Search Documents

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By J. Buckle

"Recognition of the diamond potential of the Wawa subprovince was initially determined from regional data using a kimberlite model. The world’s largest stable Precambrian craton, the Superior Province, is considered to be favourable for the emplacement of diamondiferous kimberlite. The Wawa area is located near the intersection of intra-craton structures visible in the regional magnetic data.The Enigma project is located north of the town of Wawa in northern Ontario. From field evidence and background research, it became obvious that in the Wawa area there were at least two potentially diamond-hosting events, Archean lamprophyric volcaniclastics and Proterozoic kimberlites. The host lamprophyric rock does not contain the classical KIM signatures. However, to complicate the Enigma, stream sediment samples within 200 m of the diamond-bearing lamprophyre produced a typical suite of kimberlite indicator minerals.The micro- and macro-diamond content of the Wawa lamprophyric volcaniclastic rocks is typically 0.2 ct/t to 1 ct/t, although it can be higher locally. The economic diamond potential of these Archean dykes, sills and irregular lamprophyre bodies is still under-explored (Kaminsky, 2002, unpubl.). Oasis Diamond Exploration is currently exploring the area using geophysical, geochemical, and geological data."

Jan 1, 2002

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

By J. C. Allan

THE purpose of this paper is to outline the pogress made in the development o the gravity separation method o ore dressing known as Sink-and-Float, which, in the opinion of the writers, has now reached a stage justifying the claim that this new method marks a highly important advance in the technique . The essential feature of the newest development of this process is the extremely accurate separation achieved. This is responsible for higher extraction in the sink-and-float unit on coarse sizes and, in consequence, for substantially higher overall recoveries. Whilst this is the most remarkable feature of the new process, it has further important contributions to make to ore dressing under the following heads: (1) The introduction of the sink-and-float separator as a buffer helps to iron-out irregularities in the mill feed. By supplying a concentrate of constant grade to the flotation section, the process also indirectly improves overall recovery. (2) The addition of a sink-and-float unit to an existing mill results in substantial increase in capacity at low per ton capital cost. (3) Where the plant can be installed underground for the pre-treatment of low-grade ores, there is a saving in hoisting costs, and excellent 'fill' is provided near the point of use. ( 4) Low-grade mixed oxide-sulphide copper ores may be pre-concentrated, thereby producing a flotation feed sufficiently rich to render the oxide residue from such flotation economic for subsequent treatment by leaching or other methods. (5) Application of the process eliminates hard gangue constituents which cause high grinding costs, or gangue constituents which adversely affect flotation. The plant is compact and easily controlled. No highly skilled operators or expensive reagents are required, and the labour and power per ton are low. The separator is extremely flexible, working equally efficiently on any throughput up to its maximum capacity.

Jan 1, 1940

By Roger V. Pierce

IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centred upon haulage, hoisting equipment, mill flow-sheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain orebodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered orebodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an orebody and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials o mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining.

Jan 1, 1943

By A. E. Cameron

The curve of coal production in Nova Scotia over the past forty years shows a definite maximum reached in 1913. Continued production to this maximum will require a greater tonnage per man-day, and this means there cannot be any increase in total man power used in the operations. There are still large reserves of coal but much of it will require washing or beneficiating to make a usable product. By-product recovery based on the present product ion is relatively satisfactory. Further development of secondary industries requires adequate markets for the bulk materials produced by the processing. It also requires access to other raw materials as well as markets for the principal product of the operations. Scientific investigation and research are needed to prove the quantity and value of lower grade or poorer quality coals, and methods for their recovery and utilization. Economics of further processing of present and future production must be investigated beforehand, if a successful development is to be assured. Such development cannot be expected largely to replace present markets. Production of coal for genera l use must continue to form the major function of the coal industry of the Province. Costs per ton must decrease, or subsidies or other assistance must increase, if the industry is to survive. Costs of investigation and research and costs of capital outlay for further development muse be met.

Jan 1, 1944

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Abstract-Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock /over­ burden interface; 2.glacial erosion and dispersal of a recognizable signature of mineralization into the glacialsediments; 3, preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites); 4. correct identification of specific till units and associated ice movement history; 5. collection of adequately large and representative samples; 6. appropriate sample preparation and processing; 7, appropriate geochemical analyses; and 8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited controlover till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 ?m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By H. C. Wade

"Description and UseDischarge liners or pulp lifters as they are sometimes called are a trough type liner used at the discharge end of the mill where ground ore passes to the trunnion.There are basically two methods of discharging pulp. The First and most common is the overflow method. Here ground ore travels from the feed to the discharge end where it exits through the discharge trunnion in an overflowing manner, hence the name ""overflow"". (See Figure I) The second method of discharging pulp is the grate method. With this method you block-off the trunnion and hold the ore inside the mill for a longer period of time. This allows only the desired size of ore out of the mill. Ore passes through the grate liners, into the Vibrathane Discharge liner, and finally down to the trunnion. Greater control of the ore size results wit1 this method as compared to the overflow method and it also eliminates reclassifying and regrinding. (See Figure 2)Types in UsePresently the majority of discharge liners in use today are rubber. (Metal insert and rubber covered) In some extremely course applications steel and nihard are used."

