Search Documents

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By C. C. Walden, A. Bruynesteyn

"Chemical and biological aspects of the formation of acidic effluents from sulfide waste materials are discussed. Test procedures to determine the acid producing potential of waste materials, as well as the characteristics of such acidic effluents, are presented. Practical applications of the test procedures are discussed with reference to predictior of environmentally unacceptable drainage and to estimation of metal recovery by dump leaching.INTRODUCTIONNatural leaching of sulfide minerals, exposed to the atmosphere, has been occurring for geological time. For centuries, man has been aware of the acid drainage originating from coal workings, copper mines and waste dumps. With the advent of the technical sciences, the processes involved in acid mine drainage production were considered to be solely chemical in nature. However, in 1947, it was shown (1) that a specific microorganism, called Thiobacillus ferrooxidans, was responsible for acid mine drainage from coal workings. It was demonstrated that under suitable conditions - this bacterium oxidized pyrite and marcosite in the coal to ferric sulfate and sulfuric acid. Numerous studies have subsequently demonstrated that - under suitable conditions - Thiobacillus ferrooxidans can attack most sulfide minerals, producing weak sulfuric acid, oxidizing ferrous to ferric iron and solubilizing other metals present (notably copper and zinc) as their sulfate salts."

Jan 1, 1980

By L. H. Michaud

"Albian Sands Energy (ASE), an oil sands surface mining and extraction operation, is currently undergoing start-up and is scheduled to ramp-up to full production by mid-2003. Startup includes the selection and implementation of over 75 IT systems or computer applications which include: engineering applications; systems required to control mining activities, maintenance, the processing plant and utilities; and also systems required to run the company, such as human resources, finances and inventory/ warehousing.This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in ASE’s approach to identifying system requirements is the development of a business activity model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been led by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that do not meet the company’s expectations. To ensure a more positive outcome, ASE believes that it is imperative that the company’s technical and business people be closely involved in the selection process.Integration of the IT systems is also key, including linking all applications through a data warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company"

Jan 1, 2003

By J. Lazareck

"XPotential Products Inc. has developed technologies to convert auto shredder residues and other forms of plastic waste into useful products such as posts suitable for retaining walls and parking curbs. The technology is competitive provided low-cost plastic waste is available, and could have applications throughout the world. The paper describes the technology used and illustrates the various processing steps. Development of the TechnologyPresently, state-of-the-art auto shredding yields approximately 75% ferrous and non-ferrous metals and approximately 25% by weight of auto shredder residue (ASR). Advances in metal shredding and non-ferrous metal separation technologies turned XPotential Products Inc.’s attention to ASR as a potential revenue source, or at least a means to markedly reduce the cost of disposal. This abundance of nuisance ASR was, in the company’s view, a potential resource as derelict autos and white goods were similarly perceived 40 years ago. As owners of General Scrap & Car Shredder Ltd. in western Canada, XPotential faced significant disposal costs for four shredders. This journey began over 10 years ago and took many twists and turns until a final course of action was chosen. The recovery of the metallic portion of vehicles and white goods has reached technological maturity and attempts to add value are now achievable only in very small increments."

Jan 1, 2004

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By G. E. Norman, J. F. Jackson, A. L. Mckague

"The treatment of nickel-copper concentrate in the new smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, is described. The concentrate in a slurry form is partially roasted in a fluid-bed roaster and the calcine is smelted in an electric furnace. The roaster gases are treated in an acid plant. IntroductionSmelting began at Falconbridge in 1930 with the first blast furnace treating high-grade ore containing 2-3% nickel. In 1933, the Falconbridge concentrator was built and started producing a bulk sulphide concentrate containing 4% nickel. A sinter plant was built to agglomerate and partially roast this concentrate. The sinter was smelted in blast furnaces along with high. grade magnetic ore. Matte from the furnaces was treated in Pierce-Smith converters to produce shipping matte which was refined at the company's plant in Norway."

Jan 1, 1980

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By L. E. Fischer

The background for the 630-million-dollar-plus iron ore project at Kudremukh is outlined. The system and plants for mining, crushing, concentrating, transporting via a slurry pipeline, filtering and shiploading 7.5 million metric tons of iron ore per year are fully described. The mode of operation and the problems encountered in such a transfer of North American technology to developing countries are analyzed. Difficulties encountered during construction are discussed and the progress milestones made over a two-year period are enumerated.

Jan 1, 1979

By R. D. Brown

The first step in achieving a rationalization of Canada's crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By Marcelle A. Hauseux

"The Turgeon Lake granite lies 5 miles north of Baie Johan Beetz, Quebec, at the eastern margin of the Grenville Province. The rocks are classed as granites, granulites, quartzites, biotite schists and gneisses, and amphibolites. The granite's uraniferous character is manifested by phosphuranylite, uraninite, and metamict .zircons associated with magnetite. Field anomalies occur in irregular pods, conformable with the tectonic foliation, in bands roughly paralleling sedimentary bedding. Associated features diagnostic of uraniferous granite are smoky quartz, brick-red feldspar, magnetite and a coarse to pegmatitic grain size. The granite is chemically and physically heterogeneous. Metasediment-granite contacts are diffuse or sharp, and usually conformable to bedding. The regional foliations within all rock types are coherent, and sedimentary structures are often preserved within both metasediments and granite. Autometasomatism probably was a strong granitization agent.A uranium reconcentration into fold-axial zones from original sediments which have been highly granitized during at least two phases of folding is suggested from the available data."

