavy minerals. The areas of heavy mineral concentration have been mapped in detail using a state of the art towed gamma-ray detector, which gives improved sensitivity through the use of new detector materials and improved data processing techniques. The detector provides continuous measurement of sea floor radioactivity (and of a number of other parameters) and can be used simultaneously with other survey techniques, such as echo sounding, sidescan sonar and shallow seismic profiling. It enables a rapid, and cost effective, assessment of the surface distribution of heavy minerals to be made. The heavy mineral suite includes magnetite, ilmenite, garnet, rutile and zircon. These minerals contain 1-3 orders of magnitude more U and Th, in terms of their activity concentrations, than the accompanying light minerals (mainly quartz). Since the heavy mineral composition of the sands appears to be relatively constant along the Dutch Frisian Island chain, the U and Th concentrations can be used to provide a quick estimate of the heavy mineral content. The sea floor radiometric measurements allow sediment sampling for more detailed analysis to be highly targetted. The zones of heavy mineral enrichment are generally sub-parallel to the coast and are usually confined to water depths of 5-10 m. There is a close correlation with sand bars on the shoreface, the highest radioactivity typically occurring just seaward of the crest of these features. As well as being used for heavy mineral exploration, similar radiometric methods can be applied to mineral processing. Gamma-ray detection systems can be used to provide rapid analysis in the process stream enabling on-line grade control and optimisation of processing, from excavation of mineral sands to the final products.

Jan 1, 1995

By James R. Herring

An unusual combination of ten new, deep (-100 m) coreholes and an extensive high-resolution seismic reflection network enables us to produce a detailed study of the phosphorite resources in the Tertiary strata of the Georgia continental shelf. These strata are mixtures of a terrigenous facies, notably quartz and clay along with minor amounts of other aluminosilicate minerals, and of a marine facies, notably phosphorite and carbonate. Phosphatic sediments occur throughout the cores, however the richest phosphorite beds are in the middle Miocene (Serravallian) sediment, where they constitute up to 70 percent of the sediment mass. Major zones of phosphate enrichment occur chiefly at major unconformity boundaries (tops of Oligocene, lower and middle Miocene, upper Miocene, and lower and upper Pliocene) and at prominent intrastratal reflectors representing minor unconformities within units. Phosphorite co-occurs with the clay minerals, especially palygorskite, but correlates inversely with carbonate and detrital quartz, indicating a low-energy depositional environment. The clay minerals present in these strata, which have an environmental consequence on recovery of the phosphorite, are varying concentrations of smectite, kaolinite, mica, palygorskite, and sepiolite. Phosphatic resources have been determined within only the Miocene strata. Sediment volume for this unit to the 100 m isobath on the continental shelf has been established using the high-resolution seismic reflection network that has been calibrated using the deep coreholes. Phosphorite grains larger than 0.1 mm average about 40% of the sediment. In turn, most of the remainder of the sediment in this size range is quartz, which is separable from phosphate grains using conventional flotation techniques. Our estimate is that 300 Gt of phosphorite lie within the Miocene strata of the Georgia continental shelf.

Jan 1, 1994

By Virginie Tilot

Recommendations have been drafted following an international multidisciplinary panel discussion organized at UNESCO/IOC by the Académie des Sciences d?Outre-Mer on 15 December 2010 conveyed, according to its mandate, to the French government and to an international pool of scientists and stakeholders. These take into consideration the relevant Provisions of the United Nations Convention on the Law of the Sea of 10 December 1982, the Rio ?Earth Summit? Convention of Biological Diversity of 5 June 1992 as well as the activities and recommendations implemented for the world?s oceans and seas, in particular by the International Seabed Authority (ISA) and the recent reports and scientific works (including those implemented by the ISA Kaplan, Ifremer, COI-Unesco). The recommendations integrate, for one of the ecosystems, the conclusions of the project of the conclusions of an IOC-UNESCO / Government of Flanders project (2004-2010) implemented by Dr. V. Tilot from 2004 to 2010, during which were published three volumes describing the referential state of the polymetallic nodule ecosystem and proposing options for the management and conservation of the nodule ecosystem in the Clarion Clipperton Fracture Zone, NE Pacific Ocean: http://unesdoc.unesco.org/images/0014/001495/149556f.pdf, http://unesdoc.unesco.org/images/0014/001495/149556e.pdf; http://unesdoc.unesco.org/images/0014/001495/149556e.pdf#223