Jan 1, 1980

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Erwin L. Zodrow

"IntroductionThrough an extensive coal sampling project in the Sydney coalfield of Nova Scotia during 1981 - 1984 involving a majority of the mineable coals (Zodrow, 1985, Fig. 1), a sizeable inventory on trace, minor and major metals was established. In this paper, results of studying the inventory are summarized, concentrating mainly on the relationship that exists between metal variations and thickness of coal channel samples (i.e. trends) and on explaining the trends in geochemical and sedimentological terms. As an over-all conclusion the Everglades peat of Florida is proposed as a modern-day analogue to Upper Carboniferous peat swamp development that took place in the Sydney Basin.Data InventoryFor this study 17 channel samples were cut , 8 cm to 14 cm channel width and 8 cm to 10 cm depth, from 10 successive coals which in stratigraphically descending order are as follows: Point Aconi (3), overrider Lloyd Cove (2), Lloyd Cove (2), Stubbart (2), Harbour (4), Backpit (I), Phalen (,I), Shoemaker (1) and McAulay (I), where bracketed values signify the number of channel samples cut from a seam (Zodrow, 1985, Fig. I). Each channel sample was subdivided by 15 em incremental length yielding a total sample size of 137 for analysis. By appropriate modern techniques these samples were analyzed to determine concentration levels for 32 chemical elements and ash content, the average results of which are presented in Table 1.Tests were also made for Pd, Pt, Ga, Nb, Cd, Cs, Sm and W but their concentration levels in many instances hovered on the lower detection limits that were used and on this accounts are excluded from discussion. Ashing, when necessary for the determination of concentration levels, was done for 12 hours at a temperature not exceeding 450°C. Concentration levels for the elements are reported in reference to whole-coal or whole-coal equivalents and discussed on this basis. In the course of the analyses, lower detection limits received careful attention."

Jan 1, 1986

By D. C. Kaliampakos, A. G. Benardos

The existence of quarries near or even within the boundaries of urban centres is the cause of many environmental problems, despite their significant contribution to the cities’ development. Hence, the question arises as to how quarrying activities can be compromised within the spirit of sustainable development in big cities. In the case of Athens, two dominant, though opposite opinions have been formed. The first argues that all quarries must be forced to suspend their activities as soon as possible; the second presses for the continuation of quarrying. Consequently, the question is transposed on the dilemma between improved environmental conditions and economic development. This paper demonstrates that if a complete redesign is employed to specific, nonvisible quarrying sites, the continuation of quarrying activities is acceptable. It is a good compromise between the economical demand and environmental protection.

Jan 1, 2000

By C. Ketata, M. C. Rockwell

During the operation of a mineral processing plant, the unit processes are investigated by analyzing the data extracted by means of stream sampling. The data structure is identical to the time series form. Data analysis is a crucial step in understanding the plant performance. To control the plant performance efficiently, it is very important to avoid sampling errors, which is impossible. However, it is possible to minimize these errors. The factors influencing these errors are divided into two categories: material properties illustrating its heterogeneity, and sampler features. The purpose of this paper is to study the influence of the material composition variation on sampling errors, and to compare our evaluation method with that of Gy. Note that the stream mass flowrate is assumed to be constant during the sampling process.

Jan 1, 2001

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By J. W. Sanger

The establishment of a central steam-heating system in Winnipeg and its inauguration in October, 1924, has attracted a considerable amount of attention. Not only does it excite the curiosity of the engineer, but it has stirred financial and civic bodies throughout Canada to such a degree that there is now a much keener general interest in this particular type of public utility than has been shown heretofore. This does not mean that we may expect a mushroom growth of central-heating systems in all our larger Canadian cities in the near future, but it does mean that the pioneer work which Winnipeg is now doing will undoubtedly be used to guide others in their judgment as to the feasibility of similar projects elsewhere. The success of the municipal hydro-electric system in Winnipeg, and the low rates for electricity resulting therefrom, was without a doubt the most important factor influencing the citizens of Winnipeg to venture into this new field. The events which led up to the central steam-heating proposal in Winnipeg are interesting.

Jan 1, 1926