Jan 1, 1977

By John J. Laffin

"Nova Scotia Department of Mines and Energy Throughout the history of Nova Scotia, trends in the production and use of its coal resources have resulted in major impacts on the economy and society of the province. Current trends in coal demand locally, nationally and internationally are having and will have an increasing positive effect on Nova Scotia over the next twenty years-in terms of energy supply, job creation and general economic development. Coal for electrical generation is an immediate and key objective of Nova Scotia's energy plan; and, in the long term, coal-derived fuels will meet the province's needs for transportation fuels. Demand for metallurgical coal is also expected to increase, especially if the merchant coke plant currently under investigation becomes a reality.Meeting these coal supply and utilization objectives in the face of increasing environmental, social and economic constraints poses a tremendous technical challenge. Work has begun on projects to expand coal production capacity and to adapt new technologies for coal preparation and utilization to the specific needs of Nova Scotia; much more work will be required in the coming decade in order to succesfully tap this resource.IntroductionThe energy problem facing Atlantic Canada has a few unique features not found in the rest of the country. Canada, as a whole, has access to a diverse mix of energy resources, including crude oil, natural gas, coal, hydro and uranium, with the result that crude oil supplies only about 40 per cent of Canada's primary demand. In contrast, foreign crude oil dominates Atlantic Canada's energy mix, supplying over 70 per cent of the primary energy demand.This results in important differences in various sectors. Nationally, about 5 per cent of the electricity is generated from oil whereas last year in Nova Scotia approximately 40 per cent of the electricity generated was from imported oil. Residential, commercial and industrial space heating, and industrial process heating in Atlantic Canada was almost 100 percent dependent on foreign oil. This is in sharp contrast to the situation in central and western Canada, which have access to secure domestic natural gas, oil and hydro electricity."

Jan 1, 1982

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954

By Dave Ecobichon, Éric Côté, Simon Nickson, Michel Leclerc

The feasibility assessment of a mineral deposit requires the construction of a geo mechanical model of rock mass properties, for the purpose of preliminary mine design. The Noranda Technology Centre has been involved in the development of geomechanical models for several mineral deposits at the feasibility stage. Each model is constructed through intact rock testing, geotechnical core logging, geotechnical mapping and rock mass classification. Rock mechanics principles are used to develop conceptual stope designs and propose possible mining sequences. This methodology is applicable to both new mining projects and to the development of new areas within anoperating mine. This paper explains how the geomechanical model is developed and reviews its application to several case studies.

Jan 1, 1996

By G. J. Biefer

"Fatigue and corrosion fatigue measurements were carried out on five commercially available metals -four steels and an aluminum alloy -which are used as structural materials in mine shaft conveyances. In the corrosion fatigue measurements, drain waters collected in the shafts of three different Canadian mines were used as corrodents. The mine waters had been selected on the basis of their relatively large differences in acidity and/ or composition.It was found that the corrosion fatigue strengths of the four steels were similar, despite their differences in tensile properties, and that the type of water used in the tests had little effect on the results. Mild steel showed the highest and most consistent values of the damage ratio (ratio between the corrosion fatigue and the plain fatigue strengths at 107 cycles). The corrosion fatigue behaviour of the aluminum alloy (ASTM Type 6061-T6) was found to differ markedly in the three mine waters. A high damage ratio (i.e., superior performance) was shown in a mine water in which the corrosion attack was uniform; much lower damage ratios were shown in waters which produced localized corrosion attack. Corrosion rates were too low to be deter-mined conveniently by conventional weight-loss methods, but calculations from polarization curves provided a rapid demonstration that corrosion rates were distinctly lower in the mine water which produced high damage ratios."

Jan 1, 1967

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By Edward R. Rose

This paper summarizes and emphasizes the potential importance of Canadian rare-earth occurrences, and recommends that efforts to locate and evaluate rare-earth deposits should be increased. Increasing world markets, depending on intensive applied research into the numerous unique and remarkable chemical and physical properties of the rare-earth elements (REE), are developing; their properties and uses are becoming better known; methods of separation are much improved. The REE group comprises a Cerium (Light) subgroup of 7 metals and an Yttrium (Heavy) subgroup of 9 metals. REE are trace elements in many rocks and minerals, and major constituents of more than 50 rare-earth minerals, many of which are difficult to detect and identify. They occur preferentially in acidic and alkaline igneous and metamorphic rocks, including carbonatites, as well as in placer deposits, certain uranium deposits, phosphate rocks and others. The main ores now are bastnaesite (in Precambrian carbonatite), monazite and xenotime (in Recent beach sands) as well as uraninite and brannerite (in Huronian quartz-pebble conglomerate) and loperite (perovskite) and apatite (in alkaline complexes). World resources are summarized. Twenty mines in 1973 produced an estimated world total of about 31,000 tons of contained rare-earth oxides (REO), 19,341 tons of which came from one mine at Mountain Pass, California. A selected fifteen, of 315 or more Canadian occurrences, are briefly described and compared, and their relative merits indicated. Their abundance and variety suggest the possibility of finding high-grade deposits in many geological terranes in Canada.

Jan 1, 1979