Jan 1, 2011

By Michael W. Milner

Cold Ocean Placers: Polar storms, interstadial littorals and crustal adjustments. Polar storms with consistent strong winds in the Southern, Antarctic Ocean are responsible for placer deposits on both the east and west coasts of Australia, on the west coast of New Zealand, as well as on the coasts of South America and Africa. Arctic winds, confined by both land and ice, generate similar placers in Labrador and Greenland as well as on the coasts of Scotland, Norway, Hudson's Bay, Nome, Goodnews Bay, Kamchatka and the north coast of Siberia. Tasman and Labrador seas have several parallels to Newfoundland, including north-south polar waterways, young spreading ocean floors, and youthful coastal escarpments with glaciated coasts. Black sand beds in beach deposits on the modern and Pleistocene transgression strandlines, skewed to the distal ends of beaches, and set into either bedrock or sediment fill, are the locus of the light-heavy mineral placers with titanium, zirconium and rare earth elements; chromium; iron; and tin. Gold and platinum group elements are the ultra heavy minerals at one end of the spectrum and tend occur in proximal placers generated, either directly from bedrock sources, or as minor by-products in distal light-heavy mineral placers. Diamonds are unusual in that the value is only in the larger stones, despite the formation of beach sand and aeolian placers in the littoral zone, and the sites of concentration are in very high energy bedrock traps, on terraces that are mined to depths of 100 metres below sealevel.

Jan 1, 1995

By Yannick C. Beaudoin

Southern Explorer Ridge (SER) is an anomalously shallow, intermediate-rate spreading ridge located 200 kilometers off the west coast of Vancouver Island, Canada. It ranges in depth between 2600 m (deepest basins) and 1760 m (bathymetric minimum). At least 60 sulfide deposits are known to be associated with hydrothermal vent fields along the ridge. For the first time geological data, including deposit locations, collected from 15 marine expeditions to SER since 1983 have been assembled in a GIS format. GIS processing techniques were employed to plot the distribution of base metal concentrations for recovered sulfide samples. The highest base metal concentrations are found in the vicinity of the Magic Mountain site (main active vent field), and also proximal to a side scan sonar anomaly referred to as AGOR 171. Individual samples near these locations have yielded values as high as 29.3 wt\% Cu, 34.3 wt\% zinc, 0.97 wt\% Pb, 2.0 ppm gold, and 664 ppm silver. Sample paucity is the key limiting factor that prevents adequate assessment of the areas economic potential.

Jan 1, 2001

By Richard Petters

Williamson and Associates, Inc of Seattle, Washington has recently built a remotely operated seafloor coring system for Nichiyu Giken Kogyo Ltd and the Metal Mining Agency of Japan (MMAJ). The system is designed to core to depths of 20 meters in 6,000 meters of water and will be operated from MMAJ's research vessel Hakurei-Maru No. 2 The corer uses rotary rod coring methods and will recover a core diameter of 44 mm. To facilitate coring through soft or unstable formations, the corer has the ability to set casing. The corer is fitted with thrusters for positioning during landing and telescoping legs for leveling. The system is operated through a 12 km electro-optical cable. Data displayed to the operator provides the operator with real-time feed back and control over the coring process. The operator has independent proportional control over bit weight, advance rate, rotary speed, and flushing water flow. The process of making up, breaking down and storing the drill string is automated and is controlled by a logic driven software routine. The system is currently undergoing trials in Japan. This presentation will discuss the drill's capabilities and should be of interest to those in need of a tool for assessing the thickness of marine mineral deposits.

Jan 1, 1996

By Alexander Malahoff

Six active Kermadec Arc submarine volcanoes located between 34°S and 36°30?S were mapped and sampled by an interdisciplinary inter-institutional research team between April and July 2005 using submersibles Pisces V and Pisces IV aboard the mother ship the RV Kai?mikai-O-Kanaloa. The purpose of the expedition was to study the relationship between hydrothermal activity, formation of hydrothermal mineral deposits and the biodiversity of life associated with the hydrothermal vents. Of the volcanoes examined, all showed evidence of hydrothermal activity, plume production and helium anomalies. Only two of the volcanoes, namely Brothers and Clark, showed chimneys and surficial poly-metallic sulphide deposition. Hydrothermal venting at a water depth of 1700 meters within the base of the northern wall of the summit caldera of Brothers Volcano has produced a field of chimneys, some of them 5 metres high with black smokers venting. Temperatures of 300°C were measured within the active vents. Clark Volcano has a double cone summit at a water depth of 875 metres. The shallowest cone has a near-summit hydrothermal vent field with 5-meter high venting chimneys and smaller structures around the periphery. Water temperatures of 200°C. Geochemical and petrological analysis of the massive poly-metallic sulphide samples taken from Brothers and Clark show a diversity of mineralogy. This diversity is clearly a function of hydrothermal water temperature. Chimneys sampled from Brothers are pyrite and sphalerite dominant with lesser chalcopyrite. Sulphides from Clark Volcano tend to be barite rich with lesser sphalerite and pyrite. Sulphides from Brothers Volcano have a range in gold composition of 4 to 58 ppb with silver composition of up to 38 ppb. A mineral formation model for the volcanoes suggests hydrothermal fluid boiling within the volcanic edifice for those volcanoes with shallow summits and massive sulphide deposition with the edifice as well. Surficial deposits include native sulphur and lower temperature oxides. Only the deeper water Brothers Volcano shows massive sulphide deposition along the marginal faults of the caldera floor.

