Search Documents

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

Jan 1, 1987

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By J. Nakayama

Construction of foundation piles or diaphragm walls through rocky or boulder containing formations has been long-standing difficulty. It has been widely understood that the down-the-hole hammer is the most capable mechanical means but is restricted in drilling diameter by the unavailability of drillhead sufficiently large diameter and the difficulty of disposal of cuttings. A great number of submersible motordrills have been used for the construction of cast-in-place piles and diaphragm walls and the reverse circulation system employed has demonstrated its advantage of the prompt removal of cuttings. The development of multi-head down-the-hole hammer drill combined with reverse circulation system presents a powerful engineering choice for those "hard-to-drill" ground formations. This paper will introduce the features of the system and some actual operation results in the foundation engineering through those hard rocky ground formation in some countries.

Jan 1, 1989

By Suk han Jang

This paper describes the tower foundation design and construction experience for the 345kV Youngheung marine transmission line, which has been in commercial operation in Korea since July, 2004. This transmission line was designed and constructed to meet the rapidly increasing power demands of metropolitan areas and supply stable, bulk electric power from the Yonghung thermal power plant into metropolitan areas. This transmission line passes over the west sea, Lake Sihwa and over land. In order to successfully complete this project, and to safely support the tower during severe maritime conditions, several types of tower foundation such as Pad and Chimney foundation, Pier (Cylindrical) foundation, R.C.D foundation, Jacket pile foundation and Steel pipe pile + concrete mat foundation were developed and used. As the world?s first and longest marine transmission line, the 345kV Yonghung marine transmission line operates successfully, thanks to several high-tech civil engineering technologies and KEPCO?s accumulated experience.

Jan 1, 2007

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Almer E. C. van der Stoel

"Abstract This paper deals with assessing the bearing capacity of existing wood pile foundations. With a wide range of restoration projects being performed in the Netherlands, on many locations deep excavations need to be constructed next to existing, many times listed buildings. The building are founded on piles that are often centuries old, so a close evaluation of the remaining bearing capacity, combined with and assessment of the influence of the excavation is in place.After giving an introduction on Dutch pile foundations, a methodology is described to assess the bearing capacity. Aspects as physical foundation investigation, determination of the current bearing capacity and a calculation of the bearing capacity in the new situation are discussed. The results of both analytical and Plaxis calculations are outlined, focussing on how to practically use this approach in renovation projects. Finally, cases studies of the successful application of this approach in major renovation projects in Amsterdam, such as the Conservatorium Hotel and the New Rijksmuseum are used to illustrate the successful application of this approach.A Short Dutch Pile Foundation History (based on Van der Stoel, 2001)The first houses built in Amsterdam, in the 12th century, were very light constructions of timber without foundations. Because of the soft peat layers found in Amsterdam, the houses there suffered from damage due to settlement. In the 13th century, castles and churches were increasingly built of bricks, which made it necessary to provide support for bigger loads. Under the wall of the construction a trench was dug, and this was filled on either side by alder fascines. Between the fascines small wood piles were driven (by hand) on which another series of fascines was put. On top of this construction, were placed oak slabs on which the bricks were then laid. From that moment on, a problem was caused by the decay of wood foundation elements in the humid soil. In 1503 a law was introduced forbidding building foundations on public streets without permission of the Building Inspection (to keep the fronts of the buildings in a straight line). In 1528 a law requiring permission from the local authorities for all building activities replaced this law. In this period developments started which led to the use of the type of foundation that can be considered the mother of the current “typical” Dutch pile foundation. The piles used in this period were shaft- bearing piles about 5 to 7 meters long. The mostly pine piles were driven between oak beams, which were placed on either sides of a trench, after which other oak beams were laid across at regular spaces: the so called “pile bent” pile foundation (Figure 1)."

Jan 1, 2014

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

By Zachary Q. Maassen

The purpose of this paper is to highlight the environmental benefits of properly managing slurry waste as it is generated on site. The following projects will be used to illustrate the importance of proper onsite waste management. Project: Jet Grout Backflow Dewatering The goal was to dewater the backflow directly onsite to produce a dry, solid waste and reusable water. The backflow spoil was pumped directly to the dewatering system as it was generated. Utilizing mechanical separation equipment and flocculation polymer the waste volume was reduced by 44%. Due to the site footprint and high volumes, slurry waste removal and onsite processing were the only two feasible options. Onsite dewatering proved to be the environmentally beneficial option as it eliminated the need for slurry waste hauling and disposal. The benefits of utilizing a dewatering system are listed below: Project: Soil Mixing Spoil Recycling for Slurry Wall Construction In this application the spoils generated contain bentonite mud, cement mixture and organic ground soils. The goal of this project was to process the backflow mixture to recover reusable bentonite mud and separate the soil as a dry, stackable waste product. The treatment system replaced the traditional method of vacuum truck extraction and facility disposal. The environmental benefits of properly handling the backflow is a decrease in fresh water usage, bentonite additive reduction, and the reduction of CO2 emissions. The paper will consist of a project scope, technical equipment and process description, environmental impact reduction calculations and lessons learned for each project.

Jan 1, 2018

By Helen D. Robinson

The seawalls that surround Ellis Island were constructed in the early 1900s and now show varying degrees of deterioration. An innovative approach to the structural repair of the seawalls was developed, which consisted of the use of micropiles for stabilization of vertical and horizontal seawall movements. The micropiles were installed through the existing seawalls and penetrated through a thick overburden, consisting of soft alluvial deposits and relatively hard glacial till, and were bonded into Manhattan Schist. Drilling of the micropiles often encountered timber and other obstructions. The selection of micropiles for stabilization of the seawalls offered significant advantages over other foundation systems and over alternative soil improvement techniques. They allowed drilling through a variety of materials without the need for significant retooling or changes to the drilling procedure. This reduced the impact of foundation construction on the sensitive historical landscape and structures, and prevented the need for significant foundation work from the water side of the seawalls. In addition, micropiles offered relatively high installation rates and flexibility to adapt to the varying conditions along the seawalls.

Jan 1, 2008

By Alexander J. Verstraeten

The design and construction of foundations for power transmission line towers present some special problems. This paper describes a system of design and construction for these foundations that was developed in Europe and has attained general use there because of its reliability and cost effectiveness. Transmission line foundations distinguish themselves by having to deal not only with compressive and lateral loads, but with uplift loads and, because of the wind (in some regions earthquakes), with dynamic loading. The construction of transmission line foundations distinguishes itself mainly in the great number of inaccesible locations involved, resulting in extensive geotechnical investigation and logistical problems in moving men, materials and equipment.

Jan 1, 1987