Jan 1, 2005

By Wilhelm Schwarz

Manganese nodules lay in vast areas of the deep sea floor. Ideal harvesting conditions for a manganese nodule field are dense nodule abundances of nodules between 20 and 60 mm diameter and a metal content as high as possible. With regard to the development of collector technology, the properties of the deep sea soil, in which the nodules are embedded and to which the nodules stick, are of major interest. The forces for loosening the nodules have to be provided by the collector. For this purpose water jets and/or mechanical devices can be employed. For the choice of the best collecting procedure, various criteria, such as collecting rate, energy consumption and the environmental impact on the eco system of the deep sea floor, have to be considered and weighted as to their importance. Nowadays, the concept of a mining system with a flexible transport hose and a self propelled collecting machine is increasingly accepted among the expert community. With regard to the trafficability of the deep sea soil with a self propelled mining machine, the mechanic properties of the soil and the morphology of the deep sea floor are of special importance. The manganese nodule fields, which are interesting with regard to their recoverability, are mostly in the areas of tectonic fracture zones, at which the morphology of the sea floor is formed by vulcanic activities. In these areas, deep sea mountains, pits and other obstacles exist that have to be driven around if not trafficable.

Jan 1, 2003

By Charles L. Morgan

For the past twenty years or so the oceans of the world have been transformed in the minds of most Americans from the ultimate and nearly infinite receptacles for sewage and other wastes to an almost sacrosanct and threatened last refuge of Mother Nature from man on Earth. While this general movement has helped somewhat to moderate the flows of pollutants into the oceans, it has had severe and sometimes devastating impacts upon various attempts to develop seabed mineral resources. Marine mining proposals have been easy targets for attack. In most cases, they have short or no histories and involve prototype or first-generation methods. They commonly lack major financial backing, and do not command significant public support. Their constituents are limited. Opposition movements to such proposals have been able to evoke strong support by appealing to this "last refuge" image and depicting mining operations as the final assault. In mounting these public appeals, the movements obtain visibility and support. Because of the small and sometimes tentative status of the constituencies which support particular proposal s, the potential liabilities for opposition movements are minimal.

Jan 1, 1989

By Andrew Bellamy

A thorough appreciation of the origin, formation, preservation and geometry of marine sand and gravel deposits is central in demonstrating that their extraction by dredging does not affect coastal processes or marine life. Geological evaluation underpins wave, tidal and sediment transport modeling and assists in predicting the nature and extent of seabed change during and after dredging. Marine sand and gravel deposits in the English Channel, southern North Sea and parts of the Irish Sea are of predominantly periglacial fluvial origin and record long histories of valley and floodplain cut and fill associated with Quaternary climatic and sea level oscillations. In the Bristol Channel, the influence of marine transgression and tidal dominance in sorting proglacial outwash deposits is evident in the distribution of sandbanks, scoured channels and gravel lags of this region. These deposits are relict and are unrelated to coastal sediment dynamics. Their extraction leaves seabed depressions which monitoring shows remain unfilled. The resultant offshore bathymetric changes and sediment removal in over 10 m water depth are not transmitted to the coastal zone as beach drawdown, wave height increases or sediment starvation. Applications for new aggregate dredging permissions in UK waters must be accompanied by an EIA and need to make a convincing case that the dredging will not affect rare or declining species and communities of marine life. Seabed recovery rates post dredging are now investigated and understood with reference to geological setting and the uniqueness of the sediment/biological character (biotope). Investigation of the continental shelf by the Industry and others reveals the large extent of gravel-dominated biotopes relative to commercially viable deposits.

Jan 1, 2004